Material Safety Data Sheet; Hazardous Ingredients; Reactivity Data; Fire And Explosion Hazard Data - Oki OKIPAGE8z Limited Warranty

Material Safety Data Sheet

OKIPAGE 8z Toner (Type 6) 52111701
MSDS #58331801
For more information, contact Oki Data at:
2000 Bishops Gate Boulevard
Mount Laurel, NJ 08054-4620
Emergency Information:
call 1-800-OKI-DATA (1-800-654-3282); US & Canada Only
Emergency First Aid Procedures
Emergency Procedure
Toner Dilute by giving two glasses of water and
swallowed induce vomiting by administering
(ingested) Syrup of Ipecac (follow manufacturer's
instructions). Seek medical attention.
NEVER give anything by mouth or attempt
to induce vomiting in a person who is
unconscious.
Toner inhaled. Remove person to fresh air. Seek medical
attention.
Toner gets Flush eyes with large quantities of cool
in the eyes water for 15 minutes, keeping the
eyelids open with fingers. Seek medical
attention.
Note Small amounts of toner on skin or clothing can easily be
removed with soap and cold water. Hot water makes
toner harder to remove.

Hazardous Ingredients

Styrene-Butyl Acrylate Copolymer (91% by weight)
CAS# 25767-47-9
OSHA TWA 15 mg/m 3 for total dust
ACGIH TLV 10 mg/m 3 for total dust
Carbon Black (5-7% by weight)
CAS# 1333-86-4
3
OSHA TWA 3.5 mg/m
3
ACGIH TLV 3.5 mg/m
Polypropylene (less than 3% by weight)
CAS# 9003-07-0
OSHA TWA 15 mg/m 3 for total dust
ACGIH TLV 10 mg/m 3 for total dust
Amorphous Fumed Silica (less than 1% by weight)
CAS# 67762-90-7
3
OSHA PEL 15.0 mg/m for total dust
3
ACGIH TLV 10.0 mg/m for total dust
Note This product is not regulated under Section 313 of
SARA, Title III.
Physical Data
Melting Point: 110°C (230°F)
Boiling Point: Not applicable
2
MSDS (continued)
Vapor Pressure: Not applicable
Vapor Density (Air=1): Not applicable
Evaporation Rate (Butyl Acetate=1): Not applicable
Specific Gravity (H O=1): 1.15
2
Solubility in water: Negligible
Appearance and odor: Black granules, no odor

Fire and Explosion Hazard Data

Flash Point (Method Used): Not applicable
Flammable Limits
Lower Explosive Limit: Not applicable
Upper Explosive Limit: Not applicable
Extinguishing Media: Water, CO
Special Fire Fighting Procedures: Do not use methods that
may create a dust cloud, such as high pressure water and/or
steam
Unusual Fire and Explosion Hazards:
– Organic components decompose at 200-455°C (392-
851°F).
– Material may explosively combust when finely
suspended in air.
– Thermal decomposition of organic components may
result in release of oxides of carbon and nitrogen.
Health Hazards Data
Routes of Entry: Inhalation, Ingestion, Eyes, Skin.
1. Styrene-Butyl Acrylate Copolymer
Subcutaneous implantation of polymeric styrene powder in
rats has induced tumors at the site of implantation.
2. Carbon black
(Group 2B "Possible Carcinogen"; IARC)
Overexposure to carbon black is associated with causing
irritation, conjunctivitis, and corneal hypoplasia of the
eyes; minor irritation and eczema of the skin; and irritation
and bronchitis. Long-term inhalation exposure may be
associated with causing lung cancer.
3. Polypropylene
(Group 3 "Not Classifiable"; IARC)
Subcutaneous implantation of polypropylene powder in
rats has induced tumors at the site of implantation.
4. Amorphous Fumed Silica
(Group 3 "Not Classifiable"; IARC)
Overexposure to amorphous silica has been associated
with causing irritation of the lungs and pneumoconiosis.
Long-term inhalation exposure may be associated with
producing tumors in laboratory animals.

Reactivity Data

Stability: Stable
Polymerization: Will not occur.
Hazardous Decomposition Products: Thermal decomposition
may result in release of oxides of carbon and nitrogen.
Temperature: Do not expose to temperatures above 200°C
(392°F).
Incompatibility: Avoid exposure to strong oxidizers.
, Dry Chemical, or Foam
2