Advanced; Hdd Manage - Q-See QC804 User Manual

Manual Add
If you have changed the default settings of any remote device which you wish to use with
your NVR, you will need to use the Manual Add button at the bottom of the window to
add this device to the list of connected devices. This applies to cameras and DVRs which
were previously connected but later removed from the list of connected items. Items being
accessed from outside your local network will also need to be added using this button.
Within the Manual Add window, some information may already be displayed but it may not be
correct for the device you are intending to connect.
Channel - Select an available channel to
which you want to assign this device.
Manufacturer - You can leave this
unchanged.
IP Address - If this device is connected to
the same network as the NVR, the IP address
will appear in upper portion of the Remote
Device window along with the device name.
If this device is located outside of your local
network, you will need to determine the
IP address locally to the device (see the
Remote Monitoring Guide).
TCP Port - The default is 3777. Devices
being accessed over the Internet may
be using a different port. You will have
determined this during setup.
User/Password - Enter the user name and password you set for the device. The default user
name and password for QC-Series IP cameras are admin and admin. For other brands,
please consult your product manual.
Remote Channel - Leave this unchanged.
Decoder Buffer - Ranges from 80 to 480, but it is better to leave it at the default value of 280.
58
REMOTE DEVICE
4 IP Address Port Device ID Manufacturer Type
1 10.1.1.65 Port 1 YZC2OC061966 Private IPC
Manual Add
2 10.1.1.67 Port 2 YZCAU192012 Private IPC
3 Channel 10.1.1.68 Port 4 TC2FW25600095 Private IPC
1
4 196.219.8.50 4000 Private
Manufacturer Private
IP Search IP Address Add None
IPC.myq-see.com Filter
TCP Port 37777
Device Added
User admin
channel Edit Delete Status IP Address Port Device ID
Password
1 196.610.6.46 37777
Remote Channel 1
2 10.1.1.67 Port 2 YZCAU192012
280
Decoder Buffer
3 10.1.1.68 Port 4 TC2FW25600095
4 Save 10.1.1.65 Cancel Port 1 YZC2OC061966
Delete Manual Add
OK Cancel
PICTURE 4-31

4.6 ADVANCED

The settings in this menu cover user accounts, hard disk management, video display, and
system maintenance.

HDD MANAGE

This displays some of the same information found in the HDD Info window in the Info menu
(see Section 4.2) but this window allows you to make additional settings.
The drive name and status is displayed.
The status indicators are:
O Drive is operating normally.
X Indicates an error
- Hard drive not installed
? Hard drive is damaged
Clicking on Alarm Set opens the Abnormality window which is covered immediately
following this section.
Alarm Release – this turns off any disk alarm that may be occurring.
You can set the hard drive to four states:
Normal operation. The device records (writes) files to disk and plays (reads)
Read/Write
them.
Read Only No more files can be recorded onto the drive, but existing files can be viewed.
Format Reformats the hard drive.
If you are having problems with the hard drive, including corrupted files,
Recover
selecting Recover causes the drive to re-set, but does not erase its contents.
CAUTION! Reformatting the hard drive will erase all recorded events.
No changes will take place unless the Execute button is pressed once you've made your
selection. The drive's status will be displayed next to the Type heading below the pull-downs.
If you make changes and press Execute, the NVR will restart once you press OK to exit. You
cannot right-click out of the menu.
PICTURE 4-32
PICTURE 4-33
59