• To reduce the risk of fire, electrical shock, or motor damage, do not 10 • Troubleshooting ....17 use a solid-state speed control with this fan. Use only Hunter speed controls.
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician. 42891-01 • 11/19/10 • Hunter Fan Company...
Page 5
Understanding Mounting and Installer’ s Choice® Support Brace Hunter’s patented mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard, or Angle mounting.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Do not over tighten. Flat Washer 3” Wood Screw For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing toward the ceiling peak. 42891-01 • 11/19/10 • Hunter Fan Company...
3 • Assembling Pipe / Ball Assembly 3 • Assembling Pipe / Ball Assembly As discussed in " Step1 - Getting Ready", your Hunter fan can be Figure 3a installed in either the standard or angled mounting positions. 2 1/2” Pipe / Ball Assembly Included with the fan are two pipes: one 4 1/2"...
Once assembled, do not remove the downrod. 4-4. Raise the fan and place the hook on the ceiling plate through the hole in the rim. 42891-01 • 11/19/10 • Hunter Fan Company...
5-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 42891-01 • 11/19/10 • Hunter Fan Company...
6-5. Install the third canopy screw into the canopy. Once all three screws are in, tighten them. Note: If the tabs are already engaged, do not rotate. Step 6-3 Step 6-4 Ceiling Plate Canopy Canopy Hanger Screw Screw Ball 42891-01 • 11/19/10 • Hunter Fan Company...
7 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 7-1. Install the grommets into the blades by hand. Step 7-1 (Detail) 7-2. Place each blade between a blade iron and medallion. Install three blade screws to attach the medallion to the blade iron.
Page 13
8 • Completing Your Installation With a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. The switch housing assembly is made up of three sections: the switch housing gasket, the upper switch housing, and the lower switch housing/light assembly.
Page 14
NOTE: Both plug connectors are polarized and will only fit together one way. Make sure that both connectors are properly aligned before connecting them together. Incorrect connection could cause improper operation and damage to the product. Steps 8-9 - 8-11 42891-01 • 11/19/10 • Hunter Fan Company...
Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket(s) may result in fire hazard or improper operation. Steps 8-16 - 8-17 42891-01 • 11/19/10 • Hunter Fan Company...
9-5. The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust and dirt. Use a dry or slightly damp lint free cloth to clean the blades.
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 866-268-1936) or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Parkway #400 Memphis, Tennessee 38016 42891-01 • 11/19/10 • Hunter Fan Company...