Table of Contents
Advertisement
3 .
3 .
3 .
3 . 3 .
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 configuration with the Intel
through the onboard Intel
These connectors are set to S t a n d a r d I D E
S S S S S t a n d a r d I D E
t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk
t a n d a r d I D E
t a n d a r d I D E
t a n d a r d I D E
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the S A T A
See page 4-27 and 4-28 for details.
NCCH-DR SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
•
•
•
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
S A T A 1
S A T A 1
S A T A 1
S A T A 1
S A T A 1
S A T A 2
S A T A 2
S A T A 2
S A T A 2
S A T A 2
2 - 2 8
2 - 2 8
2 - 2 8
2 - 2 8
2 - 2 8
®
6300ESB integrated RAID controller.
NCCH-DR
You must install Windows
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1) is available only if you are using
Windows
®
2000/XP.
Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
When using the connectors in I D E
hard disk drive to the SATA1 or SATA2 connector. Refer to the table
below for the recommended SATA hard disk drive connections.
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
M a s t e r
M a s t e r
M a s t e r
M a s t e r
M a s t e r
S l a v e
S l a v e
S l a v e
S l a v e
S l a v e
®
Matrix Storage Technology
S t a n d a r d I D E
S t a n d a r d I D E
S t a n d a r d I D E mode by default. In
S t a n d a r d I D E
S A T A
S A T A
S A T A
S A T A M o d e
M o d e
M o d e
M o d e
M o d e item in the BIOS to [RAID].
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXN2
RSATA_RXP2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXN1
RSATA_RXP1
GND
®
2000 Service Pack 4 or the Windows
I D E
I D E
I D E
I D E mode, connect the primary (boot)
U s e
U s e
U s e
U s e
U s e
B o o t d i s k
B o o t d i s k
B o o t d i s k
B o o t d i s k
B o o t d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
®
XP
Advertisement
Table of Contents
