Names of the parts Wash selector Wash timer Outer cover of the spin tub Water-filling entrance Inner cover of the spin tub Control panel Spin timer Overflow filter Major frame Water level adjusting lever Spin tub Lint filter (installed by user) Valve cover Pulsator Wash tub...
Safety precautions Please insert the power cord into When the machine is normally special receptacle with rated vol- using, please put the power plug tage. Be sure to use single-phase at the location easily to be insert- three pins receptacle. The earthing ed and extracted by hand.
Safety precautions Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the machine by yourself. rotation is slow. Take special care of the children. Do not put any hot or heavy items Do not wash laundries with volatile ( such as the kettle with hot water ) materials (such as thinner, petrol etc.).
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package, please take out the lint filter from the document bag, install it to the overflow filter of the wash tub.
How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Back Soft item Extend the drain hose from the side of spin tub Front Put soft items on the ground. Lean the machine down gently with the front surface facing the Figure 1 ground.
Preparation before washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put down the drain hose .
The musts in washing The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.
Washing sequence Wash timer Wash selector Spin timer Water inlet (To set to below 2 minute, (standard current, (to set to below 1 minute, first set to 6 minute then strong current) first set to 2 minute then turn it back. it can increase turn it back.
Rinsing Rinse with water-filling 1.Put the laundries into the wash tub. Select suitable current according to the laundries. 2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing.
Spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin: (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Push Proper Proper The laundries No gland are slanting (2) Close the inner and outer cover of the spin tub.
Disposal after washing After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing.
Cleaning the overflow filter 2. Take off the corrugation pipe. Water level Dismantle the upper part of the adjusting lever corrugation pipe inside Corrugation overflow filter ( as indicated in Pipe Figure 1). 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water.
Trouble-shooting Answer to question If the laundries fall to the outer side of the spin tub contact If the laundries fall to the outer side of the spin tub,please the after-sales service department. When the remained water is frozen Prevent the freezing (be sure to discharge the water completely after using) After complete draining, set the "WASH SELECTOR"...
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.