Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eiki LC-XT1
Summary of Contents for Eiki LC-XT1
- Page 1 MULTIMEDIA PROJECTOR LC-XT1 MODEL OWNER’S INSTRUCTION MANUAL...
-
Page 2: To The Owner
Eye damage may result. • If the projector is not to be used for an extended time, unplug the projector from the power outlet. READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE. TO THE OWNER LC-XT1 purchased the projector or the... -
Page 3: Safety Precautions
Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition. projector exhibits distinct change LC-XT1... -
Page 4: Federal Communication Commission Notice
Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician. THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE COMPLIANCES LC-XT1... - Page 5 SELECTING COLOR SYSTEM PICTURE IMAGE ADJUSTMENT NORMAL FUNCTION PICTURE SCREEN ADJUSTMENT SETTING SETTING MENU SETTING LANGUAGE APPENDIX OPERATING WIRELESS MOUSE MAINTENANCE TEMPERATURE WARNING INDICATOR AIR FILTER CARE AND CLEANING LAMP MANAGEMENT LAMP REPLACEMENT CLEANING THE PROJECTION LENS TROUBLESHOOTING TECHNICAL SPECIFICATIONS LC-XT1...
-
Page 6: Features And Design
• Wireless Mouse The Remote Control Unit supplied with this projector has Wireless Mouse function for the connected computer. This function enables you to operate both projector and computer with this Remote Control Unit only. LC-XT1 function minutes. DVI terminal for... - Page 7 LC-XT1...
- Page 8 LC-XT1 This projector uses nominal input voltages of 100-120 V or 200-240 V AC. The projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.
- Page 9 LC-XT1 Before setting up the projector, install the Projection Lens on the Projector. 1.Before installation, check where the projector is used and prepare suitable lens. For specifications of the Projection Lens, refer to the manual separately attached or contact the sales dealer where you purchased the projector.
- Page 10 LC-XT1...
- Page 11 Pull out the terminal by holding the handle. Replace the terminal. Insert the terminal along Guide to fit Plug into Socket. Tighten the screws to secure the terminal. 4 terminal slots for expansion to tune to diversity of signals from computers and LC-XT1...
- Page 12 LC-XT1...
- Page 13 LC-XT1...
- Page 14 LC-XT1...
- Page 15 LC-XT1...
- Page 16 LC-XT1...
- Page 17 LC-XT1...
- Page 18 LC-XT1...
- Page 19 LC-XT1...
- Page 20 LC-XT1...
- Page 21 LC-XT1...
- Page 22 LC-XT1...
-
Page 23: Turning On The Projector
If the TEMPERATURE WARNING indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center. NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling Fan is working, TEMPERATURE WARNING INDICATOR flashes red. LC-XT1... - Page 24 LC-XT1...
- Page 25 LC-XT1...
- Page 26 LC-XT1...
- Page 27 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to “RGB”, and then press the SELECT button. When connect the computer output Type (Red, Green, Blue, Horiz. Sync and Vert. Sync.)] from the computer to the A/Pr, G/Y, B/Pb, H/HV and V jacks. LC-XT1...
- Page 28 LC-XT1...
- Page 29 LC-XT1...
- Page 30 Move the arrow to “Stored” and press the SELECT button. parameter is memorized in the selected Mode. To activate the Mode manually adjusted in this PC ADJUSTMENT Menu, select the Mode at the SYSTEM SELECT Menu. (Refer to page 28.) RIGHT/LEFT button LC-XT1...
- Page 31 Adjustment of the horizontal height or vertical width of the image. NOTE: The Display area, the Horiz. scale and the Vert. scale cannot be adjusted when “480p”, “S7Sp”, “HDTV72Op”, “HDTV1O35i” or “HDTV1O8Oi” is selected on the SYSTEM MENU (P28 and 29). LC-XT1...
- Page 32 LC-XT1 NOTE: The Fine sync and the Total dots cannot be operated when the input signal is digital from DVI terminal or “RGB” is selected on the SYSTEM MENU (P28 and 29). The Progressive cannot be selected when the input signal is digital from DVI terminal or “...
- Page 33 Total dots and Screen position for most computers. It will take about 10 seconds. NOTE: Some computers may not be fully adjusted with the “Auto Image Function”. In that case, use the “Picture Image” and/or “Picture Position” adjustments (P32, 33) to make fine-adjust then after the “Auto Image Function” is executed. ‘-‘C’’ LC-XT1...
- Page 34 The image data in other than XGA (1024 X 768) is modified to fit the screen size in the initial mode. The normal “Panning Operation” may not function properly if the computer system prepared with the “PC Adjust” is used. LC-XT1...
- Page 35 When connect the separate Y/C video output from the video equipment to the VIDEO/Y and C jacks, select “Y/C” in VIDEO SOURCE Menu. S-Video When connect the S-Video output from the video equipment to the S-Video jack, select “S-Video” in VIDEO SOURCE Menu. LC-XT1...
- Page 36 LC-XT1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Another dialog box VIDEO SYSTEM Menu will appear. Press the POINT DOWN button and a red-arrow icon will...
- Page 37 LC-XT1...
- Page 38 LC-XT1...
- Page 39 (Power Management mode). In this Power Management mode, the Projection Lamp is automatically turned on when the input signal connected or the projector is operated with any button on the Side Control or the Remote Control. (For example “On” or “Off”). LC-XT1...
- Page 40 To return to the normal code (Mode 1), operate both projector and Remote Control in the ways above again. NOTE: When the ALL-OFF switch on the Remote Control Unit is turned to “ALL-OFF” the remote transmit code automatically returns to the normal code (Mode 1). LC-XT1...
- Page 41 SELECT button. Another dialog box LANGUAGE Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the language that you want to set, and then press the SELECT button. LC-XT1...
- Page 42 Turn the projector on first, and then turn on your computer. When the NOTE: When the computer has no mouse port, connect the Serial Port of the computer to Control Port of the projector with the Control Cable for Serial Port LC-XT1...
- Page 43 When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel, lens, or optical elements inside it. This condition may degrade the quality of the projected image. When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning. LC-XT1...
-
Page 44: Lamp Status Display
When any of 4 lamps becomes out, the Lamp Mode is changed over from 4 lamps to 2 lamps. And when any of 2 lamps are out, the projector operates with 1 lamp. Lamp Mode can be switched to 4 lamps or 2 lamps manually. Refer to SETTING section on page 39, 40. LC-XT1... - Page 45 “Lamp Replacement Monitor Timer” on page 41.) NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER when the lamp is not replaced. CAUTION : Do not operate the projector while any of lamps is removed. It may result in malfunctions, fire hazard, or other accidents. LC-XT1...
- Page 46 (When you reconnect the projector, remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in order of: Projector and computer) 6. If the problem still exists, check the following chart. LC-XT1...
- Page 47 LC-XT1...
- Page 48 LC-XT1...
- Page 49 LC-XT1 HDB 15-PIN TERMINAL (ANALOG) Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied). • When connecting the Macintosh computer, use MAC/VGA Adapter (supplied). • When connecting the Analog signal from DVI terminal of the computer to this terminal, use DVI/VGA Adapter (supplied).
- Page 50 LC-XT1...
- Page 51 LC-XT1...