Audio Dubbing A Pre-Recorded Cassette (Sv-667I Only) - Samsung SV-667I Instruction Manual

Audio Dubbing a Pre-recorded Cassette (SV-667I Only)

GB
EJECT STANDBY/ON
VIDEO L AUDIO R
PROG
LINE IN 2
3
3
4
REC MENU
OK
SPEED DUB TV/VCR TIMER
5
A.DUB
-0:05:23
38
With the Audio Dubbing function, you erase the previously
recorded sound and replace it with a new soundtrack from:
A CD player
A microphone connected to a sound system
A cassette player
Restriction:
Audio dubbing is applicable only to the longitudinal audio track
(normal audio).
1 Connect an RCA audio cable to the appropriate output on your
sound system (CD/cassette player for example).
2 Connect the other end of the RCA audio cable to the audio input
connectors (L, R) on the front of your VCR.
3
Insert the pre-recorded cassette on which the audio track is to be
❿ II
replaced, and press the to start playback.
4
Find the scene that you want to over-dub and press
remote control.
5
Press DUB.
Result: Your VCR is now in the Audio dubbing Pause mode.
6 On the sound system, locate the point on the CD or cassette at
which you wish to start playback.
Example: The track that you wish to record on the cassette.
7
When you are ready:
Start playback on the sound system
Press REC on the remote control.
Result: The soundtrack is replaced on the pre-recorded cassette.
The new sound will be recorded on the normal sound
track of the tape, and the original sound will remain on
the Hi-Fi sound track.
To hear the new sound and original sound mixed
together, press the Audio button on the remote control
until the MIX option is displayed (see page 31).
Using the TV Buttons on the Remote Control
(SV-667I/SV-466I Only)
Your VCR remote control will work with Samsung televisions and
compatible brands.
To determine whether your television is compatible, follow the instructions
below.
1
Switch your television on.
2
Point the remote control towards the television.
3
Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
appropriate numeric buttons.
Brand Codes
SAMSUNG 01 to 06
AKAI 09, 23
GRUNDIG 09, 17, 21
LOEWE 02
PANASONIC 08, 23 to 27
❿ II Result: If your television is compatible with the remote control, it
on the
will switch off. It is now programmed to operate with the
remote control.
If several codes are indicated for your television brand, try
each one in turn until you find one that works.
When you change the batteries in the remote control, you
must reprogramme the code, following the same procedure.
You can then control the television using the following buttons.
Button Function
TV STANDBY/ON Used to switch the television on and off.
TV or VCR Used to switch between the TV and VCR modes.
Only the VOL (
buttons are operational in VCR mode.
-/-- Used to enter a two-figure programme number.
Example: For programme 12, press -/-- followed
INPUT Used to select an external source.
+ –
VOL or Used to adjust the volume of the television.
PROG/TRK Used to select the required programme.
or ❷)
(
DISP./ Used to switch between an external source and
the television tuner.
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
2
Brand Codes
PHILIPS 02, 20, 22
3
SABA 13, 14, 22 to 24
SONY 15, 16
AUDIO
THOMSON 13, 14, 24
TOSHIBA 07, 16 to 19, 21
AUDIO
TV
AUDIO
+ –
or ) and TV STANDBY/ON
by numeric buttons 1 and 2.
GB
VCR STANDBY/ON TV STANDBY/ON
SLOW
1
SHUTTLE
V-LOCK
2
CLR/RST F.ADV INDEX
-/--
SELECT
TV VCR INPUT
REPEAT
CLR/RST F.ADV INDEX
-/--
SELECT
TV VCR INPUT
5
REPEAT
4
DISP./
VOL PROG/TRK
5
TV VCR INPUT
REPEAT
6
DISP./
VOL PROG/TRK
6
VCR INPUT
REPEAT
DISP./
VOL PROG/TRK
7
39