IMPORTANT NOTE Warning The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Exterior interference such as lightning and static Precaution electricity can affect normal operation of this recorder. If this occurs, turn the recorder off and on again with the STANDBY/ON button, or disconnect and then reconnect the AC power cord to the AC power outlet. The recorder will operate normally.
An audio disc on which 44.1kHz PCM Audio is This unit can play back DVD-R discs recorded and recorded finalised with a Samsung DVD video recorder. It may Plays CD-DA format audio CD-R and CD-RW discs. not be able to play some DVD-R discs depending on The unit may not be able to play some CD-R or the disc and the condition of the recording.
Page 6
DVD-RW (VR mode) This DVD Recorder can - This is a format that is used for recording data on a allow you to protect the DVD-RAM or DVD-RW disc. You can repeat contents of your discs, recording, editing, deleting, partial deletion, as described below.
Step 4 : Other type of connecting the Audio Contents output cable............18 Method 1 : Connecting to your TV ........18 Method 2 : Connecting to a stereo amplifier with analog output jacks ............19 Getting Star Getting Star Method 3: Connecting to an AV amplifier with a Warning................2 digital output jack ............19 Precaution ..............3...
Page 8
Recor ding Zooming-In................55 Recor ding Using PIP(Picture in Picture)...........56 Before Recording.............34 Using Last Mark ...............56 Recordable discs..............34 Using Bookmarks.............57 Recording Formats ............35 Using Markers ..............58 Recording Mode...............35 Playing an Audio CD/MP3 ........59 Unrecordable pictures............35 Playing an Audio CD (CD-DA)/MP3 .......59 About INFO.
A variety of functions with an easy-to-use user General Features interface The integrated menu system and the messaging function allow you to perform desired operations both easily and conveniently. With a DVD-RAM or DVD-RW disc, you can edit recorded images, create a playlist, and edit images in a specific sequence according to The DVD-R100E allows you to record and play high your requirements.
All rights reserved; No part or whole of this user’s noted that the data of the disc may manual may be reproduced or copied without the prior be lost when changing formats. written permission of Samsung Electronics Co. English -...
Page 11
Step 3 Step 6 Recording Finalising & Playing on other DVD components There are two different recording methods, Direct To play your DVD on other DVD components, finalising Recording and Timer Recording. Timer recording is may be necessary. First, finish all editing and recording classified as recording type : Once, Daily or Weekly or operations, then finalise the disc.
Description Front Panel 1. STANDBY/ON 11. REC Turns the recorder on and off. Starts recording. 2. DV-IN 12. PR ( Connects external digital equipment with a DV jack. Select TV preset channels. Same as PROG buttons in remote control. 3. AV4 IN Connects external equipment.
Rear Panel The fan always revolves when the power is on. Ensure a minimum of 10cm clear space on all sides of the fan when installing the product. 1. DIGITAL AUDIO OUT 4. AV1(TV) OUTPUT SCART Connects to an amplifier having a digital input jack. 5.
Tour of the Remote Control 10. MENU Button Brings up the DVD Recorder’s setup menu. 11. OK/DIRECTION Buttons (UP/DOWN or LEFT/RIGHT Buttons) This button functions as a toggle switch. 12. RETURN Button Returns to a previous menu. 13. REPEAT Button Allows you to repeat a title, chapter, track or disc.
Quick Overview Connecting A Quick Overview presented in this guide will give you enough imformation to start using the recorder. & Setting Up Step 1 : Unpacking This section involves various methods of connecting the DVD player to other external †...
Step 1: Unpacking Step 2: Connecting SCART Cable Accessory There are several ways to connect your DVD Recorder using scart cables. Check for the supplied accessories below. Select one of the following connections that best suits you. Method 1 : Antenna + DVD Recorder + TV Method 2 : Antenna + VCR/satellite receiver/cable box + DVD Recorder + TV Method 3 : Antenna + DVD Recorder + external...
Method 1 : Antenna + DVD Method 2 : Antenna + Recorder + TV VCR/satellite receiver/cable box + DVD Recorder + TV You can connect your DVD Recorder to the television using the SCART cable if the appropriate input is available on the television.
Method 3 : Antenna + DVD Step3 : Other type of Recorder + external decoder connecting the Video box + TV output cable If you connect external decoder box to DVD recorder, you can record scrambled channels received through the built-in TV tuner in DVD Recorder. There are several ways to output video signal not using scart cables.
Method 2 : Connecting to an Step 4 : Other type of S-video output jack connecting the Audio Connect an S-video cable(not supplied) between the S-VIDEO OUT jack on DVD Recorder and S-VIDEO IN output cable jack on the TV (or AV amplifier). You will enjoy high quality images.
Method 2 : Connecting to a Method 3: Connecting to an AV stereo amplifier with analog amplifier with a digital output jacks output jack If your stereo amplifier only has audio input jacks If your AV amplifier only has a Dolby Digital, MPEG-2 or (L and R), use the analog audio out jacks.
Method 2 : Connecting a Step 5 : Connecting to Camcorder to the AV 4 Input AV3, AV4, DV input jack jacks You can also use the AV 4 IN jacks on the front panel of the DVD Recorder. You can record from connected equipment.
Setting the Remote Control Step 6 : Preparing the Your DVD Recorder remote control will work with Samsung televisions and compatible brands. Remote Control Install Batteries in the Remote Control Open the battery cover on the back of the remote.
Page 23
PIONEER TV STANDBY/ON +58,+59,+73,+74 RADIOLA TV STANDBY/ON +06,+56 RADIOMARELLI TV STANDBY/ON +57 TV STANDBY/ON +45,+46 TV STANDBY/ON +74 SABA TV STANDBY/ON +57,+72,+73,+74,+75 SALORA TV STANDBY/ON +74 SAMSUNG TV STANDBY/ON +01,+02,+03,+04,+05,+06,+07,+08,+09 SANYO TV STANDBY/ON +41,+42,+43,+44,+48 SCHNEIDER TV STANDBY/ON +6 - English...
On-Screen Menu Navigation System Setup The on-screen menus allow you to enable or disable various functions on your DVD Recorder. Use the following buttons to open and navigate through the on-screen menus. No Disc Setup System √ √ Language √ √ Audio √...
Auto Channel scan will be started. Plug & Auto Set up Channel scan Now, Scanning. Your DVD Recorder will automatically set itself up when it is plugged in for the first time. TV stations and clock will be stored in memory. The process takes a few minutes.
Set Auto clock tap “On” or “Off” using Clock Set the …† buttons. DVD-RAM(VR) Clock Set Time Date Year 2004 This menu is used to set the current time. Auto Clock : You need to set the time to use timer recording. MOVE RETURN EXIT...
Press OK button to continue. Auto Setup If you want to exit, press MENU button. DVD-RAM(VR) Install Auto Setup √ √ Manual Setup √ √ Your data will be lost. Press [OK] to continue, [MENU] to exit. This feature allows you to manually set the DVD Recorder tuner band to Antenna or Cable, whichever you connected to the Antenna In jack during initial setup.
Press the †… buttons to select a PR Manual Setup (program) you wish to edit, delete, or swap. And then press OK button. Select Edit, Delete, or Swap. You can add preset channel that Auto Channel Search DVD-RAM(VR) Manual Setup missed.
Select the desired time using the …† CM Skip Time Setting buttons, then press the √ or OK button. DVD-RAM(VR) System Clock Set √ √ Install √ √ CM Skip Time : 15 Sec 15 Sec √ √ When a program recorded on a DVD-RAM, a DVD-RW, 30 Sec AV1 Output : Video...
Setting Up NICAM Options Setting Up Scart Jack Options NICAM programmes are divided into 3 types. NICAM If you connect external device (VCR/satellite receiver/ Stereo, NICAM Mono and Bilingual (transmission in cable box) or TV to DVD Recoder with Scart another language).
Use the …† buttons to select the Setting Up the Language desired sub menu and press the OK or √ button. Features Audio Language: For the speaker sound. Subtitle Language: For the disc subtitles. Disc Menu Language: For the disc menu If you set the player menu, disc menu, audio and contained on the disc subtitle language in advance, they will come up...
Audio Options Setting Up the Audio Options Digital Output 1. PCM : Select this when you have no equipment that can decode Dolby Digital (or MPEG-2) Allow you to setup the Audio device and sound status signal. When you play Dolby Digital (or depending on the audio system in use.
Display(Video) Options Setting Up the This function depends on disc type. It may not work for Display(Video) Options some disc types. TV Aspect This function allows you to setup the TV screen Depending on the type of television you have, you may settings.
Select “Rating Level” you want using Setting Up the Parental †… buttons, then press the √ or OK button. Control • For example, if you select up to Level 6, discs that contain Level 7, 8 will not play. Larger number indicates the program is more intended to adult use only.
This section shows various DVD recording This recorder can record on the following discs. methods. DVD-RAM DVD-RW DVD-R DVD-RWs and DVD-RAMs are rewritable. DVD-Rs are non-rewritable Compatibility between Samsung Recorder and Other Company’s Recorder Disc Types Recording Recording Finalising Additional Recording in format Device...
Recording Formats Recording Mode When you insert an unused disc, the following message Select one of four recording modes by pressing the appears; Since available functions differ depending on REC MODE button repeatedly while the unit is in Stop the disc type, select a disc that best fits your prefer- mode for the desired recording time and picture quality.
About INFO. Key Recording the current TV program you are watching Before you start The INFO function allows you to view the current status and progress of playback and recording. Check that the disc has enough available space for the Depending on the kind of disc and status, the displayed recording.
Page 38
To pause recording Press the PROG ( / ) or number ~ ) buttons to select the current Press the REC PAUSE button to pause a recording in program you want to record. progress. Press the REC PAUSE button again to resume recording.
Press the REC button. Recording from external equipment you are watching To pause recording Press the REC PAUSE button to pause a recording in progress. Press the REC PAUSE button again to resume recording. PROG You can switch channels by pressing the Before you start ( / ) buttons while recording pauses.
When the INFO. button is pressed again: Reviewing Images Being Information about playback will appear. Recorded (Time Slip) DVD-RAM(VR) Playing Info Name 04/APR/2004 12:00 Title 15/15 Created Time 04/APR/2004 12:00 Length - --:--:-- - Playing Time 00:02:05 Title Protection Not Protected 24 APR 2004 SAT 12:00 This function lets you watch recently recorded...
To view the current status of the disc and progress Making a One Touch of recording : Press the INFO. button, and the information about the disc will appear. Recording (OTR) DVD-RAM(VR) Disc Info Disc Name Total Title Total Playlist Recordable Time 03:00 SP Protection...
Set timer recording option. Making a Standard Timer • The Timer Recording screen is displayed. Fill the input items using the arrow buttons and number buttons. œ √ : Moves to the previous/next item, …† : Sets a value. • Source : The video input source (AV1, AV2, AV3 AV4 or DV), or the broadcasting Before you start channel you want to make a timer...
Press the OK button. Editing a Standard Timer will appear on the front panel. It means that a timer recording is registered. If you make a mistake Press the œ √ button to select the item you want to change. If the timer settings overlap The programs are recorded in order of priority.
Press the †… buttons to select “Edit”, Deleting a Standard Timer and then press the OK button. The Timer Recording screen is displayed. Edit the items you want to modify. See the “Making a Standard Timer” section for more information on Timer Recording Input items. DVD-RAM(VR) Scheduled Record List Remaining Recording Time 02:12 SP...
Press the OK button. Using the ShowView The information concerning the programme is displayed. Feature When using the ShowView function for the first time with stored stations, the programme number flashes. This one time, you must enter the PR number manually by pressing the †…...
Press the OK or √ button to set the ShowView Extended “ShowView Extended” time by increments of 10 minutes. DVD-RAM(VR) Programme ShowView Record √ √ Standard Timer √ √ To prevent delays or overruns, DVD Recorder has a ShowView Extended : Off √...
Recording the Standard Timer List When the start time in the Scheduled record list reaches while the set is in power off, the set will be powered on and start the recording automatically. When the scheduled recording is operating, the programme being recorded will not display on TV.
Before Playing Playback Read the following information before playing a disc. Region code (DVD-Video only) Both the DVD recorder and the discs are coded by region. These regional codes must This section introduces basic functions of playback match in order for the disc to play. If the codes do not match, the disc will not play.
Place a disc gently into the tray with the This DVD recorder can only operate with disc’s label facing up. discs that are compatible with DVD-RAM NOTE For DVD-RAM discs, insert the printed side facing up. Standard Version 2.0. Playback and/or recording may not work for some types of discs, or when specific Press the OPEN/CLOSE button to close operations, such as aspect ratio...
Using the Search Functions Using the Disc & Title Menu Some type of discs contain a dedicated menu system that allows you to select special functions for the title, such as chapters, audio tracks, subtitles, film previews, information on characters, etc. For DVD-VIDEO discs Press the DISC MENU button to enter the disc menu of the disc.
About ANYKEY Skipping Chapters or Tracks During play, you can search quickly through a chapter or track. During play, press the SKIP ( button on the remote control. If you press the œœ button, The ANYKEY function allows you to easily search for a it moves to the beginning of the chapter or track or desired scene by accessing title, chapter, track, and marker(DVD-RAM, DVD-RW(VR mode)).
If you want to move to a desired time to Using the Repeat Function help you find a scene. Press the ANYKEY button during playback. DVD-VIDEO 1/10 1/40 00:01:45 D 5.1CH Playing Repeatedly(Repeat Playback) MOVE CHANGE Using the REPEA utton Using the REPEA utton Press the …†...
Page 53
Press the REPEAT button repeatedly to select the “Track or Disc” you want to Using the ANYKEY b utton Using the ANYKEY b utton play repeatedly. Press the ANYKEY button. Music Repeat : Track Play Option : Normal 01. TRACK 1 00 : 52 01.
Page 54
- To return to normal playback - - To return to normal playback - Press the REPEAT button repeatedly to Press the REPEAT(A-B) button select “Off’. repeatedly to select “Off”. Press the CANCEL button to return to normal playback. Using the ANYKEY b Using the ANYKEY b utton utton...
Selecting the Subtitle Selecting the Audio language Subtitle languages may not work depending on the disc Audio languages may not work depending on the disc type. This is only available during playback. type. This is only available during playback. Using the SUBTITLE b utton Using the A UDIO b...
Changing the Camera Angle Zooming-In When a DVD-VIDEO contains multiple angles of a particular scene, you can select the Angle function. This is only available during playback. Press the ANYKEY button during playback or pause. DVD-VIDEO 1/10 Press the ANYKEY button during play- 1/40 back.
Using PIP(Picture in Picture) To view the current status and progress of playback : Press the INFO. button. The PIP function allows you to view a sub screen together with the main screen. DVD-VIDEO Info Title 1/10 You can view TV while playing a DVD disc. Chapter 1/40 Playing Time...
Using Bookmarks Playing Back a Bookmark Press the MARKER button. (V mode) Press the MARKER button during playback. Press the œ √ buttons to select a bookmarked scene. Bookmark Bookmark MOVE RETURN MOVE PLAY CANCEL RETURN Press the OK button when the desired Press the OK or button to start scene appears.
Using Markers Playing Back a Marker (VR mode) Press the MARKER button. Press the MARKER button. Press the œ √ buttons to select a bookmarked scene. Marker Marker RETURN MOVE PLAY CANCEL RETURN Press the OK or button to start Press the OK button when the desired playing from the selected scene.
The Buttons on the Remote Control Playing an Audio CD/MP3 Playing an Audio CD (CD-DA)/MP3 Each disc has a variety of menu functions available. Playing an Audio CD(CD-DA) Insert an audio CD (CD-DA) into the disc tray. The audio CD menu appears and the tracks (songs) are played automatically.
Page 61
Playing a MP3 Disc The Buttons on the Remote Control Insert a MP3 Disc into the disc tray. The MP3 menu appears and the tracks(songs) are played automatically. Music Repeat : Off Play Option : Normal Straight from the heart 00 :22 ROOT Bryan Adams...
Page 62
Play Option Mode To Program Tracks You can register a maximum 30 tracks in the playlist. The Play Option can be used with an audio CD or MP3 in the Play or Stop mode. Press the ANYKEY button. Repeat Mode will be highlighted. Press the ANYKEY button.
Press the …† œ √ buttons to select a Playing a Picture CD picture. JPEG Photo Index 6 / Slide Show ROOT / DSC01189 Page 2 / MOVE RETURN There are two types of Picture CD. One is a CD with only JPEG files.
Press the …† buttons to select Playing the Title List “Title List”, and then press the OK or √ button twice. The Title List screen is displayed. DVD-RAM(VR) Title List No. Title Length Edit 01 19/APR/2004 1 00:00:21 √ √ 02 19/APR/2004 1 00:00:03 √...
Page 65
Press the INFO. button once again. Then you can Title List Screen Elements check the information about the title under playback. DVD-RAM(VR) Playing Info Name 21/APR/2004 11:50 PR11 Title 1/16 Created Time 21/APR/2004 12:00 DVD-RAM(VR) DVD-RAM(VR) Title List Title List Length 00:07:43 LP Playing Time...
Editing This section introduces basic functions of DVD editing and explains both edit functions for the recording on a disc and edit functions for the entire disc. Title List Title refers to a recorded video and audio stream. Title List shows a list to help you select a title. Since the title list consists of the information on stream that is actually recorded, if one title is deleted, that title cannot be played again.
Locking(Protecting) a Title Press the œ √ buttons to select “On”, and then press the OK button. Follow these instructions to lock an entry to protect it The key icon on the information window from accidental deletion. for the selected entry changes to the locked status.
Deleting a Section of a Title Press the …† buttons to select “Delete”, and then press the OK button. Follow these instructions to delete a section of a Title List entry. DVD-RAM(VR) Title List (VR mode) No. Title Length Edit 01 Drama 00:00:21 √...
Page 70
Press the OK button at the starting Press the …† buttons to select “Delete”, point. and then press the OK button. The image and starting point time are displayed in the The selected section has been deleted. section deletion starting point window. DVD-RAM(VR) Edit Title List DVD-RAM(VR)
Press the OK button at the end point. Advanced Editing (Play List) DVD-RAM(VR) Make Scene Scene No. 001 Start Start 00:00:10 Creating a Playlist 00:10:00 Make New Playlist Return 19/APR/04 12:00 Follow these instructions to create a new playlist entry 00:10:00 from a recorded title.
Playing Entries in the Playlist Press the …† buttons to select “Play”, and then select the OK button. Follow these instructions to play the playlist entries. The playlist entries will be played. DVD-RAM(VR) Edit Playlist (VR mode) No. Title Length Edit 01 23/APR/2004/0 00:00:21 √...
Renaming a Playlist Entry Enter the desired characters using the …† œ √ buttons. Follow these instructions to rename a playlist entry, i.e. to edit the title of a playlist entry. DVD-RAM(VR) Rename Dolphin (VR mode) A B C D E a b c d e f g h i F G H I J...
Editing a Scene for the Playlist Playing a Selected Scene Follow these instructions to edit scenes for a playlist. Press the arrow buttons to select the scene you want to play, and then press (VR mode) the OK button. The playlist entry to be played is selected. Press the PLAY LIST button.
Page 75
Press the OK button at the end point of Modifying a Scene (Replacing a Scene) the scene. DVD-RAM(VR) Modify Scene Scene No. 001 Press the arrow buttons to select the Start scene you want to modify, and then press the OK button. Start 00:00:00 00:00:25...
Page 76
Moving a Scene (Changing the Position of a Scene) You cannot move the selected scene to the position of the next scene, because the NOTE selected scene should be inserted before that position, which requires no action. Press the …† œ √ buttons to select the Depending on the kind of disc, the displayed scene you want to move (change the screen may have a slight difference.
Press the OK button at the end point of Copying a Playlist Entry to the the scene. Playlist DVD-RAM(VR) Add Scene Scene No. 004 Using the PLA Y LIST b utton Start Using the PLA Y LIST b utton Start 00:00:15 00:00:15 Sclence...
Press the MENU button after the Press the …† buttons to select “Delete”, operation has finished. and then press the OK button. The menu screen will disappear. DVD-RAM(VR) Edit Playlist No. Title Length Edit 01 Science 00:00:17 √ √ 02 Sky 00:00:06 You can create up to 999 scenes on one √...
Enter the desired characters using the Disc Manager arrow buttons. DVD-RAM(VR) Rename Disc A B C D E a b c d e f g h i F G H I J Editing the Disc Name k l m n o K L M N O p q r s t P Q R S T...
Disc Protection Formatting a Disc Disc Protect allows you to protect your discs from being Use these instructions to format a disc. The cartridge formatted or deleted due to unintended operations. write protect tab should be set to the unprotect position. The disc protect should also be cleared.
Press the …† buttons to select “Disc DVD-RW Manager”, and then press the OK or √ You will be prompted with the confirmation message ‘Choose the recording format for button. DVD- RW.’ DVD-RAM(VR) Disc Manager Disc Name √ √ DVD-RW(VR) Disc Manager Disc Protection : Not protected...
Cartridge Protection Info Finalising a disc Disc Protect allows you to protect discs from disc After you record titles onto a DVD-RW/DVD-R disc with formatting and program deletion due to unintended your DVD recorder, it needs to be finalised before it can operations.
You will be prompted with the message 'Do you want Unfinalising a disc (V/VR mode) to finalise disc?'. If you select Yes, you will be prompted again with the message 'Disc will be finalised. Do you want to continue?' DVD-RW(VR) Disc Manager Disc Name √...
Page 84
Press the œ √ buttons to select “Yes”, and then press the OK button. The disc is unfinalised. A DVD-RW can be finalised or unfinalised in Video mode. NOTE Finalise Unfinalise Mark DVD-Video(RW) DVD-RW(V) Additional recording, protection Operation Same as DVD-Video and deletion are possible.
Troubleshooting Additional If your product malfunctions, go through the checkpoints below before contacting a Samsung authorized service Information center. Power The input is displayed for a while when the power is turned on. The DVD recorder requires some time Checkpoint 1 to initialize and the input will be displayed for approx.
Page 86
Differences between Using REC PAUSE Button and Play mode settings are different from the settings Using Stop Button during Recording configured in the Settings menu. The disc does not support all selected Each press of the Stop button during Checkpoint 1 Checkpoint 1 functions.
Video Timer Recording The disc revolves, but no image or bad quality Timer lamp flickers. images are displayed. Check there is enough space in the Checkpoint 1 Check whether there is damage to or Checkpoint 1 disc for recording. any foreign material on your disc. Check whether the current disc is Checkpoint 2 Some low quality discs may not play...
Page 88
Allow for proper distance. Remove obstacles between your DVD recorder If the problem still persists, contact a Checkpoint 3 and the remote control. nearby Samsung service center. Check whether the batteries are empty. Checkpoint 2 Check for the TV/DVD selection button. Checkpoint 3 Other I forget my password for parental supervision.
Specifications Power requirements 230V AC, 50Hz Power consumption 35 Watts Weight 3.75Kg General Dimensions 430mm(W) x 280mm(D) x 68.5mm(H) Operating temp. 5°C to +35°C Other conditions Keep level when operating. Less than 75% operating humidity Composite Video : 1.0 V p-p at 75 load, sync negative Video (AV3, AV4) S-Video input (Y: 1.0Vp-p, C: 0.286Vp-p at 75 load) Audio(AV3, AV4)
Sthn perivptwsh pou qa creiasteiv e p i s k e u h v , t o p r o i o v n a u t o v t h ı SAMSUNG qa prevpei na staleiv hv na metaferqeiv sto exousiodothmevno service, m e e v x o d v a t o u a g o r a s t h v .