Table of Contents
Advertisement
VCR
Recording a Programme with Automatic Stop
GB
This function enables you to record up to nine hours (LP) of
programmes.
Your DVD-VCR stops automatically after the requested length of
time.
1
2
3
3
4
4
4
6
5
6
5
7
LENGTH 2:30
SET LENGTH :
G
PRESS
REC
8
☛
32
Switch on the television.
To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result:
The DVD-VCR is switched on automatically.
Select:
The station to be recorded using the PROG (œ or ❷) buttons
N
or
N
The AV1, AV2 or AUX source using the INPUT button for a
satellite tuner or external video source
Result:
The channel number is displayed and the programme
can be seen on the television.
Select the recording speed by pressing the SPEED button as
many times as required (see page 30).
Hold the REC button (G) down for a while to start recording.
Result:
The record indicator appears on the television screen
and DVD-VCR display. An index is recorded on the
tape (see page 40).
Press the REC button ( G) several times to increase the
recording time in:
N
30-minute intervals up to four hours
N
1-hour intervals up to nine hours (LP)
Result:
The length is displayed on the television displays. The
selected programme is recorded for the length of time
requested. At the end of that time, the DVD-VCR stops
recording automatically.
If you wish to cancel the recording before the end, press
STANDBY/ON.
If the end of the tape is reached while recording:
N
The recording stops and power off
Using the VIDEOPLUS+ Feature
Before presetting your DVD-VCR:
N Switch on both the television and your DVD-VCR
N Check that the date and time are correct
N Insert the cassette on which the programme is to be
recorded (safety tab intact)
Up to six programmes can be preset.
1
To enter a VideoPlus, press the TIMER button.
Press the
❷¤
and ENTER buttons to select
VIDEOPLUS
Result:
A message is displayed to allow you to enter the
VIDEOPLUS+ code.
☛
If all six programmes have been set, the message
IS FULL
is displayed. Refer to page 36 if you wish to
cancel a preset recording.
2
Press the numeric buttons to enter the code opposite the
programme that you wish to record in your television magazine.
➢
If you wish to correct the VIDEOPLUS+ code that you are
entering:
N
Press the ➛ button until the digit to be corrected is
cleared
N
Enter the correct digit
3
Press the SETUP button.
Result:
The information concerning the programme is displayed.
☛
When using the VIDEOPLUS+ function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the
œ
or
❷
buttons. Refer to the following page if:
N
The programme number or times flash
N
You wish to modify the programme
4
If the programme and times are correct, press the RETURN button.
5
Press the STANDBY/ON button to activate the timer.
6
Refer to page 36 if you wish to:
N
Check that your DVD-VCR has been programmed correctly
N
Cancel a preset recording
☛
The numbers next to each TV programme listing are
VIDEOPlus+ code numbers, which allow you to
programme your videorecorder instantly with the remote
control. Tap in the VIDEOPLUS+ code for the programme
you wish to record.
™ VIDEOPLUS+ is a trademark of Gemstar Development Corporation. The VIDEOPLUS+
system is manufactured under licence from Gemstar Development Corporation.
VCR
1
.
TIMER
TIMER METHOD
STANDARD
VIDEOPLUS
RETURN
œ ❷
ENTER
VIDEOPLUS
CODE ---------
➛
CODE:0-9
CORRECT:
RETURN
ENTER
1/JAN TUE
12:09
PR DAY
START STOP V/P
-- ---- --:-- --:---- -
-- ---- --:-- --:---- -
-- ---- --:-- --:---- -
-- ---- --:-- --:---- -
-- ---- --:-- --:---- -
-- ---- --:-- --:---- -
❿
œ ❷
SET:
RETURN
DELETE:CLEAR
5
33
GB
Hide quick links:
Advertisement
Table of Contents
