Kenwood KRF-V5090D Instruction Manual page 16

Preparing for surround sound
8 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the appropriate center speaker setting.
If you have selected "LRG" as the Front speakers setting,
1 CNTR NML (normal) : An average size Center speaker is
2 CNTR LRG (large)
3 CNTR OFF
If you have selected "NML" as the Front speakers setting,
1 CNTR NML (normal) : An average size Center speaker is
2 CNTR OFF
9 Press the SETUP key again to accept the setting.
•The Surround speaker setting indication "SURR NML" appears.
0 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the appropriate Surround speaker setting.
If you have selected "LRG" as the Center speaker setting,
1 SURR NML (normal) : Average size Surround speakers are
2 SURR LRG (large)
3 SURR OFF
If you have selected other than "LRG" as the Center speaker
setting,
1 SURR NML (normal) : Average size Surround speakers are
2 SURR OFF
• When the setting "SURR OFF" is selected, the procedure skips
to step #.
! Press the SETUP key to accept the setting.
• The Surround Back speaker setting indication "BS" appears.
@ Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the appropriate Surround Back speaker setting.
If you have selected "LRG" as the Surround speaker setting,
1 BS NML : Average size Surround Back speaker is connected
to this model.
2 BS LRG
: Large Surround Back speaker is connected to this
model.
3 BS OFF
: Surround Back speaker setting mode to this model
is OFF.
If you have selected "NML" as the Surround speaker setting,
1 BS NML : Average size Surround Back speaker is connected
to this model.
2 BS OFF
: Surround Back speaker setting mode to this model
is OFF.
(KRF-V6090D only)
If you have selected "NML" or "LRG" as the Surround Back
speaker setting,
1 SPEAKER : Surround Back signal will be output from
SURROUND BACK speaker terminal and SURR
BACK L/SURR BACK PRE OUT terminal as
monaural.
2 PRE OUT : Surround Back signals will be out put from SURR
BACK L/SURR BACK and SURR BACK R PRE OUT
terminals as stereo.
16
EN
connected to this model.
: A large Center speaker is connected to
this model.
: Center speaker setting mode to this
model is OFF.
connected to this model.
: Center speaker setting mode to this
model is OFF.
connected to this model.
: Large Surround speakers are connected
to this model.
: Surround speaker setting mode to this
model is OFF.
connected to this model.
: Surround speaker setting mode to this
model is OFF.
# Press the SETUP key again to accept the setting.
• The Subwoofer re-mix setting indication "SW RE-MIX" scrolls
across the display.
• If Subwoofer is turned OFF, Subwoofer re-mix setting is not
visible.
$ Use the MULTI CONTROL knob or MULTI CONTROL %/fi
keys to select the appropriate Subwoofer re-mix setting.
1 RMX ON : Subwoofer re-mix set mode to this model is ON.
2 RMX OFF : Subwoofer re-mix set mode to this model is OFF.
% Press the SETUP key to accept the setting.
4
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
• In step 4 and 5, indications appear only for the selected channels
of the speakers that require adjusting.
1 Press the SETUP key to begin TEST TONE.
• This model enters the speaker volume level adjustment mode.
The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or MULTI CONTROL %/fi keys.
1 AUTO
2 MANUAL
2 Press the SETUP key again to select either AUTO or MANUAL.
Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to adjust the volume level of the test tone output from the
speaker channel to be adjusted.
For AUTO selection, the test tone is heard from the speakers
in the following sequence for 2 seconds each:
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
• If any of the speaker is set as OFF during SP SETUP, the TEST
TONE adjustment for the speaker will be skipped.
(KRF-V6090D only)
• If you have selected "SPEAKER" as the Surround Back setting,
"RB" and "LB" are not appeared but "BS" is appeared on the
Display.
3 Press the SETUP key.
• The test tone is turned off. This model enters the mode for
inputting the distance to the speakers.
4 For MANUAL selection, press the SETUP key each time to
select the speaker channel.
ª