Advertisement

O P E R A T I N G R A N G E
This cordless telephone operates at the
maximum power allowed by the Federal
Communications Commission (FCC).
Even so, the handset and base can
communicate over only a certain distance
—which can vary with the locations of the
base and handset, the weather, and the
construction of your home or office.
If the handset is moved to a point where
the base and handset can no longer
communicate, the handset will sound two
short beeps when you make a call,
indicating that you are out of range. Move
close to the base to restore normal
operation.
2
User's Manual
for Cordless
Telephone 7220
Fold open this manual for information about this
telephone's installation and operation. Please
read Part 1— Important Product Information,
included in this package.
If you receive a call while you are out of
range, the handset might not ring — or if
it does ring, the call might not connect
when you press P. Move closer to the
base, then press P to answer the call.
If you move out of range during a phone
conversation, you will hear noise or
interference. To improve reception, move
closer to the base.
If you move out of range while on a call,
the phone will be left "off the hook." To
hang up properly, walk back into range,
periodically pressing P until the
PHONE light goes off.
Part 2
© 1998 Philips Consumer Communications L.P. All rights reserved.
Printed in Mexico. 848233698 Issue 1AT&T
Changing Channels
This cordless telephone has an advanced
AutoSelect feature that minimizes the
chance of interference.
In the unlikely event that you notice noise or
interference while using the handset:
Press C.
1
2
If the interference does not clear,
continue to press C until you find
a clear channel (your call will not be
interrupted
—OR—
Move closer to the base and press
C.
NOTE: You must be in range to change
channels.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 7220 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for AT&T 7220

  • Page 1 O P E R A T I N G R A N G E Changing Channels If you receive a call while you are out of This cordless telephone operates at the range, the handset might not ring — or if This cordless telephone has an advanced maximum power allowed by the Federal it does ring, the call might not connect...
  • Page 2: Installation

    I N S T A L L A T I O N Modular Jack Standard AC Outlet Base Antenna AC Adapter Charging/Handset in Use Light Power Cord PAGE/HANDSET LOCATOR Button Telephone Line Cord you will always need to press P base goes on to show the handset The instructions below are for both table is in the right position to charge...
  • Page 3: Operation

    O P E R A T I O N Making A Call Handset Volume Press P, and wait for the The handset volume can be set to three different levels. Each time you press V PHONE light to go on steadily. When you hear a dial tone, dial the the level changes.
  • Page 4 M E M O R Y Storing Numbers Just Dialed This cordless phone can store 10 telephone numbers that you can dial just by pressing Whenever you make a telephone call, you p and one of the number buttons. can store the number you dialed in memory. Press R instead of entering the telephone Additionally, Model 7220 offers a memory location accessed by pressing m.
  • Page 5: Charging The Handset Battery Pack

    B A T T E R I E S Replacing the Charging the Handset If it’s more convenient for you, you can Handset Battery Pack Battery Pack leave the handset in the base all the time. Remove the battery case cover on It is impossible to overcharge the batteries.
  • Page 6: In Case Of Difficulty

    I N C A S E O F D I F F I C U L T Y If you have difficulty operating this phone, phone should operate properly. If it to allow all of them to ring. Try un- try the suggestions below.

Table of Contents