Konica Minolta magicolor 8650DN Specification & Installation Manual

Konica Minolta
magicolor 8650DN
Specification & Installation Guide
magicolor 8650DN Specifications
Type Full Color Printer
Photoconductor OPC
Print System Laser electrostatic print method
Developing System Dry-type dual-component
HMT development method
Fusing System Belt Fusing System
Resolution 19,200 x 600 dpi
Paper Plain Paper: (16 lb. to 24 lb.)
Thick Paper 1 (24.25 lb. to 40 lb.)
Thick Paper 2 ( 41.75 lb. to 55.5 lb.)
Thick Paper 3 (55.75 lb. to 68 lb.)
Thick Paper 4 (68.25 lb. to 72 lb.)*
OHP Transparencies*, Postcards*,
letterhead, colored paper, envelopes*,
label sheets*, banner paper (24.25 lb. to
55.5 lb.)
Duplex: Plain Paper (17 lb. to 24 lb.);
Thick Paper 1/2/3/4 (24 lb. to 68 lb.)
*Can only be fed through the bypass tray.
Print Sizes

Bypass Tray

12" x 18" L to 5.5" x 8.5"L/P, 4" x 6" L ,
8" x 13" L *, banner paper
Tray 2
11" x 17" L to 8.5" x 11" L /P, 5.5" x 8.5" L ,
8" x 13" L *
Tray 3
12" x 18" L to 8.5" x 11" L /P, 5.5" x 8.5" L ,
8" x 13" L *
* This setting must be changed by an authorized
Konica Minolta Service Technician.
Paper Tray Capacity 1sT Tray and 2nd
Plain Paper: 500 sheets;
Thick Paper 1/2/3: 150 sheets
Bypass
Plain Paper: 150 sheets;
Thick Paper 1/2/3/4, OHP
Transparencies, postcards, label sheets:
20 sheets; Envelopes: 10; Banner Paper:
10 sheets
Print Output Tray Plain Paper: 250 sheets
Capacity Thick Paper: 10 sheets
Overhead Projection
Transparencies: 1 sheet
(Tray 1):
(Universal Tray):
(Universal Tray):
Tray:
Tray:
Warm-up Time Less than 75 seconds
(at room temperature 73.4° F)
Image Loss Width Leading edge: 0.188"
Trailing edge: 0.125"
Rear edge: 0.125"
Front edge: 0.125"
First Print Time Color: Less than 8.5 seconds
B/W: Less than 5.9 seconds
Paper Size
Print Speed (ppm)*
(Full Color/Black)
11" x 17"
8.5" x 14"
8.5" x 11" P
8.5" x 11" L
5.5" x 8.5" P
5.5" x 8.5 L
*Using 1st Tray and 8.5" x 11"
Multiple Prints 1 to 999 sheets
Power Requirements 120 V, 12 A, 60 Hz
Power Consumption 1,500 W or less
Dimensions 25.25"(W) x 27.75"(D) x 25"(H)
Space 65.75"(W) x 46"(D)
Requirements*
2
(FS-519 Finisher and SD-505 Saddle Kit installed)
67.75"(W) x 46"(D)
Memory (available 1,024 MB (60 GB HDD)
hard disk space)
Weight Approx. Approx. 174 lb.
Footnote 1 There are five Foolscap sizes: 220 x 330 mm L , 8.5" x 13" L ,
8.25 "x 13" L , 8.125" x 13.25" L and 8" x 13" L . Any one of these
sizes can be selected. For details, contact the technical representative.
Footnote 2 The indicated space requirements represent the space required
to pull away the finisher and to open the paper trays.

Duty Cycle

magicolor 8650DN: Up to 150,000. Maximum monthly
print volume supported under standard vendor
supplied service. Defines the upper end of the
expected customer volume for the device. Customers
should consider multiple machines if average monthly
volume approaches duty cycle on a continual basis.
7/2009
Speed (seconds)
17
20
35
25
35**
35
paper; **Using bypass
L
(FS-609 Finisher installed)
1