If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan . If you cannot check off every item, prepare a new fan site as described on this page .
Page 4
ANSI/NFPA 70 . If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician . 45046-01 • 01/13/11 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease . You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting . The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods .
Parts Guide . Check for any shipping damage to the motor blade irons (if applicable) in sets, or fan blades . If any parts are missing or damaged, contact your Hunter as they were shipped . dealer or call Hunter Technical Support Department at 888-830-1326 (In Canada, call 1-866-268-1936) .
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws . Do not over tighten . Flat Washer Steps 2-2 – 2-4 Ceiling Peak Ceiling Peak Large Large Opening Opening 3” Screw LEFT RIGHT Step 2-3 (Angled Ceiling Only) 45046-01 • 01/13/11 • Hunter Fan Company...
(Rotate the fan until you hear the notch pop into place . ) Steps 3-4 – 3-5 Go to 4 • Wiring the Fan . WARNING: Fan may fall if not assembled as directed in these installation instructions . 45046-01 • 01/13/11 • Hunter Fan Company...
Page 9
WARNING: Fan may fall if not assembled as directed in these installation instructions . Steps 3-8 – 3-9 Low Profile Washer Step 3-7 (Detail) Low Profile Washer Adapter Canopy Trim Ring #8-32 x 3/4” Screw Step 3-10 45046-01 • 01/13/11 • Hunter Fan Company...
. 4-7 . Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box . 45046-01 • 01/13/11 • Hunter Fan Company...
Should you need to remove the canopy trim ring, follow these steps: 1 . Twist canopy trim ring counter clockwise until it releases from canopy . Step 5-3 Step 5-4 Canopy Step 5-5 Screw 45046-01 • 01/13/11 • Hunter Fan Company...
6 • Assembling the Blades Step 6-1 (Detail) Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan) . 6-1 . Your fan may include blade grommets . If your fan has grommets, insert them by hand into the holes on the blades .
7 • Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button . This feature gives you the option of installing the fan with OR without the included light fixture .
Page 14
Detail sticker affixed to the light socket(s) may result in fire hazard or improper operation . If lights do not appear to be operating properly, see the troubleshooting section . Housing Assembly Screw 45046-01 • 01/13/11 • Hunter Fan Company...
Page 15
. (You may find the Light Bulbs breakaway connector on the (B10 Candelabra end of the extra chain . ) Base 60 Watt Maximum) Metal Rod Metal Disk Glass Bowl Cover Plate Breakaway Finial Connector 45046-01 • 01/13/11 • Hunter Fan Company...
Page 16
7-20 . Install the switch housing cap and plug button to the lower switch housing . 7-21 . Once you have uninstalled the light fixture, continue Steps 7-16 – 7-18 with step 7-6 . Male Dummy Terminal Female Dummy Terminal Plug Button Step 7-20 45046-01 • 01/13/11 • Hunter Fan Company...
. 8-6 . The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust and dirt . Use a dry or slightly damp lint free cloth to clean the blades .
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 1-866-268-1936) or visit us at our Web site at http://www . h unterfan . c om . Hunter Fan Company 7130 Goodlett Farms Pkwy #400 Memphis, Tennessee 38016 45046-01 • 01/13/11 • Hunter Fan Company...
Need help?
Do you have a question about the 21711 and is the answer not in the manual?
Questions and answers