Thank you very much for having purchased our product. Please read these instructions carefully before attempting to install, operate or service the Panasonic product. Failure to comply with instructions could result in personal injury or property damage. Please explain to users how to operate and maintain the product after installation, and this booklet should be presented to users.
GENERAL SAFETY INFORMATION WARNING: To reduce the risk of fire, electric shock or injury to persons, observe the following: 1. Use this unit only in the manner intended by the manufacturer. lf you have any questions, contact the manufacturer. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
Page 3
GENERAL SAFETY INFORMATION CONTINUED CAUTION: 1. Do not install this ventilating fan where interior room temperature may exceed 104 F (40 C). 2. Make sure that the electric service supply voltage is AC 120V, 60 Hz. 3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupation Safety and Health Act (OSHA).
SUPPLIED ACCESSORIES (4 sets) (A) For Motor/ Light Kit/ Grille Assembly of model: FV-08VSLB2, FV-10VSLB2 Appearance Appearance Quantity Quantity Part name Part name Lighting unit Grille Screw Fluorescent (ST4.2X16) lamp Machine screw Night lamp (M4X8) (B) For Housing Can of model: FV-08VSLA2 Appearance Quantity Appearance...
Page 5
INSTALLATION (JOIST MOUNTING- ) 1. Before installation, secure the fan body to adaptor by Machine screw using machine screw(M4X8). (Fig.1) (M4X8) IMPORTANT: Remove the tape from damper and adaptor Fan body before installation. As shown below: Fig. 1 Tape A=12 inches Adaptor Damper Suspension...
Page 6
INSTALLATION (JOIST MOUNTING- ) CONTINUED 3. Install the suspension bracket and the flange of fan body to joists by using long screws (ST4.2X20). Joist (If spacing A between joists is 10 1/4 12 inches, install the flange of fan body according to Fig.3-2, Fan body others according to Fig.3-1 install the product.) 4 Long screws (ST4.2X20)
Page 7
INSTALLATION (JOIST MOUNTING- ) CONTINUED 8. Finish ceiling work. Ceiling hole should be aligned with the edge of the flange. (Fig.6) 9.Follow the Fig.12-3,12-4(page 9) and the Fig.6,7 (page 8) of the original installation instruction to complete the Motor/Light Kit/Grille Assembly installation.
Page 8
INSTALLATION (JOIST MOUNTING- ) CONTINUED 5. Insert the fan body into joists. (Fig.8) Circular duct IMPORTANT: Conduit Joist Make sure that adaptor claws are properly inserted into body slots. Junction box cover 6. Secure the fan body to adaptor by using machine screw.
Page 9
INSTALLATION ( - JOIST MOUNTING ) 4 kinds of -joist hole inches (mm) mark Suspension 9/16 (14.3) bracket 11/16 (17.5) Screw 31/32 (24.6) (ST4.2X12) 1 17/32 (38.9) Fig. 10 Suspension bracket The suspension bracket can comply with different kinds of -joist. 1.
Page 10
INSTALLATION (BETWEEN JOIST MOUNTING ) CONTINUED 3. Insert the fan body between joists. Make sure the fan body is level and square Joists (perpendicular) with the joists. (Fig.13) CAUTION: Adaptor Backside of flange should mount directly to bottom of joist. Junction box Fan body Suspension bracket...
Page 11
INSTALLATION (WOODEN HEADER ) 1. Before installation, secure the fan body to adaptor by Joist using machine screw (M4X8). (Fig.1 of page 5) Header Joist Adaptor Fan body 2. Install header between joists by using nails or screws. Fig. 16 Unit: inches (mm) 3.
The unit should be serviced by qualified technicians only. Your product is designed and manufactured to ensure a minimum of maintenance. Should your unit require service or parts, call Panasonic Call Center at 1-866-292-7292 (USA) or 1-800-669-5165 (Canada). Panasonic Corporation of North America One Panasonic Way, Secaucus, New Jersey 07094 www.panasonic.com...