Playable Discs; Troubleshooting; Video And Audio; Remote Control - Dynex DX-LDVD19-10A User Manual

DX-LDVD19-10A_09-0340.book Page 25 Tuesday, April 28, 2009 4:43 PM

Troubleshooting

To change this setting you must enter your password. (The initial
password is 1234.)
When parental controls are set to OFF, all discs may be viewed.
• Password—You can change your password by entering the
old, four digit password, then entering the new, four digit
password. You must confirm the new four digit password
before the new password can be used.
..Preference Page
--(2/2)
Parental
Password Change
Default
Note: If you forget your password or the wrong password is accidentally
set, enter 1369 as the password. This will enable you to regain control.
• Default—Resets all settings (except password and parental
lock status) for this DVD player back to the manufacturers
original settings. Press ENTER to perform the reset.
3 Press SETUP repeatedly to exit the setup menus.

Playable discs

Discs Label
DVD Video
Audio CD
JPEG
Kodak CD
CD-R
CD-RW
CD+G
MPEG4
Support discs include: DVD, VCD, CD-R, CD-RW, HDCD, JPEG, CD+G,
MPEG-4, Kodak CD, and WMA.
You cannot play discs other than those listed above.
You cannot play non-standardized discs, even if they may be labelled as
above.
The performance of CD-R or CD-RW disc depends on the way the disc
was burned. In a few cases, their performance may not be consistent or
they may not even play.
This DVD Player is designed and manufactured according to the Region
Management Information that is recorded on a DVD disc. If the Region
number described on the DVD disc does not correspond to the Region
number of this DVD Player, this DVD player will not play that disc.
This Region number of this DVD Player is
Troubleshooting

Video and audio

Old Password
New Password
Confirm Pwd
Contents Size
Audio+Video 12 cm
(moving picture)
Audio 12 cm
Video (picture) 12 cm
Video (picture) 12 cm
Audio or Video 12 cm
(moving picture)
Audio or Video 12 cm
(moving picture)
Audio (picture) 12 cm
Audio+Video 12 cm
(moving picture)

Remote control

1
Warning: Do not try to repair your TV yourself. Contact authorized service
personnel.
Problem Solution
No picture or sound • Make sure that the power cord is plugged
(the screen is not lit) into a power outlet.
• Press POWER
control.
• Try another channel. The problem could be
with the TV station.
Dark, poor, or no • Select the correct picture mode. For more
picture (the screen is information, see "Adjusting the picture" on
lit), but sound is page 13.
good • Adjust the brightness. For more
information, see "Adjusting the picture" on
page 13.
• Make sure that the antenna or cable TV is
connected correctly. For more information,
see "Connecting an antenna or cable TV" on
page 8.
No color, picture is • Adjust the color saturation. For more
dark, or color is not information, see "Adjusting the picture" on
correct page 13.
Only noise (snow) • Make sure that the antenna or cable TV is
appears on the connected correctly. For more information,
screen see "Connecting an antenna or cable TV" on
page 8.
• Try another channel. The problem could be
with the TV station.
Picture has dotted • Adjust the antenna.
lines or stripes • Move your TV away from noise sources,
such as cars, neon signs, or hair dryers.
Picture has double • Use a highly directional outdoor antenna or
images change to cable or satellite TV.
Picture has a few • A few bright or dark dots on an LCD screen
bright or dark dots is normal. It does not affect the operation of
this TV.
Good picture, no • Increase the volume.
sound • Press MUTE to make sure that the sound is
not muted.
• Make sure that the audio mode is set to
STEREO or MONO. For more information,
see "Adjusting the sound" on page 14.
Audio noise or static • Move radio frequency communication
equipment, such as a cordless phone, away
from your TV.
Problem Solution
Remote control • Replace the batteries. For more
does not work information, see "Installing remote control
batteries" on page 6.
• Make sure that the batteries are inserted
correctly. For more information, see
"Installing remote control batteries" on
page 6.
• Make sure that the power cord is plugged
into an AC power outlet.
25
DX-LDVD19-10A
on your TV or the remote