Setting The Alarm Sound - Philips HF3485 User Manual

EnglisH
12
Note: If you do not press any button within 30 seconds, the appliance exits the menu and the display
shows the clock time again.
2 Press the menu - or + button to select a function (Fig. 9).
3 Press the SELECT button to enter this function (Fig. 10).
4 Press the menu - or + button to change a setting (Fig. 9).
5 Press the SELECT button to confirm (Fig. 10).
setting the alarm
setting the alarm time
When you set the alarm, you set an alarm time and light intensity and you choose the type of sound
you want to wake up to. The alarm is set when the alarm symbol is visible on the display. The light
intensity slowly increases to the selected level before the set alarm time. At the set alarm time, the
alarm sound slowly increases in 90 seconds to the selected level.
Note: You can set two different alarm times, for example if you want to wake up at a different time on
the weekend than on weekdays.
Note: The volume you set for the alarm is also used as the volume for the radio and music on your USB
stick. To set the alarm volume, press the volume increase or decrease button. If you do not want to
wake up to the lamp or to a sound, select a light intensity or volume level of 0. See sections 'Using the
appliance as a bedside lamp' and 'Setting the volume' in this chapter.
1 Push the control lever to the middle position if you want to set alarm 1. Push the control
lever to the top position if you want to set alarm 2 (Fig. 11).
The hour indication of the alarm time starts flashing (Fig. 12).
,
To adjust the time, follow steps 2 to 5.
,
2 Press the menu - or + buttons to set the hour (Fig. 9).
Note: You can only do this when the hour indication flashes. If this is not the case, push the control lever
down and up again to enter the alarm time function. You can also set the alarm time in the menu (see
section 'Menu functions' in this chapter).
3 Press the SELECT button to confirm (Fig. 10).
The minute indication of the alarm time starts flashing (Fig. 13).
,
4 Press the menu - or + buttons to set the minutes (Fig. 9).
5 Press the SELECT button to confirm or wait for a few seconds (Fig. 10).
The appliance leaves the menu and the display shows the clock time.
,
The alarm time is now set.
setting the light intensity
You can set the light intensity you prefer that takes place before the alarm goes off, .
Note: The light intensity you set is used for the alarm function as well as for the lamp function (see
section 'Using the appliance as a bedside lamp' below).
1 Press the lamp on/off button (Fig. 14).
Note: It takes approx. 1 second for the lamp to go on. This is normal, the lamp needs to heat up.
Note: You can also set the light intensity when the lamp is out, but switching on the lamp makes it easier
to determine the preferred light intensity.
2 Press the light intensity increase and decrease buttons to select a light intensity (Fig. 15).
You can choose a light intensity between 1 and 20.
If you do not want the lamp to go on gradually before the alarm goes off, set the light intensity to 0.
Tip: When you use the appliance for the first time, set the light intensity to 20. The moment you wake up,
check which light intensity level the appliance has reached by briefly pressing the light intensity increase
or decrease button. When you do this, the current alarm light intensity level appears on the display. Set
the alarm light intensity to this level for the next day.
3 To switch off the lamp, press the lamp on/off button again.

setting the alarm sound

Note: You can adjust the volume level of the alarm sound to your preference (see section 'Setting the
volume' in this chapter). If you do not want to wake up to an alarm sound, set the volume level to 0.
1 Follow the instructions in section 'Menu functions' and select the alarm sound function.
2 Press the SELECT button to confirm.
3 Press the menu - or + buttons to select the desired alarm sound.
The display shows the symbol of the selected alarm sound.
,
4 Press the SELECT button to confirm.
You can choose one of the following sounds:
- Radio (see also section 'Using the radio as alarm sound' below') (Fig. 16)
- 'Bird' sound (Fig. 17)
- 'Yoga' sound (Fig. 18)
- 'Cowbell' sound (Fig. 19)
- 'Forest' sound (Fig. 20)
- Downloaded wake-up sounds or your own music from a USB stick (see also section 'Using
music on a USB stick as alarm sound' below) (Fig. 21).
Tip: You can download more wake-up sounds at www.philips.com.
Using the radio as alarm sound
1 Follow instructions 1-4 in section 'Setting the alarm sound' to select the radio as alarm
sound.
The display shows P1, which is preset radio station 1 (Fig. 22).
,
If you want to select another preset radio station, press the menu - or + button (see section 'Using
the radio/playing music from a USB stick'). If you want to change the frequency of the preset radio
stations, see section 'Using the radio/playing music from a USB stick' in this chapter)
2 Press the SELECT button to confirm.
The selected preset radio station is now set as the alarm sound.
,
Using music on a UsB stick as alarm sound
Note: You can only use music on a USB stick if it is in MP3 or WMA format. You can check this on your
computer. The extension of the files should be .mp3 or .wma.
Refer to chapter 'USB specifications' for more USB information.
1 Insert the USB stick in the USB socket of the appliance.
2 Follow instructions 1-4 in section 'Menu functions' above to select music from a USB stick as
alarm sound.
The display shows 0001 to indicate the first song on the USB stick (Fig. 23).
,
To select another song, press the menu - and + buttons.
3 Press the SELECT button to confirm.
The selected song is now set as the alarm sound.
,
EnglisH
13