Pioneer BDP-53FD Operating Instructions Manual page 59

Problem
• No sound is output.
• Sound is not output
properly.
Multi-channel sound is not
output.
Noise can be heard when
outputting DTS Digital Audio
signals from the DIGITAL
OUT terminal.
192 kHz or 96 kHz digital
audio signals cannot be
output from the DIGITAL
OUT terminal.
Secondary audio or
interactive audio is not
output.
Sound is fast or slow.
After a disc is inserted,
Loading stays displayed and
playback does not start.
 is displayed in file names,
etc.
A message indicating low
memory appears while
playing a BD-ROM disc.
Check
Is the disc played back in
slow motion?
Is the disc played back in fast
forward or fast reverse?
Are the audio cables properly
connected?
Is the audio cable damaged? If the cable is damaged, replace it with a new one.
Is Audio Output properly
set?
Are the connected
components (AV receiver or
amplifier, etc.) properly set?
Are you trying to listen to the
sound of the HDMI OUT
terminal while watching the
picture from the VIDEO
output terminals?
Is HDMI Audio Out properly
set?
Is a DVI device connected?
For the BDP-53FD:
Is the HDMI Mode set
appropriately?
Is the audio output of the
connected AV receiver or
amplifier, etc., properly set?
Is multi-channel sound
selected?
Is the connected AV receiver
or amplifier compatible with
DTS Digital Surround?
Is HDMI Audio Out properly
set?
Are Digital Output properly
set?
When an HDMI cable is
connected, are audio signals
being output from devices
connected with cables other
than HDMI cables?
Are there too many files
recorded on the disc?
Remedy
No sound is output during slow motion play and forward and reverse
scanning.
• Connect the cable properly according to the connected devices
(page 16).
• Insert the cable firmly and all the way in.
Set Audio Output properly, according to the connected device
(page 42).
Read the operating instructions for the connected components and
check the volume, input, speaker settings, etc.
Audio signals are not output from the HDMI OUT terminal when video
signals are being output from the VIDEO output terminals. When
watching the picture of the VIDEO output terminals, connect an optical
digital audio cable or regular audio cables to listen to the sound
(page 21). Once connections are completed, use Setup Navigator to
make the player's settings (page 24).
Set HDMI Audio Out to Re-encode or PCM. (page 43).
The sound will not be output from the HDMI OUT terminal if a DVI
device is connected. Connect the device to a DIGITAL OUT terminal or
the AUDIO OUT terminals (page 21).
For some BDs, audio signals are only output from DIGITAL OUT
terminal or the HDMI OUT terminal.
Set the HDMI Mode properly, according to the connected device
(page 43).
Read the operating instructions for the connected AV receiver or
amplifier and check the audio output settings of the AV receiver or
amplifier.
Use the menu screen or AUDIO to switch the disc's sound to multi-
channel.
If an AV receiver or amplifier that is not compatible with DTS Digital
Surround is connected to the DIGITAL OUT terminal, set Digital
Output to PCM (page 42).
It is not possible to output 192 kHz or 96 kHz digital audio signals from
this player's DIGITAL OUT terminal. The signals are automatically
converted to 48 kHz or less for output.
When listening to the sound from an HDMI OUT terminal, set HDMI
Audio Out to PCM (page 43).
When listening to the sound from an DIGITAL OUT terminal, set
Digital Output to Re-encode or PCM (page 42).
When a Pioneer AV receiver or amplifier compatible with the PQLS
function is connected directly to the player's HDMI OUT terminal using
an HDMI cable, the PQLS function is activated when playing an audio
CD (CD-DA). Because of this, the sound output from components other
than the ones connected by an HDMI cable may be fast or slow. If this
happens, set Control to Off (page 43).
When a disc on which files are recorded is inserted, depending on the
number of files recorded on the disc, loading may take several dozen
minutes.
The characters that cannot be displayed on this player are displayed in
.
• Connect a USB memory device (page 22).
• Erase the data stored on the connected USB memory device from
BUDA Setup (page 47).
08
59
En