Related Manuals for Dacor RDW24
Summary of Contents for Dacor RDW24
- Page 1 Installation Instructions Renaissance Built-in Dishwasher ® Models RDW24S and RDW24I Part No. 105671 Rev. B...
-
Page 2: Table Of Contents
If You Need Help... If you have questions or problems with installation, contact your Dacor dealer or the Dacor Customer Service Team. For repairs to ® Dacor appliances under warranty call the Dacor Distinctive Service line. Whenever you call, have the model and serial number of the appliance ready. -
Page 3: Important Safety Instructions
Hazards or unsafe practices that COULD result in • Always contact the Dacor Customer Service severe personal injury or death. Team about problems and conditions that you don’t understand. See Customer Service CAUtION Information. -
Page 4: General Safety Precautions
• To prevent household mold and mildew accompanying it. A qualified service technician damage, periodically check the inlet and drain should perform all other service. Contact the hoses for leaks. nearest Dacor authorized service representative for examination, repair or adjustment. -
Page 5: Product Specifications
Epicure handle kit PN: ADWE24H Millennia handle kit PN: ADWM24H Model RDW24I requires installation of either a customer provided, custom overlay door panel or a Dacor glass Do not modify panel kit (order from your Dacor dealer). loop in hose... -
Page 6: Preparing For Installation
• The dishwasher can be connected to a cold or product data label, located inside the right door jamb. hot water supply (maximum 160°F, 70°C). Dacor Grounding Instructions for a Cord- recommends using a hot water supply of 120°F (49°C) to 140°F (60°C). If a cold water supply is... -
Page 7: Preparing The Location
*If installing model RDWH24I in a 24” wide cutout needs to be covered with an edge protector. Call installation of a trim kit (Dacor PN 106925) is required Dacor for the part number of an approved edge to fill the space between the edge of the cutout and protector. -
Page 8: Preparing For Installation
For proper drainage, the drain line connection pounds, you must order the optional heavy duty door must be a minimum of 20” (50.8 cm) above the spring kit (Dacor PN 701385). Maximum panel weight bottom of the dishwasher. with heavy duty springs: 23 pounds. - Page 9 Preparing for Installation Disposer Disposer connection connection Air gap 2” dia. max. 2” dia. max. Keep higher Keep higher than disposer than disposer 35” connection connection 35” 20” min. max. max. 20” min. Sink trap Sink trap Floor Floor Disposer Installation without Air Gap Disposer Installation with Air Gap Waste tee Waste tee...
-
Page 10: Installation Instructions
Installation Instructions Verify the Package Contents • Remove all styrofoam and plastic wrap from the dishwasher. Be sure to remove the toe kick from the top of the dishwasher packaging. With the assistance of at least one person, remove the dishwasher from the shipping pallet. -
Page 11: Installation Preparation
2 places • If installing a Dacor glass panel, install it and the handle according to the instructions included with Step 3: the glass panel kit, then skip to Leveling the Door height Dishwasher on page 11. -
Page 12: Adjust The Door Springs
Installation Instructions Custom Door Panel Installation (cont.): To make small tension adjustments to the spring, hold the back end of the spring with one Open the door slightly and use the six (6) hand and turn the front part one or more times. supplied 1 3/4”... -
Page 13: Leveling The Dishwasher
Installation Instructions Reattach the front end of the spring by pulling it Measure the height of the front and back of the up and forward to fasten it in the mount. cutout with a tape measure. Adjust the feet, until the front of the dishwasher measures 1/8”... - Page 14 Installation Instructions Connecting the Wiring Connect the ground (green) wire on the cable using a loop or spade terminal to the ground Permanently Connected Appliance Only: connection screw located on the dishwasher chassis. If the cord is not long enough, or if a hard-wire installation is needed, follow the steps below to Junction To house power...
-
Page 15: Installing The Unit In The Cabinet
Installation Instructions Water Line Connection Installing the Unit in the Cabinet Position the dishwasher in front of the cutout. CAUtION Make sure the drain hose, water supply line and power cable are positioned in the utility cutouts • The unit has a float switch in the base pan and are routed to the side they will be connected. -
Page 16: Drain Line Connection
• Repeat the Wet Test Checklist. Verifying Operation • If the appliance still does not work, contact Dacor Distinctive Service at (877) 337-3226. Do not Pre-verification Check List attempt to repair the appliance yourself. If you Confirm that the power to the dishwasher is shut need service, be sure to have the model and off at the circuit breaker panel. -
Page 17: Final Leveling
Installation Instructions Final Leveling Attaching the Anti-tip Brackets Check to make sure that adjacent drawers and CAUtION cupboards can be opened when the dishwasher door is open. Reposition the dishwasher if Make sure to anchor one anti-tip bracket on each necessary. -
Page 18: Installing The Toe Kick
• Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor dishwasher cannot be overemphasized. Toe kick □ bracket Has the unit been inspected for cosmetic... - Page 20 Item No., 80 933 28 Rev. 02 Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.com...