Sony HVRM25AU - Professional Video Cassete recorder/player Operating Instructions Manual page 17

e COMPONENT OUT jacks
Use these jacks to output component signals.
To connect a device equipped component video input
connectors, use the COMPONENT OUT jacks on the
unit. If you use the COMPONENT OUT jacks, you can
output high-quality video with less signal quality
deterioration than if you use the S VIDEO jacks.
You can set the output video format by using [HDMI/
CMPNT] of [VIDEO OUT] in the [IN/OUT REC]
menu.
When the DISPLAY OUTPUT switch is set to ALL,
text data such as time code, menu, and alarm messages
are superimposed on a monitor connected using the
COMPONENT OUT jacks (page 23).
Notes
• When images are output in 720p format, some of the
text image data (outer frame: underscan portion) on the
monitor may appear cut out. In this case, check the text
image data on the LCD monitor of the unit or on a
monitor using the S VIDEO OUT jack or the VIDEO
OUT jack. Also, when your monitor has an underscan
function, you can check all the text data on the monitor
while in underscan mode.
• The setting of [HDMI/CMPNT] of [VIDEO OUT] in
the [IN/OUT REC] menu is effective for both the
COMPONENT OUT jack and the HDMI OUT jack
(page 71).
• When you change the video format setting of [HDMI/
CMPNT] of [VIDEO OUT] in the [IN/OUT REC]
menu, the video signal output from the S VIDEO OUT
jack, VIDEO OUT jack, or HDV/DV jack may be
distorted for a moment.
• When you play back a tape in DVCAM/DV format and
while an EE picture in NTSC/PAL is displayed, either
the 480i resolution or the 576i resolution is output,
regardless of the setting of [HDMI/CMPNT] of
[VIDEO OUT] in the [IN/OUT REC] menu.
• When [HDMI/CMPNT] of [VIDEO OUT] in the [IN/
OUT REC] menu is set to either [1080i/480i] or
[1080i/576i], 1080/24p and 1080/30p video signals are
converted to 1080/60i, 1080/25p video signals are to
1080/50i, and then output.
• When you play back an HDV-formatted tape with
copyright protected signals or input HDV signals with
copyright protection to the
may be output in either 480i (NTSC) or 576i (PAL)
format, regardless of the setting of [HDMI/CMPNT]
of [VIDEO OUT] in the [IN/OUT REC] menu.
HDV/DV jack, pictures
• The output level of the COMPONENT OUT jacks is as
follows:
Output at 480i (NTSC)
With [BETACAM] selected in [480i LEVEL] of the
[IN/OUT REC] menu
Y: 1.0 Vp-p
(with 0.286 Vp-p sync negative,
output impedance 75 Ω (ohms), unbalanced)
Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 Ω (ohms), unbalanced)
(75% color bars with 7.5 IRE setup)
With [SMPTE] selected in [480i LEVEL] of the [IN/
OUT REC] menu
Y: 1.0 Vp-p
(with 0.3 Vp-p sync negative,
output impedance 75 Ω (ohms), unbalanced)
Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 Ω (ohms), unbalanced)
(100% color bars with no setup)
Output with other settings
Y: 1.0 Vp-p
(output impedance 75 Ω (ohms), unbalanced)
Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 Ω (ohms), unbalanced)
(100% color bars with no setup)
480i/480p:
Y: with 0.3 Vp-p sync negative
1080i/720p:
Y/Pb/Pr: with 0.6 Vp-p 3-level sync
f HDMI OUT jack
Use this jack to output HDMI signals. HDMI OUT jack
outputs both pictures and audio. To connect a device
equipped with HDMI input connector, use the HDMI
OUT jack on the unit.
The HDMI OUT jack outputs high-quality video with
even less signal deterioration in quality than the
COMPONENT OUT jacks.
You can set the output video format by using [HDMI/
CMPNT] of [VIDEO OUT] in the [IN/OUT REC]
menu.
Text data is superimposed on a monitor in the same way
as with a COMPONENT OUT jacks connection (page
23).
(Continued)
17
Chapter 1 Overview