Asus K8N4-E DELUXE User Manual page 47

4 . 4 . 4 . S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 [ r e d ] , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 [ r e d ] ,
4 . 4 . S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 [ r e d ] , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 [ r e d ] , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 [ r e d ] ,
S A T A _ R A I D 2 [ r e d ] , S A T A _ R A I D 3 [ r e d ] , S A T A _ R A I D 4 S A T A _ R A I D 2 [ r e d ] , S A T A _ R A I D 3 [ r e d ] , S A T A _ R A I D 4
S A T A _ R A I D 2 [ r e d ] , S A T A _ R A I D 3 [ r e d ] , S A T A _ R A I D 4 S A T A _ R A I D 2 [ r e d ] , S A T A _ R A I D 3 [ r e d ] , S A T A _ R A I D 4 S A T A _ R A I D 2 [ r e d ] , S A T A _ R A I D 3 [ r e d ] , S A T A _ R A I D 4
[ r e d ] ) [ r e d ] ) [ r e d ] )
[ r e d ] ) [ r e d ] )
These connectors are for Serial ATA signal cables. These connectors
support up to four Serial ATA hard disk drives that you can configure
as a disk array through the onboard SATA RAID controller. Refer to
Chapter 5 for details on how to set up Serial ATA RAID configurations.
These connectors are set to R A I D M o d e
connect Serial ATA boot/data hard disk drives to these connectors, set
S i l i c o n S A T A C o n t r o l l e r S i l i c o n S A T A C o n t r o l l e r
the S i l i c o n S A T A C o n t r o l l e r S i l i c o n S A T A C o n t r o l l e r item in the BIOS to [Disabled]. See S i l i c o n S A T A C o n t r o l l e r
section "4.4.3 Onboard Device Configuration" for details.
K8N4-E
®
K8N4-E DELUXE SATA RAID Connectors
• Before creating a RAID set using Serial ATA hard disks, make sure
that you have connected the Serial ATA signal cable and installed
Serial ATA hard disk drives; otherwise, you cannot enter the Silicon
Image RAID utility and SATA BIOS setup during POST.
• You can only create RAID 5 configuration using the SATALink™ SATA
RAID Management software. See Chapter 5 for details. The RAID 5
feature is not Windows
A S U S K 8 N 4 - E D e l u x e A S U S K 8 N 4 - E D e l u x e
A S U S K 8 N 4 - E D e l u x e A S U S K 8 N 4 - E D e l u x e A S U S K 8 N 4 - E D e l u x e
R A I D M o d e R A I D M o d e by default. If you want to R A I D M o d e R A I D M o d e
SATA_RAID3 SATA_RAID4
SATA_RAID1 SATA_RAID2
® Hardware Quality Labs (WHQL)-certified.
2 - 2 3 2 - 2 3
2 - 2 3 2 - 2 3 2 - 2 3