Table of Contents
Advertisement
MINOURA RDA Inter-Rim Ergo-10 / 50 Instruction manual
Please read this instructions carefully before use
(This figure is the Remote Control version)
Thank you for purchasing Minoura's Inter-Rim Ergo Trainer with RDA and Magturbo.
With its unique rim-drive system, the RDA Inter-Rim Magturbo is our most sophisticated bicycle home
trainer for both road and mountain bikes. Minoura has long been an innovator in stationary trainers, and
our new Inter-Rim trainer continues that tradition. The Rim Drive Action (RDA) system has special drive
pulleys that contact only the rim, avoiding wear and tear to the tire and any unpleasant noise. With the
RDA system, training is smoother, more adjustable, and quieter, and you avoid the cost of replacing worn-
down tires. The RDA system can handle almost any bicycle with a wheel diameter of 26 to 28 inches and
is the best trainer yet for mountain bikes.
• Read all instructions carefully before use.
• Some assembly required.
• Keep the manual handy at all times. Lost instruction materials can be replaced through
Minoura or your local dealer.
• Do NOT use trainer for any other purpose than instructed.
• The trainer is manufactured to precise standards. You may not disassemble or re-
build it.
• "Inter-Rim" and "RDA" are trademarks of Minoura and may not be copied.
- 1 -
Advertisement
Table of Contents
Related Manuals for MINOURA RDA INTERRIM ERGO
Summary of Contents for MINOURA RDA INTERRIM ERGO
- Page 1 With its unique rim-drive system, the RDA Inter-Rim Magturbo is our most sophisticated bicycle home trainer for both road and mountain bikes. Minoura has long been an innovator in stationary trainers, and our new Inter-Rim trainer continues that tradition. The Rim Drive Action (RDA) system has special drive pulleys that contact only the rim, avoiding wear and tear to the tire and any unpleasant noise.
- Page 2 Please obey warning signs. - 2 -...
- Page 3 (Fig. B) two bolts and two washers. Locate the left-side slot on the Minoura trainer. While placing the Magturbo unit at the desired position on the inside of the slot, attach it with bolts and washers by using the included hex wrench.
- Page 4 Mag unit must be assembled on the left side of RDA Trainer and the Assistant Roller Unit on the right. Do not mistake directions, see diagram for accurate placement. After deciding the height of the pulleys tighten handle securely to avoid damage to equip- (Fig.
- Page 5 Once you have set the correct position of the rim for your bicycle, you can install or remove your bicycle by rotating only one hub-clamp handle. This feature saves time. The Left-side coupling has a cut-away section to accomodate the shaft of the quick- release lever.
- Page 6 Make sure all parts have stopped spinning. Do not try to adjust the lever with your feet while riding. OPTIONS In 1998 Minoura is offering an option to the RDA Magturbo system called “ICE (Interactive Cycling Experience)” system. This computerized option will give the rider continuous automatic load changes according to pre- programmed software supplied by UltraCoach in California, U.S.A..
- Page 7 “roller replacement set”, available from your Minoura dealer. To remove: Apply a 10mm wrench to the nut behind the pulley while turning the bolt with a M4 hex wrenc h.
- Page 8 (Fig. O) MAINTENANCE AND SERVICE • If strange noises or vibration persist, discontinue use immediately and return to your Minoura dealer or place of purchase for assistance. You may also contact Minoura Co.,Ltd.: 1197-1 Godo, Anpachi, Gifu 503-2305 Japan, or contact to Minoura North American R&D Center at 1-510-739-1395.
- Page 9 350 W LOAD LEVEL OF EACH LEVER POSITION 300 W 250 W 200 W 150 W 100 W 50 W The RDA Magturbo can simulate a maximum upward slope of 4 percent. These data were measured on official testing equipment at the Japan Bicycle Technical Center. They may very according to size of the bicycle and rim and weight of the rider.
- Page 10 This magnetic resistance device is designed for usual training under 35 MPH (56 KPH) speed, so you should keep your training speed under the limit. If there is an awful noise or vibration from your magnetic resistance device during your training, please contact your purchased dealer or Minoura immediately. - 10 -...
- Page 11 REPLACEMENT PARTS You can get the following replacement parts for your Inter-Rim trainer through your local dealer; ORDER #400-1240-00 ORDER #400-1255-00 DRIVE ROLLER (MAG UNIT SIDE) 35mm DIAMETER RUBBER FOOT CAP (This part is not compatible with 1998 or older model.) ORDER #400-1243-00 ORDER #400-1241-00 COUPLING UNIT (REAR COG SIDE)
- Page 12 RESOLUTION DIAGRAM FOR MORE INFORMATION ON YOUR MINOURA TRAINER MINOURA NORTH AMERICAN CENTER FOR RESEARCH, DEVELOPMENT AND MARKETING 37653 B Argyle Rd., Fremont, CA 94536 U.S.A. Phone 510-739-1395 / Fax 510-790-1108 E-mail : MinouraUSA@IBM.net MINOURA TECHNICAL & WARRANTY CENTER Toll Free 800-601-9592 MINOURA CO., LTD.
Need help?
Do you have a question about the RDA INTERRIM ERGO and is the answer not in the manual?
Questions and answers