Dodge 2009 Dakota Owner's Manual

Dodge 2009 Dakota Owner's Manual

Dodge 2009 dakota truck owner's manual
Hide thumbs Also See for 2009 Dakota:
Table of Contents

Advertisement

2009
OWNER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2009 Dakota and is the answer not in the manual?

Questions and answers

Summary of Contents for Dodge 2009 Dakota

  • Page 1 2009 OWNER’S MANUAL...
  • Page 2: Vehicles Sold In Canada

    VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
  • Page 3: Introduction 3

    TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
  • Page 5 CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
  • Page 6: How To Use This Manual

    4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
  • Page 7 INTRODUCTION 5...
  • Page 8: Vehicle Identification Number

    The Vehicle Identification Number (VIN) is located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. VIN Location Save this label for a convenient record of your vehicle identification number and optional equipment.
  • Page 9: Vehicle Modifications/Alterations

    INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
  • Page 11: Table Of Contents

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With The Key .
  • Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Keyless Entry ....21 To Unlock The Doors ....22 To Lock The Doors .
  • Page 13 Seat Belt Extender ..... 45 Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbags ......46 Event Data Recorder (EDR) .
  • Page 14: Things To Know Before Starting Your Vehicle 9

    12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer.
  • Page 15 Ignition Switch Positions 1 — ACC 4 — ON/RUN 2 — LOCK 5 — START 3 — OFF NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become temporarily trapped in the ignition cylinder. If this occurs, rotate the THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 key to the right slightly, then remove the key as de- scribed.
  • Page 16 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. Manual Transmission — If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle.
  • Page 17: Locking Doors With The Key

    Locking Doors With The Key You can insert the key into the door lock cylinder with either side up. To lock the driver’s door, turn the key rearward. To unlock the driver’s door, turn the key forward. For external door lock lubrication, refer to “Body Lubrication”...
  • Page 18: Sentry Key Immobilizer System - If Equipped

    16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY IMMOBILIZER SYSTEM — IF EQUIPPED The Sentry Key prevents unauthorized vehicle opera- tion by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
  • Page 19: Replacement Keys

    the same key chain will not cause a key-related (transponder) fault unless the additional part is physi- cally held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system. All of the keys provided with your new vehicle have been programmed to the vehicle electronics.
  • Page 20 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the LOCK position and remove the first key.
  • Page 21: Vehicle Security Alarm System - If Equipped

    VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED The Vehicle Security Alarm system monitors the vehicle doors and ignition for unauthorized operation. When the Vehicle Security Alarm system is activated it will provide both audible and visible signals. The horn will sound repeatedly for the three minutes and the headlights and Vehicle Security Light will flash for an additional 15 min- utes.
  • Page 22: Illuminated Entry

    20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE exit alarming mode, press the RKE transmitter UNLOCK button or start the vehicle with a programmed Sentry Key . The Vehicle Security Alarm system is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly.
  • Page 23: Things To Know Before Starting Your Vehicle 21

    REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors or activate the Panic Alarm from distances up to a maxi- mum of 66 ft (20 m) using a Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.
  • Page 24: To Unlock The Doors

    22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors: Press and release the UNLOCK button on the RKE transmitter once to unlock only the driver’s door, or twice to unlock all the doors. When the unlock button is pressed, the illuminated entry will initiate, and the parking lights will flash twice.
  • Page 25 Horn Chirp Programming The horn chirp feature is shipped from the assembly plant activated. If desired, this feature can be disabled by using the following procedure: 1. Press and hold the LOCK button on the RKE trans- mitter. 2. After holding the LOCK button for four seconds, also press the PANIC button within six seconds.
  • Page 26: Using The Panic Alarm

    24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Test the Flash Lamps With Lock feature while outside of the vehicle by pressing the LOCK button on the RKE transmitter with the ignition in the OFF position and the key removed. NOTE: Pressing the LOCK button on the RKE transmit- ter while you are in the vehicle will activate the Vehicle Security Alarm.
  • Page 27: Programming Additional Transmitters

    NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. If your RKE Transmitter fails to operate from a normal distance, check for these two conditions. 1. Weak batteries in the RKE transmitter. The expected life of batteries is five years.
  • Page 28: Battery Replacement

    26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. After holding the UNLOCK button for four seconds, also press the PANIC button within six seconds. 7. When a single chime is heard, release both buttons. The chime is an indication that you have successfully entered program mode.
  • Page 29: Remote Starting System - If Equipped

    Battery Access Door 2. Remove and replace the battery. When replacing the battery, match the + sign on battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration.
  • Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Button Once the vehicle has started, the engine will run for 15 minutes. To cancel remote start, press the REMOTE START button once. The parking lights will remain illuminated to indicate that the vehicle has remote started and the engine is running.
  • Page 31: Door Locks

    The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the remote start sequence was initiated but the engine stopped cranking without starting. After either of these conditions, or if the Vehicle Security Alarm System is activated, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid key into the ignition and moving it to the RUN position, then back to...
  • Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Lock Switch If you press the power door LOCK switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle.
  • Page 33 4. Within 10 seconds, cycle the key from the LOCK position to the ON position and back to LOCK position, a minimum of four times; ending in the LOCK position. (Do not start the engine.) 5. Within 30 seconds, press the driver’s door LOCK switch in the LOCK direction.
  • Page 34: Child Protection Door Lock

    32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Within 30 seconds, press the driver’s door LOCK switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7. To reactivate the feature, repeat the above Steps. 8.
  • Page 35 To use the system, open each rear door, slide the lever up to engage the locks, and down to disengage the child- protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle, even if the inside door lock is in the unlocked position.
  • Page 36: Windows

    34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows The control on the left front door has up-down switches that give you finger-tip control of all four power win- dows. There is a single opening and closing switch on the passenger doors for passenger window control.
  • Page 37: Auto Down (Driver's Side Only)

    WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seri- ously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
  • Page 38: Occupant Restraints

    36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE windows down or partially open. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
  • Page 39: Lap/Shoulder Belts

    Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
  • Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse.
  • Page 41 plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Latch Plate To Buckle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”...
  • Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is very danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury and a belt worn under the arm can cause internal injuries.
  • Page 43 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug.
  • Page 44: Adjustable Upper Shoulder Belt Anchorage

    42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front and second row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Push in on the anchorage release button to release the anchorage, and then move it up or down to the position that fits you best.
  • Page 45: Automatic Locking Retractors (Alr) Mode - If Equipped

    The adjuster has an easy up (EZ Up) feature, which will allow it to be moved up without engaging the button. Automatic Locking Retractors (ALR) Mode – If Equipped In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt.
  • Page 46: Seat Belt Pretensioners

    44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for front outboard seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belt system in the event of a collision.
  • Page 47: Seat Belts And Pregnant Women

    NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. Chrylser LLC does not recommend deactivating BeltAlert . 1. Turn the ignition switch to the OFF position and buckle the driver’s seat belt.
  • Page 48: Driver And Right Front Passenger Supplemental Restraint System (Srs) - Airbags

    46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
  • Page 49 The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. This vehicle may also be equipped with window bags to protect the driver, and front and rear passengers sitting next to a window.
  • Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • If your vehicle is equipped with window bags, do not have any accessory items installed that will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require perma- nent attachments (bolts or screws) for installation on the vehicle roof.
  • Page 51 If a child between the ages of 1 and 12 years old, must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to Child Restraint, in this section.
  • Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • If the vehicle has window bags, they also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. Airbag System Components The airbag system consists of the following: •...
  • Page 53 position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. During a moderate-to-severe rear impact, the ORC may only deploy the seat belt pretensioners. • Also, the ORC turns on the AIRBAG warn- ing light in the instrument cluster for six to eight seconds for a self-check when the ignition is first turned on.
  • Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE may be possible based on collision severity and occu- pant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds.
  • Page 55 If a Deployment Occurs The airbag system is designed to deploy the airbags when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
  • Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, and both front seat belt retractor assemblies (w/ pretensioners), replaced by an authorized dealer as soon as possible. Maintaining Your Airbag System WARNING! •...
  • Page 57 WARNING! (Continued) • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an airbag system. NOTE: Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.
  • Page 58: Event Data Recorder (Edr)

    56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data param-...
  • Page 59 court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data, that does not identify par- ticular vehicles or crashes, may be released for incorpo- ration in aggregate crash databases, such as those main- tained by the U.S.
  • Page 60: Child Restraint

    58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status • Traction/stability control status • Tire pressure monitoring system status (if equipped). Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too. Every state in the United States, and all Canadian provinces, require that small children ride in proper restraint systems.
  • Page 61 restraint anchorage system. (Refer to “LATCH - Child Seat Anchorage System” in this section.) • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag that does not have a switch to turn the airbag Off. An airbag deployment could cause severe injury or death to infants in this position.
  • Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm.
  • Page 63 • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. • The Extended Cab first, and Club/Crew Cab second row outside seating positions, have cinching latch plates.
  • Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE connection to the top tether anchorages have been avail- able for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle.
  • Page 65 If your child restraints are not LATCH compatible, you can only install the child restraints using the vehicle’s seat belts. Refer to “Installing the LATCH-Compatible Child Restraint System” in this section. LATCH Anchors THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 LATCH Anchors Installing the LATCH-Compatible Child Restraint System —...
  • Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seatback, and are just visible when you lean into the vehicle to install the child restraint.
  • Page 67 reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.
  • Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE locking retractor seat belts, refer to Automatic Locking Mode in this section. If you have trouble tightening the lap/shoulder belt on the child restraint because, the buckle or latch plate is too close to the belt path opening on the restraint, follow these steps.
  • Page 69 WARNING! • With a child restraint installed in the rear passen- ger side locations, use care when adjusting the front seat(s) rearward, to avoid the front seatback coming in contact with the belted child directly behind the seat. The child could be injured. •...
  • Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Straps at the Rear Passenger Seat (Extended Cab) 1. Route the child restraint tether strap through the routing loop, located directly behind the child restraint. The routing loops are located behind the flip-down door on the cab back panel (padded bolster).
  • Page 71 Tether Straps at the Rear Passenger Seat (Crew Cab) 1. Route the child restraint tether strap under the head restraint for the outboard seating positions, and then through the anchor strap outer loop (webbing material loop), located directly behind the child restraint. 2.
  • Page 72: Engine Break-In Recommendations

    70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
  • Page 73: Safety Tips

    shown under “Engine Oil”, under “Maintenance Proce- dures” in section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty.
  • Page 74: Safety Checks You Should Make Inside The Vehicle

    72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace or adjust as required. Safety Checks You Should Make Inside The Vehicle Heater Defroster Ducts Inspect the heater defroster ducts for proper operation.
  • Page 75: Safety Checks You Should Make Outside The Vehicle

    Safety Checks You Should Make Outside The Vehicle Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires for proper pressure. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Lights Check the operation of all exterior lights.
  • Page 77: Understanding The Features Of Your Vehicle

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......80 Inside Day/Night Mirror ....80 Outside Mirrors .
  • Page 78 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seats ....... 115 Manual Seat Adjustment .
  • Page 79 Tilt Steering Column ....131 Electronic Speed Control — If Equipped ..132 To Activate ......133 To Set At A Desired Speed .
  • Page 80 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Garage Door Opener — If Equipped ..142 Programming HomeLink ....144 Gate Operator/Canadian Programming ..146 Using HomeLink .
  • Page 81 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Tailgate ......158 Two–Position Tailgate/Upper Load Platform .
  • Page 82: Mirrors

    80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
  • Page 83: Power Mirrors

    Power Mirrors The power mirror controls are located on the driver’s door trim panel. Power Mirror Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move.
  • Page 84: Hands-Free Communication (Uconnect ) - If Equipped

    NOTE: The UConnect system requires a cellular phone equipped with the Bluetooth Hands-Free Profile, Ver- sion 0.96 or higher. See the UConnect supported phones. NOTE: For UConnect customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect website for...
  • Page 85 • or call 1–877–855–8400 UConnect allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The UConnect system is driven through your Bluetooth “Hands-Free profile”...
  • Page 86: Operation

    84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect system is fully integrated with the vehi- cle’s audio system. The volume of the UConnect system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped.
  • Page 87 Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say Help following the beep. The UConnect system will play all the options at any prompt if you ask for help. To activate the UConnect system from idle, simply press the PHONE button and follow the audible prompts for directions.
  • Page 88 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnect system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority.
  • Page 89 • The system will prompt you to say the name of the person you want to call. • After the Ready prompt and the following beep, say the name of the person you want to call. For example, you can say John Doe, where John Doe is a previ- ously stored name entry in the UConnect phonebook or downloaded phonebook.
  • Page 90 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language.
  • Page 91 • This downloaded phonebook cannot be edited or deleted on the UConnect . These can only be edited on the mobile phone. The changes are transferred and updated to UConnect on the next phone connection. Phonebook Download — Single Entry If equipped and supported by your phone, UConnect allows the user to download entries from their phone via Bluetooth .
  • Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Phonebook Edit. • You will then be asked for the name of the phonebook entry that you wish to edit. •...
  • Page 93 from the list, press the “Voice Recognition” button while the UConnect system is playing the desired entry and say Delete. • After you enter the name, the UConnect system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete.
  • Page 94: Phone Call Features

    92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the “Voice Recognition” button during the playing of the desired name, and say Call. NOTE: The user can also exercise Edit or Delete operations at this point.
  • Page 95 call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a Second Call While Current Call in Progress To make a second call while you are currently on a call, press the “Voice Recognition”...
  • Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the PHONE button.
  • Page 97: Uconnect System Features

    • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF. UConnect System Features Language Selection To change the language that the UConnect system is using: • Press the PHONE button to begin. •...
  • Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the paired cellular phone to call the emergency num- ber. This feature is supported in the U.S., Canada, and Mexico. NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico).
  • Page 99 NOTE: • The Towing Assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). • If supported, this number may be programmable on some systems.
  • Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE numbers, followed by Send, is also to be used for navigating through an automated customer service cen- ter menu structure, and to leave a number on a pager. You can also send stored UConnect phonebook entries as tones for fast and easy access to voice mail and pager entries.
  • Page 101 Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your cell phone, the UConnect system will provide notification to inform you of your phone and network status when you are attempting to make a phone call using UConnect .
  • Page 102: Advanced Phone Connectivity

    100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Following the beep, say Mute off. Advanced Phone Connectivity Transfer Call to and from Cellular Phone The UConnect system allows ongoing calls to be trans- ferred from your cellular phone to the UConnect system without terminating the call.
  • Page 103: Things You Should Know About Your Uconnect System

    Select Another Cellular Phone This feature allows you to select and start using another phone paired with the UConnect system. • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Setup Select Phone and follow the prompts. •...
  • Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE system Voice Training feature may be used. To enter this training mode, follow one of the two following proce- dures: From outside the UConnect mode (e.g., from radio mode): • Press and hold the “Voice Recognition” button for five seconds until the session begins, or, •...
  • Page 105 • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. •...
  • Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect system.
  • Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105...
  • Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
  • Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107...
  • Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol...
  • Page 111 Voice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Voice Commands Primary Alternate(s) return to main menu return or main menu select phone...
  • Page 112: General Information

    110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • Page 113 When you press the VR hard-key, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options.
  • Page 114: Commands

    112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Recognition System understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR hard-key. 2.
  • Page 115 Radio FM To switch to the FM band say FM or RADIO FM. In this mode, you may say the following commands: • FREQUENCY (to change the frequency) • NEXT STATION (to select the next station) • PREVIOUS STATION (to select the previous station) •...
  • Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode say MEMO. In this mode, you may say the following commands: • NEW MEMO (to record a new memo) — During the recording you may press the VR hard-key to stop recording.
  • Page 117: Voice Training

    Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the UConnect system Voice Training feature may be used. 1. Press the VR hard-key, speak “System Setup” and once you are in that menu then speak “Voice Training.” This will train your own voice to the system and will improve recognition.
  • Page 118: Front Seats Manual Seat Recliners

    116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting Lever WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
  • Page 119: Manual Lumbar Support Adjustment - If Equipped

    Recline Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
  • Page 120: Adjustable Head Restraints - Front Seating Positions

    118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Adjustment Adjustable Head Restraints — Front Seating Positions Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears.
  • Page 121: Six-Way Power Seat Adjuster - Driver's Side Only

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Six-Way Power Seat Adjuster — Driver’s Side Only The power seat controls are located on the outboard side of the driver’s seat cushion. Three switches control the seat movement. The four-way switch in the center can be moved forward, backward, up, or down to adjust for the most comfortable position.
  • Page 122: Extended Cab/Crew Cab Rear Seat

    120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The seat angle can also be adjusted by using the two toggle switches, tilting it up or down. Tilt Adjustment Extended Cab/Crew Cab Rear Seat More cargo space is available by lifting up on the rear seat cushion.
  • Page 123: To Open And Close The Hood

    WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
  • Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Then push the safety latch lever up while lifting the grille with your hand. It is located at the bottom center of the grille. Secondary Latch Location Lift the hood, and the gas filled props will hold it open. To prevent possible damage, do not slam the hood to close it.
  • Page 125: Lights

    LIGHTS The headlight switch is located on the left side of the instrument panel next to the steering wheel. Headlight Switch Location Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the...
  • Page 126: Battery Saver

    124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control NOTE: Club Cab /Quad Cab models may have an optional switched dome lamp that is operated by press- ing the lens. Battery Saver To protect the life of your vehicle’s battery, Load Shed- ding is provided for both the interior and exterior lights.
  • Page 127: Headlight Delay

    Headlight Delay To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlight on for 60 seconds. This delay is initiated when the ignition is turned OFF while the headlight switch is on, and then the headlight switch is cycled off.
  • Page 128: Daytime Running Lights

    126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing.
  • Page 129: Multifunction Lever

    30 seconds when the RKE transmitter UNLOCK button is pressed, as part of the illuminated entry feature. Cargo Light Switch Multifunction Lever The multifunction lever is located on the left side of the steering column. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Turn Signals To operate the turn signals, move the multifunction lever up to signal a right-hand turn or down to signal a...
  • Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If an indicator fails to light when the multifunction lever is moved, it would suggest that the switch or indicator lamp is defective.
  • Page 131: Windshield Wipers And Washers

    High Beam/Low Beam WINDSHIELD WIPERS AND WASHERS The multifunction lever is located on the left side of the steering column. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Windshield Wipers The wipers and washers are operated by a switch in the multifunction lever.
  • Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
  • Page 133: Windshield Washers

    Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
  • Page 134: Electronic Speed Control - If Equipped

    132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
  • Page 135: To Activate

    To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates to indicate that the system is on. NOTE: The Electronic Speed Control has been designed to shut down if multiple speed control buttons (i.e., SET and CANCEL) are operated simultaneously in order to ensure proper operation.
  • Page 136: To Vary The Speed Setting

    134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary The Speed Setting When the Electronic Speed Control System is ON, the speed can be increased by pressing and holding the RESUME/ACCEL button. When the button is released, a new set speed will be established. Tapping the ACCEL button once will result in a speed increase of 1 mph (2 km/h).
  • Page 137: Overhead Console

    WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
  • Page 138: Courtesy/Reading Lights

    136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if so equipped.
  • Page 139: Us/M Button

    US/M Button Use the US/M button to change the display from U.S. to metric measurement units. US/M Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 RESET Button Use the RESET button to reset the following displays: • Average Fuel Economy •...
  • Page 140: Step Button

    138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STEP Button Use the STEP button to choose, or cycle through, the four trip conditions. STEP Button Average Fuel Economy (AVG ECO) Displays the average fuel economy since the last reset. Average fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled.
  • Page 141: Trip Odometer (Odo)

    point (fuel gauge pointer on the red “E” marker), there is reserve fuel capacity, which corresponds to approxi- mately 8% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers running out of fuel when operating at maximum load conditions in areas where there aren’t many gas stations.
  • Page 142: Global Reset

    140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE C/T Button Global Reset If the RESET button is pressed twice within two seconds while in any of the three resettable displays (AVG ECO, ODO, ET), the GLOBAL RESET will reset all three displays.
  • Page 143: Manual Compass Calibration

    NOTE: Magnetic materials should be kept away from the Overhead Console. This is where the compass sensor is located. Manual Compass Calibration NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration”...
  • Page 144: Outside Temperature

    142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Variance Map To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
  • Page 145 HomeLink Buttons NOTE: HomeLink is disabled when the Vehicle Theft Alarm is active. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
  • Page 146: Programming Homelink

    144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause seri- ous injury or death. Programming HomeLink Before You Begin The Compass Mini-Trip Computer (CMTC) illuminates the HomeLink symbol (a house with an arrow inside it)
  • Page 147 3. Simultaneously, press and hold both the chosen HomeLink button and the hand-held transmitter button until the indicator(s) change from a slow to a rapid flash rate. Then release both the HomeLink and hand-held trans- mitter buttons. It may take up to 30 seconds, or longer in rare cases. The garage door may open &...
  • Page 148: Gate Operator/Canadian Programming

    146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1 — Garage Door Opener 2 — Training Button 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn”...
  • Page 149: Using Homelink

    transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process, to prevent possible overheating of the garage door or gate motor.
  • Page 150: Security

    148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink button, for 20 seconds, until the indicator(s) starts to flash. Do not release the button. 3. Without releasing the button, proceed with PRO- GRAMMING HOMELINK , Step #2, and follow all remaining steps.
  • Page 151: Electrical Power Outlets

    2. This device must accept any interference that may be received including interference that may cause undesired operation NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device.
  • Page 152: Electrical Outlet Use With Engine Off (Battery Fed Configuration)

    150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in, draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
  • Page 153: Rear Storage - If Equipped

    Front Cup Holders – Crew Cab A two-cavity cupholder is available on all Crew Cabs , with rear seats mounted on the floor. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Rear Cup Holders – Crew Cab REAR STORAGE — IF EQUIPPED Rear Convenience Storage Crates The rear convenience storage crates are located under the rear seat lower cushion and consist of two removable,...
  • Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Open Crate 1 — Crate Handles 2 — Crate End Flaps 3 — Release Lever WARNING! Do not sit or stand on this crate. It may collapse causing serious injury. CAUTION! Do not lift up on the “End Flaps” to open the crate, damage to the “End Flaps”...
  • Page 155: Plastic Grocery Bag Retainers

    Insert Crate To install the crate into the base, insert the crate into the inboard slot and push down on the outboard side of the crate, and snap into place. To collapse the crate, push the crate end flaps inward to disengage.
  • Page 156: Floor Console - If Equipped

    154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FLOOR CONSOLE — IF EQUIPPED Floor Console Features The Floor Console between the driver’s and front pas- senger’s seat has the following features: • Miscellaneous storage compartments. • Three cupholders (two removable). • iPod/Phone storage bin. •...
  • Page 157: Rear Cargo Area Utility Rails

    inside of the armrest lid. A tissue holder is also provided on the inside of the armrest lid, which holds a pocket-size soft pack of tissue. REAR CARGO AREA UTILITY RAILS CAUTION! The maximum load per cleat should not exceed 320 lbs (145 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur.
  • Page 158: Rear Window Features

    156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To remove the cleats from the utility rail, remove the end cap by pushing up on the locking tab, located on the bottom of the end cap. Slide the cleat off the end of the rail.
  • Page 159: Sliding Rear Window - If Equipped

    prior to the time-out. The Rear Window Defroster will turn off automatically after 15 minutes from the first activation, and 10 minutes after the second activation, all within the same ignition cycle. To prevent excessive battery drain, use the rear defroster only when the engine is running.
  • Page 160: General Information

    158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE available from your authorized dealer. For safety reasons, follow all instructions on this important document. General Information The Manufacturer’s Warranty does not apply to body modifications and special equipment, such as a camper unit, heaters, stoves, refrigerators, etc., supplied by manufacturers other than Chrysler LLC.
  • Page 161 Tailgate Cable 3. Lift the tailgate off of the pivot on the passenger side by pulling upward and rearward at the same time. 4. Slide the tailgate to the passenger side while making sure clearance from the box and taillight is maintained. To reinstall the tailgate, do the following: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 1.
  • Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1 — Bulkhead Divider Slot 2 — Wheel Housing Indentions 2. Secure the tailgate in the partially-open position: 3. Open the tailgate slightly. 4. Snap the tailgate support cable between the cable guide and the tailgate bumper. Do this on both sides of the tailgate.
  • Page 163 To return the tailgate to the full-open position: 1. Lift up on the tailgate. 2. Remove both cables from between the cable guides and the tailgate bumpers, and lower the tailgate. CAUTION! • Care should always be exercised when operating a vehicle with cargo.
  • Page 165: Understanding Your Instrument Panel

    UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....166 Instrument Cluster ..... 167 Instrument Cluster Description .
  • Page 166 164 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Hands-Free Communication (UConnect ) — If Equipped ......196 Clock Setting Procedure .
  • Page 167 Operating Instructions — Satellite Mode ..223 Operating Instructions — Hands-Free Phone (If Equipped) ......226 Operating Instructions —...
  • Page 168: Instruments And Controls

    166 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS 1 - Headlight Switch 2 - Air Outlets 3 - Demister Outlets 4 - Instrument Cluster 5 - Airbags 6 - Glove Compartment 7 - Radio 8 - Climate Controls 9 - Power Outlet 10 - Heated Seat Switches* 11 - Transfer Case Switch* 12 - Speed Control Switches...
  • Page 169: Instrument Cluster

    UNDERSTANDING YOUR INSTRUMENT PANEL 167 INSTRUMENT CLUSTER...
  • Page 170: Instrument Cluster Description

    168 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge The fuel gauge shows the level of fuel in the fuel tank when ignition switch is in the ON position. 2. Temperature Gauge The temperature gauge shows engine coolant tempera- ture.
  • Page 171 5. High Beam Indicator The high beam indicator will illuminate if the headlights are on high beam. 6. Seat Belt Reminder Light The seat belt reminder light will illuminate for several seconds after the ignition is turned ON as a reminder to “buckle up.” This light will remain on as long as the seat belt remains unbuckled.
  • Page 172 170 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
  • Page 173 is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
  • Page 174 172 UNDERSTANDING YOUR INSTRUMENT PANEL CHAngE OIL and the outside temperature on vehicles that are not equipped with the Overhead Console with Compass/Temperature Mini-Trip Computer. If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, “GASCAP”...
  • Page 175 16. Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined.
  • Page 176 174 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
  • Page 177 WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD).
  • Page 178 176 UNDERSTANDING YOUR INSTRUMENT PANEL If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service. Although your vehicle will usually be drivable and not need towing, see an authorized dealer for service as soon as possible.
  • Page 179 overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
  • Page 180 178 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style.
  • Page 181: Electronic Digital Clock

    27. Cargo Light The Cargo Light indicator will illuminate when the Cargo Light is activated by pressing the CARGO LIGHT button, located on the headlight switch. 28. TOW/HAUL The TOW/HAUL button is located at the end of the gear shift lever. This light will illuminate when the TOW/ HAUL button has been selected.
  • Page 182: Sales Code Req - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)

    180 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After the hours are adjusted, push the TUNE/AUDIO control knob to set the minutes. 4. Adjust the minutes by turning the TUNE/AUDIO control knob. 5. To exit, press any button/knob, or wait approximately five seconds. SALES CODE REQ —...
  • Page 183 Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ON/VOLUME control knob to the right increases the volume and to the left decreases it.
  • Page 184 182 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button (UConnect Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect ) feature (if equipped). Refer to “Hands-Free Communication (UConnect )” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect”...
  • Page 185 RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in AM, FM or Satellite (if equipped) frequencies. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency.
  • Page 186 184 UNDERSTANDING YOUR INSTRUMENT PANEL or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast Music Type information. Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or un-...
  • Page 187 16-Digit Character Program Type Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
  • Page 188 186 UNDERSTANDING YOUR INSTRUMENT PANEL • Audio Stream – Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped). • Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped).
  • Page 189 Enter the four-digit country code using the TUNE/ SCROLL control knob to scroll up and down to select the number and then push to select. Audio Language — If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc).
  • Page 190 188 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings.
  • Page 191: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)

    Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the DVD disc does not match the region code for the radio DVD player, it will not play the disc.
  • Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc.
  • Page 193: Notes On Playing Mp3/Wma Files

    Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3/WMA file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3,WMA, DVD Video, DVD-R, DVD-RW, DVD+R, DVD+RW, and CDDA+MP3.
  • Page 194 192 UNDERSTANDING YOUR INSTRUMENT PANEL If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. Supported MP3/WMA File Formats The radio will recognize only files with the *.MP3/WMA extension as MP3/WMA files.
  • Page 195: List Button (Disc Mode For Mp3/Wma Play)

    Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files. Loading times for playback of MP3/WMA files may be affected by the following: •...
  • Page 196 194 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to elapsed time display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
  • Page 197 Operating Instructions — Voice Recognition System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in Section 3. For UConnect “Voice Recognition System (VR),” refer to “Hands-Free Communication (UConnect )” in Section 3. Operating Instructions - Hands-Free Phone (UConnect ) (If Equipped) Refer to “Hands-Free Communication (UConnect )”...
  • Page 198: Am/Fm/Cd/Dvd Multimedia System Radio (Rer/Ren) - If Equipped

    196 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM/CD/DVD MULTIMEDIA SYSTEM RADIO (RER/REN) – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER Multimedia systems contain a radio, CD/DVD player, USB port, a 20-gigabyte hard drive (HDD), and a “JukeBox”...
  • Page 199 3. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is dis- played. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing down- ward is displayed. 4.
  • Page 200: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)

    198 UNDERSTANDING YOUR INSTRUMENT PANEL Touch the screen where the words “Show Time if Radio is Off” are displayed to change the current setting. Changing the Time Zone 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen.
  • Page 201: Operating Instructions - Radio Mode

    Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
  • Page 202 200 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side Tune/Scroll control knob. Press the Tune/Scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. The clock can also be set by pressing the SETUP button. For vehicles equipped with satellite radio, press the SETUP button, use the Tune/Scroll control to select SET CLOCK, and then follow the above procedure, starting at...
  • Page 203 Push the rotary Tune/Scroll control knob a fourth time and BALANCE will display. Turn the Tune/Scroll control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary Tune/Scroll control knob a fifth time and FADE will display.
  • Page 204: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play

    202 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
  • Page 205 CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. •...
  • Page 206: Notes On Playing Mp3 Files

    204 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title. Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed.
  • Page 207 The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a number instead.
  • Page 208 206 UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rate. MPEG Specifi- Sampling Fre- cation quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio...
  • Page 209: Operation Instructions - Auxiliary Mode

    Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
  • Page 210: Operating Instructions - Radio Mode

    208 UNDERSTANDING YOUR INSTRUMENT PANEL RES/RSC Radio Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
  • Page 211 Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3. Voice Recognition Button (UConnect Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect ) feature (if equipped). Refer to “Hands-Free Communication (UConnect )”...
  • Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side Tune/Scroll control knob. Press the Tune/Scroll control knob to save time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button. For vehicles equipped with satellite radio, press the SETUP button, use the Tune/Scroll control to select SET CLOCK, and then follow the above procedure, starting at...
  • Page 213 Push the rotary Tune/Scroll control knob a third time and TREBLE will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary Tune/Scroll control knob a fourth time and BALANCE will display. Turn the Tune/Scroll control knob to the right or left to adjust the sound level from the right or left side speakers.
  • Page 214 212 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 16-Digit Character Display News Nostalga By pressing the SEEK button when the Music Type icon Oldies is displayed, the radio will be tuned to the next frequency Persnlty...
  • Page 215 Tune/Scroll control knob to adjust the minutes. Press the Tune/Scroll control knob again to save changes. AM/FM Button Press the button to select either AM or FM mode. SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button.
  • Page 216: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play

    214 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
  • Page 217 EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF.
  • Page 218: Notes On Playing Mp3 Files

    216 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next ran- domly selected track.
  • Page 219 exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator . and a three- character extension) •...
  • Page 220: List Button (Cd Mode For Mp3 Play)

    218 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Sampling Fre- Specification quency (kHz) MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
  • Page 221: Info Button (Cd Mode For Mp3 Play)

    playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds. INFO Button (CD Mode for MP3 Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available).
  • Page 222: Sound Box Operation

    220 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Hands-Free Phone (UConnect ) (If Equipped) Refer to “Hands-Free Communication (UConnect )” in Section 3. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to “Satellite Radio” in this section. SOUND BOX OPERATION The Sound Box includes one subwoofer, two tweeters and lights that pulsate with the music.
  • Page 223: Satellite Radio - If Equipped (Ren/Req/Rer/Res/Reu Radios Only)

    Switch Light Operation Position Pulse (right/passenger side) position – In this position the sound is active and the lights will pulse with the music. Pulse off/light off (center) position – In this position the sound is active but the lights will be turned off.
  • Page 224: Selecting Satellite Mode

    222 UNDERSTANDING YOUR INSTRUMENT PANEL 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Your Vehicle Identification Number. To access the ESN/SID, refer to the following steps: ESN/SID Access With REQ/RES Radios With the ignition switch in the ON/RUN or ACC posi- tion and the radio on, press the SETUP button and scroll using the Tune/Scroll control knob until Sirius ID is selected.
  • Page 225: Reception Quality

    as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle.
  • Page 226 224 UNDERSTANDING YOUR INSTRUMENT PANEL additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). INFO Button — REU Radio Pressing the INFO button will display information about Artist, Song Title, and Composer (if available).
  • Page 227 Pressing the MUSIC TYPE button again will close the MUSIC TYPE screen. Once closed, seek up, seek down, and scan will no longer be based on your selection. SETUP Button Pressing the SETUP button allows you to select the following items: •...
  • Page 228: Operating Instructions - Hands-Free Phone (If Equipped)

    226 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Hands-Free Phone (If Equipped) Refer to “Hands-Free Communication (UConnect )” in Section 3. Operating Instructions — Video Entertainment System (VES)™ (If Equipped) Refer to separate “Video Entertainment System (VES)™ Guide.” REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel.
  • Page 229: Radio Operation

    The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
  • Page 230: Radio Operation And Cellular Phones

    228 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
  • Page 231: Air Conditioning And Heater

    Air Conditioning And Heater Air Conditioning and Heater Control Air Conditioning And Heater Operation To turn on the air conditioning, set the fan control at any speed and press the SNOWFLAKE button located at the right of the control panel. Conditioned air will be di- rected through the outlets selected by the mode control.
  • Page 232 230 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Modes (Panel or Bi-Level ) Select the recirculation modes when the outside air contains dust, odors, high humidity, or if rapid cooling is desired. This feature allows for recir- culation of interior air only. Air flows either through the panel outlets or both the panel and floor outlets to- gether, depending on which recirculation mode is...
  • Page 233 Blower Control The rotary knob on the left of the control panel is the Blower Control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left position.
  • Page 234: Operating Tips

    232 UNDERSTANDING YOUR INSTRUMENT PANEL Side window demisters direct airflow specifically to the window glass to help prevent interior fogging of the glass. They are located in the extreme outside upper edges of the instrument panel. The demisters also pro- vide extra air ducts for circulation.
  • Page 235 As the temperature gets colder it may be necessary to direct air onto the windshield by using MIX Mode position on the control. Adjust the temperature control and blower speed to maintain comfort. High blower speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode.
  • Page 236: Operation Tips Chart

    234 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Tips Chart...
  • Page 237 STARTING AND OPERATING CONTENTS Starting Procedures ....239 Manual Transmission ....239 Automatic Transmission .
  • Page 238 236 STARTING AND OPERATING NV233/243 GII Transfer Case Operating Information/Precautions....251 Shifting Procedure - NV233/243 Transfer Case ......255 NV 244 Generation II Transfer Case Operating Information / Precautions .
  • Page 239 Tire Pressures For High Speed Operation ..282 Radial Ply Tires ..... . 283 Compact Spare Tire — If Equipped ..284 Limited-Use Spare —...
  • Page 240 238 STARTING AND OPERATING Flexible Fuel (4.7L Engine Only) — If Equipped . . 302 E-85 General Information ....302 Ethanol Fuel (E-85) ....304 Fuel Requirements .
  • Page 241: Starting Procedures

    STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat buildup may cause serious injury or death. Manual Transmission Apply the parking brake, place the shift lever in NEU- TRAL and depress clutch pedal to the floor before...
  • Page 242: Starting And Operating

    240 STARTING AND OPERATING Normal Starting NOTE: Normal starting of either a warm or cold engine is obtained without pumping or depressing the accelera- tor pedal. Turn the ignition switch to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure.
  • Page 243: After Starting

    If the engine fails to start after you have followed the normal starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel, in case the engine is flooded.
  • Page 244: Manual Transmission

    242 STARTING AND OPERATING WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. MANUAL TRANSMISSION WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied.
  • Page 245: Shifting

    Shifting Shift Pattern Fully depress the clutch pedal before shifting gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. You should always use 1st gear when starting from a standing position. STARTING AND OPERATING 243 Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in recommended shift speed chart.
  • Page 246: Downshifting

    244 STARTING AND OPERATING Downshifting Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed.
  • Page 247: Reverse Shifting

    Gear Selec- 6 to 5 5 to 4 4 to 3 tion Maxi- 85 mph 75 mph 55 mph (135 (120 Speed km/h) km/h) km/h) Reverse Shifting To shift into REVERSE, bring the vehicle to a complete stop. Depress the clutch and pause briefly to allow the gear train to stop rotating.
  • Page 248: Brake/Transmission Interlock System

    246 STARTING AND OPERATING CAUTION! (Continued) • Before shifting into any gear, make sure your foot is firmly on the brake pedal. WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed.
  • Page 249 the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever into the PARK position. WARNING! • Never use PARK position on an automatic trans- mission as a substitute for the parking brake. Always apply the parking brake fully, when parked, to guard against vehicle movement and possible injury or damage.
  • Page 250 248 STARTING AND OPERATING 1 (First) For driving up very steep hills and for engine braking at low speeds, 25 mph (40 km/h) or less, when going down hill, use 1st gear. To prevent excessive engine speed do not exceed 25 mph (40 km/h) in this range. Overdrive Operation The Overdrive automatic transmission contains an electronically-controlled 4th and 5th (if equipped) gear...
  • Page 251 If the transmission temperature gets extremely hot, the transmission will automatically select the most desirable gear for operation at this temperature. If the transmission temperature becomes hot enough, the “Trans Temp” light may illuminate and the transmission may downshift out of Overdrive until the transmission cools down.
  • Page 252 250 STARTING AND OPERATING operating in TOW/HAUL mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy), and auto- matic closed-throttle downshifts to 3rd gear (for im- proved braking) will occur during steady braking.
  • Page 253: Four-Wheel Drive Operation

    cause damage to the transmission. The torque converter will refill within five seconds of shifting from PARK into any other gear position. FOUR-WHEEL DRIVE OPERATION NV233/243 GII Transfer Case Operating Information/Precautions The NV233/243 is an electric-shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel.
  • Page 254 252 STARTING AND OPERATING Transfer Case Position Indicator Lights Transfer case position indicator lights are located on the instrument cluster. If there is no indicator light on or flashing, the transfer case position is in two-wheel drive (2WD). If the indicator light is on, the desired position (4WD LOCK and 4WD LOW) has been obtained.
  • Page 255 When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h).
  • Page 256 254 STARTING AND OPERATING For additional information on the appropriate use of each transfer case mode position, refer to the following infor- mation: The 2–Wheel Drive (Rear-Wheel Drive) High Range is used for normal street and highway driving, on dry, hard-surfaced roads.
  • Page 257: Shifting Procedure - Nv233/243 Transfer Case

    Shifting Procedure - NV233/243 Transfer Case NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift, the indicator light for the previous position will remain ON, and the newly-selected position indica- tor light will continue to flash until all the requirements for the selected position have been met.
  • Page 258 256 STARTING AND OPERATING will remain ON. At this time, reduce speed and stop spinning the wheels to complete the shift. There may be a delay up to 10 seconds for the shift to complete after the wheels have stopped spinning. 4WD LOCK-to-4WD LOW or 4WD LOW-to-4WD LOCK NOTE: When shifting into or out of 4WD LOW, some...
  • Page 259: Nv 244 Generation Ii Transfer Case Operating Information / Precautions

    4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). NOTE: If steps 1 or 2, of either the Preferred or Alternate Procedure, are not satisfied prior to attempting the shift, or if they no longer are being met while the shift attempt is in process, then the indicator light will flash and the current transfer case position will be maintained.
  • Page 260 258 STARTING AND OPERATING roads. This feature provides the safety, security, and convenience of operating in all-wheel drive at all times regardless of road conditions. When additional traction is required, the 4WD LOCK and 4WD LOW positions can be used to lock the front and rear driveshafts together, through the transfer case inter-axle differential, and force the front and rear wheels to rotate at the same speed.
  • Page 261 WARNING! Always engage the parking brake when powering down the vehicle if the SVC 4WD light is illumi- nated. Not engaging the parking brake may allow the vehicle to roll, which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning.
  • Page 262 260 STARTING AND OPERATING For additional information on the appropriate use of each transfer case mode position, refer to the following infor- mation: The 4-Wheel Drive High Range employs the inter-axle differential. This range allows front and rear wheels to rotate at different speeds on all road surfaces.
  • Page 263: Transfer Case

    Shifting Procedure - NV 244 Generation II Transfer Case NOTE: The 4x4 system will not allow shifts between 4WD/4WD LOCK if the rear wheels are spinning (no traction). In this situation, a position indicator light will flash and the original position indicator light will remain on.
  • Page 264: Limited-Slip Rear Axle Differential - If Equipped

    262 STARTING AND OPERATING 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the position indicator light has stopped flashing, shift the transmission back into gear. Alternate Procedure 1. Bring the vehicle to a complete stop. 2.
  • Page 265: Driving On Slippery Surfaces

    WARNING! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface.
  • Page 266: Driving Through Water

    264 STARTING AND OPERATING DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off).
  • Page 267 CAUTION! (Continued) • Driving through standing water may cause dam- age to your vehicle’s drivetrain components. Al- ways inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of con- tamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water.
  • Page 268: Power Steering

    266 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle.
  • Page 269: Parking Brake

    apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized dealer. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill.
  • Page 270 268 STARTING AND OPERATING Parking Brake Be sure the parking brake is firmly set when parked and the shift lever is in the PARK position (automatic trans- mission), or REVERSE, or 1st gear (manual transmission). When parking on a hill, you should apply the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK.
  • Page 271: Brake System

    When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should be applied whenever the driver is not in the vehicle. BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function.
  • Page 272: Four-Wheel Anti-Lock Brake System (Abs)

    270 STARTING AND OPERATING WARNING! Both Anti-Lock Brake Systems contain sophisticated electronic equipment. It may be susceptible to inter- ference caused by improperly installed or high out- put radio transmitting equipment. This interference can cause possible loss of anti-lock braking capabil- ity.
  • Page 273 WARNING! • Anti-Lock Brake Systems (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
  • Page 274: Tire Safety Information

    272 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 1 — U.S. DOT Safety Stan- 4 — Maximum Load dards Code (TIN) 2 — Size Designation 5 — Maximum Pressure 3 — Service Description 6 — Treadwear, Traction and Temperature Grades NOTE: •...
  • Page 275 Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- tion. Example: T145/80D18 103M. Tire Sizing Chart Size Designation: P = Passenger Car tire size based on U.S. design standards ...blank... = Passenger Car tire based on European design standards LT = Light Truck tire based on U.S.
  • Page 276 274 STARTING AND OPERATING 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
  • Page 277: Tire Identification Number (Tin)

    Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. DOT = Department of Transportation —...
  • Page 278: Tire Loading And Tire Pressure

    276 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar. Tire and Loading Information Placard Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
  • Page 279 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading...
  • Page 280 278 STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
  • Page 281 STARTING AND OPERATING 279...
  • Page 282: Tires - General Information

    280 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
  • Page 283: Tire Inflation Pressures

    WARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread.
  • Page 284: Tire Pressures For High Speed Operation

    282 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
  • Page 285: Radial Ply Tires

    loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail.
  • Page 286: Compact Spare Tire - If Equipped

    284 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
  • Page 287: Tire Spinning

    vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity. WARNING! The limited-use spare tires are for emergency use only.
  • Page 288: Tread Wear Indicators

    286 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves.
  • Page 289: Replacement Tires

    WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible.
  • Page 290: Alignment And Balance

    288 STARTING AND OPERATING WARNING! • DO NOT use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
  • Page 291: Supplemental Tire Pressure Information - If Equipped

    Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your authorized dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance.
  • Page 292 290 STARTING AND OPERATING CAUTION! (Continued) • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Bro- ken chains can cause serious vehicle damage. Stop the vehicle immediately if noise occurs that could suggest chain breakage.
  • Page 293: Snow Tires

    CAUTION! • Do not use tire chains on vehicles equipped with tires other than P245/70R16. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. • Do not use tire chains on the front wheels of your vehicle.
  • Page 294: Tire Pressure Monitor System (Tpms) - If Equipped

    292 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
  • Page 295 TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects, or natural pressure loss through the tire. The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recom- mended cold placard pressure.
  • Page 296 294 STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
  • Page 297: Base System - If Equipped

    • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in the tire. Base System – If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
  • Page 298 296 STARTING AND OPERATING fault condition no longer exists. A system fault can occur by any of the following scenarios: 1) Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors; 2) Installing some form of aftermarket window tinting that affects radio wave signals;...
  • Page 299: General Information

    General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
  • Page 300: Reformulated Gasoline

    298 STARTING AND OPERATING Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.
  • Page 301: Usage In Non-Flex Fuel Vehicles

    CAUTION! DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline or E85 Ethanol blends are not the responsibility of the manufacturer.
  • Page 302: Mmt In Gasoline

    300 STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles.
  • Page 303 CAUTION! (Continued) • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service.
  • Page 304: Carbon Monoxide Warnings

    302 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill.
  • Page 305 manual for information on features that are common between Flexible Fuel and gasoline-only powered ve- hicles. E-85 Fuel Cap STARTING AND OPERATING 303 CAUTION! Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85. E-85 Badge...
  • Page 306: Ethanol Fuel (E-85)

    304 STARTING AND OPERATING ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
  • Page 307: Selection Of Engine Oil For Flexible Fuel

    Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles FFV vehicles operated on E-85 require specially formu- lated engine oils. These special requirements are included in MOPAR engine oils, and in equivalent oils meeting Chrysler Specification MS-6395. The manufacturer only recommends engine oils that are API Certified and meet the requirements of Material Standard MS-6395.
  • Page 308: Adding Fuel

    306 STARTING AND OPERATING CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door. When fueling, the cap may be placed on the inside of the filler door.
  • Page 309 CAUTION! Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. WARNING! • Never allow any lit smoking materials near the vehicle while removing the cap or filling the tank.
  • Page 310: Vehicle Loading

    308 STARTING AND OPERATING VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door. Certification Label This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN).
  • Page 311: Curb Weight

    Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded. Each axle GAWR is determined by the component in the system with the lowest load carrying capacity (axle, springs, tires, or wheels).
  • Page 312: Trailer Towing

    310 STARTING AND OPERATING should then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.
  • Page 313: Common Towing Definitions

    Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR.
  • Page 314 312 STARTING AND OPERATING Trailer Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer is the tongue weight. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle.
  • Page 315 STARTING AND OPERATING 313 WARNING! An improperly adjusted weight-distributing hitch may reduce handling, stability, and braking perfor- mance, and could result in an accident. Weight-Distributing Systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recreational vehicle dealer for additional information.
  • Page 316 314 STARTING AND OPERATING EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of Weight- Distributing Hitch (Incorrect)
  • Page 317: Trailer Hitch Classification

    Trailer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alter- ations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package.
  • Page 318: Trailer Towing Weights (Maximum Trailer Weight Ratings)

    • http:// www.dodge.com/towing • http:// www.dodge.ca (Canada) Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
  • Page 319: Towing Requirements

    • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
  • Page 320 318 STARTING AND OPERATING WARNING! (Continued) Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
  • Page 321 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight.) Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire.
  • Page 322 320 STARTING AND OPERATING CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances.
  • Page 323 4-Pin Connector 1 — Female Pins 4 — Park 2 — Male Pin 5 — Left Stop/Turn 3 — Ground 6 — Right Stop/Turn STARTING AND OPERATING 321 7-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 —...
  • Page 324: Towing Tips

    322 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in 1st gear to avoid excessive clutch slippage.
  • Page 325: Snowplow

    − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can resume cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency. Towing Tips — Cooling System To reduce potential for engine and transmission over- heating, take the following actions: −...
  • Page 326: Recreational Towing (Behind Motorhome, Etc.)

    324 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) 2WD Models Recreational towing of 2WD models is not allowable. Towing the vehicle with the transmission in NEUTRAL can cause severe transmission damage. Removal of the driveshaft for towing is not recommended, since this would allow fluid to drain from the transmission.
  • Page 327 Recreational Towing Procedure Use the following procedure to prepare your vehicle for recreational towing. CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts. 1.
  • Page 328 326 STARTING AND OPERATING 9. Shift automatic transmission into REVERSE. 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 11. Repeat steps 9 and 10 with the transmission in DRIVE. 12. Shut engine OFF and place ignition key to the unlocked OFF position.
  • Page 329 CAUTION! Damage to the transmission may occur if the trans- mission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL, ensure that the engine is off prior to shifting the transmission into PARK. Returning to Normal Operation Use the following procedure to prepare your vehicle for normal usage.
  • Page 330 328 STARTING AND OPERATING NOTE: • Steps 1 through 5 are requirements that must be met prior to depressing the NEUTRAL selection button, and must continue to be met until 1 second elapses and the shift has been completed. If any of these requirements (with the exception of 3 - key ON) are not met prior to depressing the NEUTRAL button or are no longer met during the 1 second time, then all of...
  • Page 331 CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage internal parts. STARTING AND OPERATING 329...
  • Page 333: What To Do In Emergencies

    WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....332 Changing A Flat Tire ....332 Jack Location .
  • Page 334: Hazard Warning Flasher

    332 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning Flasher switch is located on the top of the steering column, just behind the steering wheel. Hazard Warning Flasher Switch Press the switch and all front and rear directional signals will flash intermittently.
  • Page 335 WHAT TO DO IN EMERGENCIES 333 The jack is secured in place by turning the jack screw until the jack is secured into place. A finger-operated helper tool is provided to assist re- moval and stowage of the jack. This tool must be removed to operate the jack for changing the spare tire.
  • Page 336: Removing The Spare Tire

    334 WHAT TO DO IN EMERGENCIES Jack Stowage Location (Crew Cab) WARNING! The jack is designed as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure.
  • Page 337 Steps for Removing the Spare Tire • Remove the jack from the stowage compartment using the supplied finger-assist tool. • Remove the finger-assist tool from jack and set aside until jack is stowed. • Assemble the jack tools. • Locate the tire carrier access hole on the rear bumper. •...
  • Page 338 336 WHAT TO DO IN EMERGENCIES Turning Lug Wrench and Extension It is recommended that you stow the flat or spare to avoid tangling the loose cable. Spare Tire Stowage Location NOTE: The winch mechanism is designed for use with the jack extension tube only.
  • Page 339: Tire Changing Procedure

    Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
  • Page 340: Instructions

    338 WHAT TO DO IN EMERGENCIES 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
  • Page 341 WARNING! (Continued) • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated are securely stowed, spares must be stowed with the valve stem facing the ground. • Turn on the Hazard warning flasher. Jack Warning Label 1.
  • Page 342 340 WHAT TO DO IN EMERGENCIES Positioning of the Jack Front Wheels Left Rear Jacking Location 4. When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle in the positions shown with the drive tubes extending to the rear.
  • Page 343 Right Rear Jacking Location NOTE: Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 5. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WHAT TO DO IN EMERGENCIES 341 WARNING! Raising the vehicle higher than necessary can make...
  • Page 344 342 WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Al- ways stow the jack, tools and the extra tire and wheel in the places provided. 8.
  • Page 345: To Stow The Flat Or Spare

    To Stow the Flat or Spare Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle.
  • Page 346 344 WHAT TO DO IN EMERGENCIES If the indicator is dark or shows a green dot, proceed as follows: 1. Wear eye protection and remove all metal jewelry such as watch bands or bracelets, which might make an unintended electrical contact. 2.
  • Page 347 WARNING! (Continued) • During cold weather when temperatures are be- low freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting jump-start. 6.
  • Page 348: Freeing A Stuck Vehicle

    346 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the shift lever rhythmically between FIRST and REVERSE, while apply- ing slight pressure to the accelerator. The least amount of accelerator pedal pressure to main- tain the rocking motion without spinning the wheels or racing the engine is most effective.
  • Page 349: Towing A Disabled Vehicle

    WARNING! • Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road.
  • Page 350: Two-Wheel Drive Vehicles

    348 WHAT TO DO IN EMERGENCIES Two-Wheel Drive Vehicles Provided that the transmission is operable, tow with the transmission in NEUTRAL and the ignition key in the OFF position, along with the front wheels raised and the rear wheels on the ground. The speed must not exceed 30 mph (50 km/h), and the distance must not exceed 15 miles (25 km).
  • Page 351: Maintaining Your Vehicle

    MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 3.7L ... . . 351 Engine Compartment — 4.7L ... . . 352 Onboard Diagnostic System —...
  • Page 352 350 MAINTAINING YOUR VEHICLE Exhaust System ..... . 363 Cooling System ..... . 366 Brake System .
  • Page 353: Engine Compartment - 3.7L

    ENGINE COMPARTMENT — 3.7L 1 — Air Cleaner Filter 2 — Automatic Transmission Dipstick 3 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 5 — Clutch Fluid Reservoir (Manual Transmission Only) 6 — Power Distribution Center MAINTAINING YOUR VEHICLE 351 7 —...
  • Page 354: Engine Compartment - 4.7L

    352 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 4.7L 1 — Air Cleaner Filter 2 — Automatic Transmission Dipstick 3 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 5 — Power Distribution Center 6 — Battery 7 — Engine Oil Fill 8 —...
  • Page 355: Onboard Diagnostic System - Obd Ii

    ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
  • Page 356: Emissions Inspection And Maintenance Programs

    354 MAINTAINING YOUR VEHICLE problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL off.
  • Page 357: Replacement Parts

    5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
  • Page 358: Dealer Service

    356 MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service person- nel, special tools and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself.
  • Page 359 Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Always maintain the oil level within the SAFE zone on the dipstick. Adding one quart/liter of oil when the reading is at the bottom of the SAFE zone will result in a reading at the top of the safe zone on these engines.
  • Page 360: Engine Oil Filter

    358 MAINTAINING YOUR VEHICLE The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to “Engine Compart- ment” in this section. Lubricants which do not have both the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used.
  • Page 361: Engine Air Cleaner Filter

    Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance.
  • Page 362: Air Conditioner Maintenance

    360 MAINTAINING YOUR VEHICLE WARNING! (Continued) • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other.
  • Page 363: Drive Shaft Constant Velocity Joints

    include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you.
  • Page 364: Body Lubrication

    362 MAINTAINING YOUR VEHICLE could result in failure of the joint due to water, and dirt contamination of the grease. This would require com- plete replacement of the joint assembly. Refer to the Service Manual for the detailed replacement procedure. Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate,...
  • Page 365: Windshield Washers

    Windshield Washers The fluid reservoir should be checked for fluid level at regular intervals. When freezing weather is anticipated, flush out the water in the reservoir by operating the system. Fill the reservoir with windshield washer anti- freeze (not radiator antifreeze), and operate the system for a few seconds to flush out the residual water.
  • Page 366 364 MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, fol- low the preceding safety tips. The catalytic converter requires the use of unleaded fuel only.
  • Page 367 WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
  • Page 368: Cooling System

    366 MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.
  • Page 369 rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution. Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. Selection Of Coolant Use only the manufacturer’s recommended engine cool- ant (antifreeze). Refer to “Fluids, Lubricants, and Genu- ine Parts”...
  • Page 370 368 MAINTAINING YOUR VEHICLE Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze). When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water.
  • Page 371 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
  • Page 372 370 MAINTAINING YOUR VEHICLE of this. As long as the engine operating temperature is satisfactory, the coolant recovery bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant recovery bottle.
  • Page 373: Brake System

    • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, also keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat.
  • Page 374: Clutch Hydraulic System

    372 MAINTAINING YOUR VEHICLE Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture. CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance-free system.
  • Page 375 To check the automatic transmission fluid level properly, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake and press the brake pedal.
  • Page 376 374 MAINTAINING YOUR VEHICLE CAUTION! Be aware that if the fluid temperature is below 50° F (10° C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7.
  • Page 377: Transfer Case

    CAUTION! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid, other than the manufacturer’s recommended fluid, will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts”...
  • Page 378: Appearance Care And Protection From Corrosion

    376 MAINTAINING YOUR VEHICLE components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. Lubricant Selection Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
  • Page 379 The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR Car Wash or a mild car wash soap, and rinse the panels completely with clear water.
  • Page 380 378 MAINTAINING YOUR VEHICLE Special Care • If you drive on salted or dusty roads, or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels be kept clear and open.
  • Page 381 YES Essentials Fabric Cleaning Procedure – if equipped YES Essentials seats may be cleaned in the following manner: • Remove as much of the stain as possible by blotting with a clean, dry towel. • Blot any remaining stain with a clean, damp towel. •...
  • Page 382 380 MAINTAINING YOUR VEHICLE Stubborn soils can be removed easily with a soft cloth and MOPAR Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia-based cleaners to clean your leather upholstery.
  • Page 383: Fuses

    Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
  • Page 384 382 MAINTAINING YOUR VEHICLE Power Distribution Center This center contains cartridge fuses, mini fuses and relays. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity num- ber of each fuse is stamped on the inside cover that corresponds to the following chart.
  • Page 385 Cartridge Mini- Cavity Fuse Fuse 10 Amp Cabin Compartment Node (CCN)/Mirror/ Spare 2 Amp Low Current Ignition Gray Switch 10 Amp AC Clutch 15 Amp Trailer Tow Lt Stop/ Blue Turn 15 Amp Trailer Tow Rt Stop/ Blue Turn 20 Amp Ignition Off Draw Yellow (IOD) #2...
  • Page 386 384 MAINTAINING YOUR VEHICLE Cartridge Mini- Cavity Fuse Fuse 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 20 Amp Yellow 10 Amp 20 Amp Yellow 20 Amp Yellow Description Cavity Fog Lamps Powertrain Control Module (PCM) B+ Cabin Compartment Node (CCN) Illumi- nation Ignition Run/Start...
  • Page 387 Cartridge Mini- Cavity Fuse Fuse 30 Amp Starter Solenoid Pink 40 Amp Ignition Run Feeds Green 30 Amp Wiper Motor Pink 25 Amp Front Control Module Natural (FCM) 5 (T-Case) 10 Amp Lt Park Lamps 10 Amp Rt Park Lamps 20 Amp Trailer Tow Park Yellow...
  • Page 388: Vehicle Storage

    386 MAINTAINING YOUR VEHICLE Cartridge Mini- Cavity Fuse Fuse 10 Amp 20 Amp Yellow 20 Amp Yellow 10 Amp 10 Amp 20 Amp Yellow VEHICLE STORAGE Description If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- Heated Seats mize the drain on your vehicle’s battery: •...
  • Page 389: Replacement Light Bulbs

    REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Dome Light ......WL212–2 Cargo Light ......921 Overhead Console Lights .
  • Page 390 388 MAINTAINING YOUR VEHICLE 3. Grasp the headlight and pull firmly to disengage the headlight housing from the fender panel. 4. While firmly holding the headlight housing in your hands, unlock and disconnect headlight bulb connector. 5. Twist 1/4-turn and remove headlight bulb from hous- ing and replace.
  • Page 391: Rear Side Marker, Taillamps/Stop Lamps

    MAINTAINING YOUR VEHICLE 389 Rear Side Marker, Taillamps/Stop Lamps, And 2. Pull the taillamp housing straight out from the body. Turn Signal Bulbs — Replacement 1. Remove the two screws that pass through the bed sheet metal.
  • Page 392 390 MAINTAINING YOUR VEHICLE 3. Rotate the bulb socket counterclockwise to remove it 4. Pull bulb straight out of socket. from the housing.
  • Page 393: Center High-Mounted Stop Light And Cargo

    5. Reverse this procedure to install bulb and housing. Place the two raised blocks past the body. MAINTAINING YOUR VEHICLE 391 Center High-Mounted Stop Light And Cargo Lamp 1. Remove the two screws holding the housing/lens to the body, as shown.
  • Page 394 392 MAINTAINING YOUR VEHICLE 2. Remove housing from the cab. 3. Remove connector from housing tab for more clearance.
  • Page 395 4. Turn desired bulb socket 1/4-turn and remove socket and bulb from housing. MAINTAINING YOUR VEHICLE 393 5. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mounted Stop Light 6. Reverse this procedure for installation of bulbs and housing.
  • Page 396: License Lamps

    394 MAINTAINING YOUR VEHICLE License Lamps 2. Rotate the socket 1/4-turn counterclockwise. 1. Using a screwdriver, pry black rubber housing from the bumper.
  • Page 397: Fog Lights

    3. Pull bulb from socket. 4. Reverse this procedure for installation. MAINTAINING YOUR VEHICLE 395 Fog Lights 1. Disconnect connector from fog light by raising the wire harness lock tab and pulling on wire harness connector. 2. Rotate fog light bulb 1/4-turn counterclockwise and pull to remove from fog light housing.
  • Page 398: Fluids And Capacities

    396 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.7L Engine (SAE 5W-20, API Certified) 4.7L/4.7L HO Engine (SAE 5W-20, API Certified) Cooling System (Includes 2.1 Quarts/2 Liters for Cool- ant Bottle) 3.7L Engine (MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L/4.7L HO Engine (MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula)
  • Page 399: Fluids, Lubricants And Genuine Parts

    FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs (3.7L Engine) Spark Plugs (4.7L Engine) Fuel Selection 3.7L/4.7L Fuel Selection 4.7L HO Fluid, Lubricant, or Genuine Part MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
  • Page 400: Chassis

    398 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Manual Transmission (Getrag 238) Clutch Linkage Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid MOPAR ATF+4 Automatic Transmission Fluid MOPAR ATF+4 Automatic Transmission Fluid Multi-Purpose Grease, NLGI Grade 2 E.P.
  • Page 401: Maintenance Schedules

    MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..400 Maintenance Schedule ....400 Required Maintenance Intervals ..402...
  • Page 402: Emissions Control System Maintenance

    400 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Con- trol System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
  • Page 403 • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change.
  • Page 404 402 MAINTENANCE SCHEDULES At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. • Check the manual transmission fluid level. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals NOTE: ** Vehicles built with the 4.7L engine are...
  • Page 405 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule Change the engine oil and engine oil filter.
  • Page 406 404 MAINTENANCE SCHEDULES 18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Inspect the front and rear axle fluid, change if you are using your vehicle for police, taxi, fleet, off-road, or frequent trailer towing.
  • Page 407: Service Schedule

    30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (3.7L engines). Replace the top row of spark plugs (4.7L engines). ** Inspect the transfer case fluid.
  • Page 408 406 MAINTENANCE SCHEDULES 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. Inspect the brake linings, replace if necessary.
  • Page 409 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the ignition cables (3.7L engine). Replace the spark plugs (3.7L engines). Replace the top row of spark plugs (4.7L engines). ** Inspect the brake linings, replace if necessary.
  • Page 410 408 MAINTENANCE SCHEDULES 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Odometer Reading Repair Order # Dealer Code Signature Authorized Chrysler Dealer 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule Change the engine oil and engine oil filter.
  • Page 411 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule Change the engine oil and engine oil filter.
  • Page 412 410 MAINTENANCE SCHEDULES 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (3.7L engines). Replace the top row of spark plugs (4.7L engines). ** Inspect and replace PCV valve, if necessary.
  • Page 413 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. Inspect the brake linings, replace if necessary.
  • Page 414 412 MAINTENANCE SCHEDULES 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary.
  • Page 415 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the ignition cables (3.7L engine). Replace the spark plugs (3.7L engines). Replace the top row of spark plugs (4.7L engines). ** Inspect the brake linings, replace if necessary.
  • Page 416 414 MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Inspect the front and rear axle fluid, change if you are using your vehicle for police, taxi, fleet, off-road, or frequent trailer towing.
  • Page 417 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. Inspect the brake linings, replace if necessary.
  • Page 418 416 MAINTENANCE SCHEDULES WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
  • Page 419: If You Need Consumer Assistance

    IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......419 Prepare For The Appointment .
  • Page 420 418 IF YOU NEED CONSUMER ASSISTANCE Chrysler Canada Inc. Customer Center ..424 In Mexico Contact ....424 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) .
  • Page 421: Suggestions For Obtaining Service For Your

    SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
  • Page 422: Mopar Parts

    420 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from an authorized dealer. They will help keep the vehicle operating at its best. REPORTING SAFETY DEFECTS In The 50 United States And Washington, D.C. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety...
  • Page 423: Publication Order Forms

    PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals (no P.O.
  • Page 424: Department Of Transportation Uniform Tire

    422 IF YOU NEED CONSUMER ASSISTANCE Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the Worldwide Web at: • www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration.
  • Page 425: Temperature Grades

    WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
  • Page 426: Chrysler Llc Customer Center

    424 IF YOU NEED CONSUMER ASSISTANCE and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer’s service manager first.
  • Page 427: In Mexico Contact

    In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico City: 5081-4568 Outside Mexico City: 1-800-505-1300 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its customer center.
  • Page 428 426 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience.
  • Page 429 INDEX...
  • Page 430 428 INDEX Adding Fuel ......306 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 359 Air Conditioner Maintenance .
  • Page 431 Battery ....... 359 Charging ......343 Emergency Starting .
  • Page 432 430 INDEX Chart, Tire Sizing ......273 Check Engine Light (Malfunction Indicator Light) ....... . 354 Child Restraint .
  • Page 433 Data Recorder, Event ..... . 56 Daytime Running Lights ....126 Dealer Service .
  • Page 434 432 INDEX Exhaust Gas Caution ....71,302 Flooded, Starting ..... . 240 Fuel Requirements .
  • Page 435 Fluid Level Checks Automatic Transmission ....372 Brake ....... 371 Engine Oil .
  • Page 436 434 INDEX Gross Axle Weight Rating ....309,311 Gross Cargo Weight ..... . 308 Gross Vehicle Weight Rating .
  • Page 437 Intermittent Wipers (Delay Wipers) ... 130 Introduction ......4 Jack Operation .
  • Page 438 436 INDEX Lights On Reminder ....126 Low Fuel ......168 Malfunction Indicator (Check Engine) .
  • Page 439 Electric Powered ..... . . 81 Outside ......80 Rearview .
  • Page 440 438 INDEX Parking Brake ......267 Parking On Hill ......267 Passing Light .
  • Page 441 Recorder, Event Data ..... . 56 Recreational Towing ..... . 324 Shifting into Transfer Case Neutral (N) .
  • Page 442 440 INDEX Seats ....... . . 115 Adjustment ......115 Cleaning .
  • Page 443 Emergency (Jump Starting) ....343 Engine Block Heater ....241 Engine Fails to Start .
  • Page 444 442 INDEX High Speed ......282 Inflation Pressures ..... 281 Jacking .
  • Page 445 Transaxle ......245 Automatic ......12,245 Manual .
  • Page 446 444 INDEX Warning Lights (Instrument Cluster Description) ......168 Warnings and Cautions ..... 6 Warranty Information .
  • Page 447 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key RemovalLocking Doors With The KeySTEERING WHEEL LOCK - IF EQUIPPED If You Wish To Manually Lock The Steering WheelTo Release The Steering Wheel LockAutomatic Transmission Ignition Interlock SystemSENTRY KEY IMMOBILIZER SYSTEM - IF EQUIPPED Replacement KeysCustomer Key ProgrammingVEHICLE SECURITY ALARM SYSTEM - IF EQUIPPED To Set the AlarmTo Disarm the SystemILLUMINATED ENTRY Vehicles Equipped With Power Door LocksREMOTE KEYLESS ENTRY To Unlock The DoorsTo Lock The DoorsUsing The Panic AlarmGeneral InformationProgramming Additional TransmittersBattery ReplacementREMOTE STARTING SYSTEM - IF EQUIPPED DOOR LOCKS Manual Door LocksPower Door LocksChild Protection Door LockWINDOWS Power WindowsAuto Down (Drivers Side Only)Window Lockout SwitchWind BuffetingOCCUPANT RESTRAINTS Lap/Shoulder BeltsAdjustable Upper Shoulder Belt AnchorageAutomatic Locking Retractors (ALR) Mode - If EquippedCenter Lap BeltsSeat Belt Pretensioners...
  • Page 448: Installation Of Radio Transmitting Equipment

    INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
  • Page 449 Chrysler LLC 81-326-0934 First Edition Printed in U.S.A.

This manual is also suitable for:

2009 nd dakota

Table of Contents

Save PDF