Pioneer XDV-P6 - DVD Changer - in-dash Installation Manual

XDV-P6
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Japan
Imprimé au Japon
<CRD4109-A> UC <KMIZX> <06C00000>
Connecting the Units
WARNING: CAUTION:
• To avoid the risk of accident and the • PIONEER does not recommend that you
potential violation of applicable laws, the install or service your display (sold sepa-
front DVD or TV (sold separately) fea- rately) yourself. Installing or servicing
ture should never be used while the vehi- the product may expose you to risk of
cle is being driven. Also, Rear Displays electric shock or other hazards. Refer all
should not be in a location where it is a installation and servicing of your display
visible distraction to the driver. to authorized Pioneer service personnel.
• In some countries or states the viewing of • Secure all wiring with cable clamps or
images on a display inside a vehicle even electrical tape. Do not allow any bare
by persons other than the driver may be wiring to remain exposed.
illegal. Where such regulations apply,
• Do not drill a hole into the engine com-
they must be obeyed and this unit's DVD
partment to connect the yellow lead of
features should not be used.
the unit to the vehicle battery. Engine
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take extra
care in securing the wire at this point.
• It is extremely dangerous to allow the
display (sold separately) lead to become
wound around the steering column or
gearshift. Be sure to install the display in
such a way that it will not obstruct dri-
ving.
• Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work prop-
erly.
• Do not install the display (sold sepa-
rately) where it may (i) obstruct the
driver's vision, (ii) impair the perfor-
mance of any of the vehicle's operat-
ing systems or safety features, includ-
ing air bags, hazard lamp buttons or
(iii) impair the driver's ability to
safely operate the vehicle.
<ENGLISH>
Note: • This unit cannot be installed in a vehicle that
• This unit is for vehicles with a 12-volt battery and does not have an ACC (accessory) position on
negative grounding. Before installing it in a recre- the ignition switch.
ational vehicle, truck, or bus, check the battery
voltage.
• To avoid shorts in the electrical system, be sure to
disconnect the ≠ battery cable before beginning
installation.
• Refer to the owner's manual for details on
connecting the power amp and other units, then
make connections correctly.
• Secure the wiring with cable clamps or adhesive
ACC position No ACC position
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• The black lead is ground. Please ground this lead
• Route and secure all wiring so it cannot touch any
separately from the ground of high-current prod-
moving parts, such as the gear shift, handbrake and
ucts such as power amps.
seat rails. Do not route wiring in places that get
If you ground the products together and the ground
hot, such as near the heater outlet. If the insulation
becomes detached, there is a risk of damage to the
of the wiring melts or gets torn, there is a danger of
products or fire.
the wiring short-circuiting to the vehicle body.
• Don't pass the yellow lead through a hole into the
engine compartment to connect to the battery. This
• Cords for this product and those for other prod-
will damage the lead insulation and cause a very
ucts may be different colors even if they have
dangerous short.
the same function. When connecting this product
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should. to another product, refer to the supplied manuals
• Never feed power to other equipment by cutting of both products and connect cords that have the
same function.
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing the fuse, be sure to only use a fuse
of the rating prescribed on the fuse holder.
• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same colors
correctly.