Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....9 Ignition Key Removal ....9 Locking Doors With The Key .
Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Horn Chirp Feature .....18 To Unlock The Trunk ....19 Using The Panic Alarm .
Page 9: Things To Know Before Starting Your Vehicle 7
A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 10: Locking Doors With The Key
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever.
Page 11: Replacement Keys
immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a problem with the electronics. If the bulb begins to flash after the bulb check, this indicates that an invalid key has been used to start the vehicle.
Page 12: Customer Key Programming
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to the dealer.
Page 13: Steering Wheel Lock
STEERING WHEEL LOCK Your vehicle is equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key. If the steering wheel is rotated no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
Page 14: Power Door Locks
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death.
Page 15: Automatic Door Locks
4. A single chime will sound to signify that you have successfully disabled the double activation feature. You can turn the feature back on by repeating the above mentioned procedure. You can turn the feature back on by repeating the above mentioned procedure.
Page 16: Child-Protection Door Lock System (Rear Doors)
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child-Protection Door Lock System (Rear Doors) Child Lock Control To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child- protection door lock system. To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
Page 17: Internal Emergency Trunk Lid Release
INTERNAL EMERGENCY TRUNK LID RELEASE WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
Page 18: Remote Keyless Entry - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY — IF EQUIPPED This system allows you to lock or unlock the doors and trunk or activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held transmitter. Four Button Transmitter NOTE: A slight delay of up to two seconds can occur before the doors or trunk will unlock.
Page 19: To Unlock The Trunk
A chime will sound to signify that the feature has been successfully completed. To Unlock the Trunk Press the TRUNK button on the transmitter twice to unlock the trunk. NOTE: A slight delay of up to two seconds can occur before the trunk unlatches.
Page 20: General Information
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, in- cluding interference that may cause undesired operation.
Page 21: Vehicle Theft Alarm
3. To reassemble the transmitter case, snap two halves together. Make sure there is an even gap between the two halves. Test transmitter operation. VEHICLE THEFT ALARM The system monitors the doors, trunk latch, and ignition for unauthorized operation. If something triggers the alarm, the system will signal for about 18 minutes.
Page 22: To Disarm The System
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the trunk is opened with the key while the system is armed, the alarm will sound. To disarm the system: Unlock a front door using either the key or the Keyless Entry Transmitter.
Page 23: Occupant Restraints
OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and side airbags for both the driver and front passenger.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 25 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
Page 27: Adjustable Upper Shoulder Belt Anchorage
WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision.
Page 28: Lap/Shoulder Belt Untwisting Procedure
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. Twisted Seat Belt 1. Position the latch plate as close as possible to the anchor point. Positioning Latch Plate...
Page 29: Seat Belts And Pregnant Women
2. At about 6 to 12 inches above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. Creating A Fold 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
Page 30: Seat Belt Extender
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can...
Page 31 NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. Side Airbags NOTE: Airbag covers may not be obvious in the...
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instru- ment panel knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection.
Page 33 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Right and Left Side Impact Airbag Control Modules (SIACM) • Interconnecting Wiring How The Airbag System Works Front Airbag System • The front Airbag Control Module determines if a frontal collision is severe enough to require the airbags to inflate.
Page 35 WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you have not healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation.
Page 37 • In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered by the appropriate SIACM, releasing a quantity of non- toxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door.
Page 38: Child Restraint
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately: •...
Page 39 • Safety experts recommend that rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and “convertible” child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
Page 41 • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To attach a child restraint tether strap: 1. Lift the cover over the anchor directly behind the seat where you are placing the child restraint. Tether Strap Mounting 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat.
Page 43 provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
Page 44: Transporting Pets
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint.
Page 45: Engine Break-In Recommendations
ENGINE BREAK-IN RECOMMENDATIONS The engine in your new vehicle does not require a long break-in period. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in.
Page 46: Safety Checks You Should Make Inside The Vehicle
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision.
Page 47: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......49 Inside Day/Night Mirror ....49 Outside Mirror —...
Page 48 48 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers ....58 Mist Function ......58 Intermittent Wiper System .
Page 49: Mirrors
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 50: Electric Remote-Control Mirrors
50 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors Use the mirror select switch, located on the drivers door trim panel, to adjust the view obtained in the outside mirrors. Press the rocker knob to the L or R for Left or Right mirror selection.
Page 51: Reclining Bucket Seats
WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Page 52: Folding Rear Seat
52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat To provide additional storage area, the center of each rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. Folding Rear Seat WARNING! •...
Page 53: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the driver’s side of the instrument panel. Hood Release Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 Then lift the safety catch located under the front edge of the hood, near the center and raise the hood.
Page 54: Lights
54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod to secure the hood in the open position as shown. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage.
Page 55: Interior Lights
Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 8 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation.
Page 56: Multi-Function Control Lever
56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever The Multi-Function Control Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and fog lights. The lever is located on the left side of the steering column.
Page 57: Daytime Running Lights (Canada Only)
Daytime Running Lights (Canada Only) The front fog lights will come on as Daytime Running Lights whenever the ignition is on, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door...
Page 58: Windshield Wipers And Washers
58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the control lever. Move the control lever up to select the desired wiper speed. Windshield Wiper/Washer Control Windshield Washers To use the washer, pull the control lever toward you and hold while spray is desired.
Page 59: Intermittent Wiper System
Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Move the lever to the first detent (DEL) position, then select the delay interval by turning the end of the stalk. Rotate the end upward to decrease the delay time and downward to increase it.
Page 60: Power Sunroof - If Equipped
60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 61: Sunroof Maintenance
Once the sunroof panel is in the full vent position, you may momentarily move the switch rearward (less than one second) to initiate the express open mode. During this operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. NOTE: When closing the sunroof, make sure the close button is held in the close position until the motor stops.
Page 62: Wind Buffeting
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if so equipped) in certain open or partially open positions.
Page 63: Ash Receiver And Cigar Lighter
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 Ash Receiver and Cigar Lighter When the Smoker’s Package is ordered from your autho- rized dealer, an ash receiver tray and a cigar lighter element are furnished. The lighter element can be in- serted in the auxiliary power outlet.
Page 65: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....67 Instrument Cluster—Turbo ....68 Instrument Cluster Descriptions .
Page 66 66 UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode In RBP, RBU, RAZ, RB1 And RBQ Radios ..... .81 Selecting a Channel .....82 Storing And Selecting Pre-Set Channels .
Page 67: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 67 INSTRUMENT PANEL FEATURES...
Page 68: Instrument Cluster-Turbo
68 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—TURBO...
Page 69: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fog Light Indicator This light shows when the fog lights are ON. 2. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light comes on, it may indicate that the parking brake is applied, or there is a low brake fluid level.
Page 70 70 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required, however, the conventional brake system will continue to operate normally provided that the BRAKE warning light is not If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefit of Anti-Lock...
Page 71 The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. 9. Seat Belt Reminder Light When the ignition key is first turned on, this light will come on for about six seconds. A chime will sound if you have not pulled the shoulder belt out of the retractor.
Page 72 72 UNDERSTANDING YOUR INSTRUMENT PANEL 16. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors engine con- trol systems. The light will be illuminated when the key is in the ON/RUN position before engine start.
Page 73 20. Trip Indicator This light will illuminate when the Trip Odometer is in use. 21. Temperature Gauge The temperature gauge shows engine coolant temperature. Normal operating range should be within one notch above or one notch below the 200 degree mark. The gauge pointer may show a higher than normal temperature when driv- ing in hot weather, up mountain...
Page 74: Electronic Digital Clock
74 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position.
Page 75: Electrical Disturbances
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
Page 76 76 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode.
Page 77: Cd Player Operation
Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers.
Page 78 78 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
Page 79: Cd Changer Control Capability - If Equipped
Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play. Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped).
Page 80: Satellite Radio - If Equipped
80 UNDERSTANDING YOUR INSTRUMENT PANEL Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s...
Page 81: Electronic Serial Number/Sirius Identification Number (Ens/Sid)
1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Your Vehicle Identification Number. Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Num- ber is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With RBB, RAH and RBK Radios With the ignition switch in the ACCESSORY position and...
Page 82: Selecting A Channel
82 UNDERSTANDING YOUR INSTRUMENT PANEL • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds. • The current program type and channel number will then be displayed for 5 seconds. • The current channel number will then be displayed until an action occurs.
Page 83: Pty Button Seek
NOTE: Pressing the SEEK or SCAN button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button SEEK When the desired program is obtained, press the SEEK button within five seconds.
Page 84: Radio Operation And Cellular Phones
84 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding.
Page 85 NOTE: The air conditioning compressor will not en- gage until the engine has been running for about 10 seconds. Fan speeds to the right of OFF are for heater or ventila- tion operation. The fan speed increases as you move the control clockwise from the OFF position.
Page 86 86 UNDERSTANDING YOUR INSTRUMENT PANEL Air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for main- taining comfort while reducing moisture on the wind- shield.
Page 87 Circulation Control Use this control to choose be- tween outside air intake or recirculation of the air inside the vehicle. Only use the re- circulate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather.
Page 88: Operating Tips
88 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips...
Page 89 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
Page 90: Electric Rear Window Defroster
90 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRIC REAR WINDOW DEFROSTER A push-button at the center of the instrument panel, below the radio, turns the defroster and the heated mirrors (if equipped) ON or OFF. An amber light shows that the defroster is on. Rear Defroster Switch NOTE: The defroster turns off automatically after 10 minutes of operation.
Page 91: Turbo Boost Gauge
TURBO BOOST GAUGE Your vehicle is equipped with a boost gauge that indi- cates the intake manifold pressure relative to barometric pressure. The engine management system in your vehicle intelligently regulates intake manifold pressure based on environmental (ambient) and engine operating condi- tions.
Page 93: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures .....95 Manual Transaxle ..... .95 Normal Starting .
Page 94 94 STARTING AND OPERATING Radial-Ply Tires ..... . 115 Compact Spare Tire ....115 Tire Spinning .
Page 95: Starting Procedures
STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running.
Page 96: Extremely Cold Weather (Below -20°F Or -29°C)
96 STARTING AND OPERATING If the engine fails to start within 15 seconds, turn the key OFF wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
Page 97: After Starting
CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up. TURBOCHARGER COOL DOWN CHART Driving Conditions Normal Driving...
Page 98: Manual Transaxle
98 STARTING AND OPERATING MANUAL TRANSAXLE NOTE: The parking brake should be engaged and the gear selector placed in REVERSE before leaving the vehicle, especially on an incline. NOTE: Clutch must be depressed for engine to start. Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelera- tor pedal.
Page 99: Recommended Shift Speeds
For most city driving you will find it easier to use only the lower gears. For steady highway driving with light accelerations, 5th gear is recommended. Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged.
Page 100: Downshifting
100 STARTING AND OPERATING TABLE 3-MANUAL TRANSAXLE RECOMMENDED SHIFT SPEEDS IN MPH (KM/H) ENGINE MAXIMUM PERFORMANCE SHIFT SPEEDS SIZE 1 to 2 2 to 3 2.4L TURBO (48) (80) If you exceed these speeds, you may notice the engine cut in and out.
Page 101 Before leaving the vehicle, make sure that the parking brake is set. To set the parking brake, pull up firmly on the lever. Also place the gear selector in Reverse (manual transaxle). To release the parking brake, apply the brake pedal and pull up on the parking brake lever.
Page 102: Brake System
102 STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
Page 103: Power Steering
WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 104: Tire Safety Information
104 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 105 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 106 106 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 107: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 108: Tire Loading And Tire Pressure
108 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. Tire Placard Location Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the, 1) number of people that can be carried in the vehicle...
Page 109 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
Page 110 110 STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and...
Page 111 STARTING AND OPERATING 111...
Page 112: Tires-General Information
112 STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 113: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 114 114 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 115: Radial-Ply Tires
WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Page 116: Tire Spinning
116 STARTING AND OPERATING CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h).
Page 117: Tread Wear Indicators
Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Page 118: Alignment And Balance
118 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Page 119: Tire Chains
Tire Chains Due to limited clearance, tire chains are not recom- mended. CAUTION! Damage to the vehicle may result if tire chains are used. Snow Tires Some areas of the country require the use of snow tires during winter. Some standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire sidewall.
Page 120: Tire Rotation Recommendations
120 STARTING AND OPERATING Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions.
Page 121: Selecting Fuel
If you experience these symptoms, try another brand of “regular” gasoline be- fore considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 122: Gasoline/Oxygenate Blends
122 STARTING AND OPERATING The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability for the engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with mate- rials called oxygenates such as 10% ethanol, MTBE and ETBE.
Page 123: Fuel System Cautions
conditions and would result in unnecessary cost. There- fore you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system.
Page 124: Adding Fuel
124 STARTING AND OPERATING • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 125: Vehicle Loading
NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that the cap is properly tightened. If the gas cap is not tightened properly, the Malfunc- tion Indicator light will come on. Be sure the gas cap is tightened every time the vehicle is fueled.
Page 127: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....128 If Your Engine Overheats ....128 Jacking And Tire Changing .
Page 128: Hazard Warning Flasher
128 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Flasher Switch The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash.
Page 129 NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
Page 130: Jacking And Tire Changing
130 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
Page 131 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. WHAT TO DO IN EMERGENCIES 131 CAUTION! Do not attempt to raise the vehicle by jacking on the crossmember below the radiator or on the front suspension crossmember.
Page 132 132 WHAT TO DO IN EMERGENCIES Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire clears the surface. Miminum tire lift provides maximum vehicle stability.
Page 133: Jump-Starting Procedures Due To A Low Battery
7. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts. Alternate nuts until each nut has been tightened twice. Correct wheel nut torque is 100 ft. lbs. (135 N·m.). If you are not sure about the tightness, have them checked with a torgue wrench by your dealer or at a service station.
Page 134 134 WHAT TO DO IN EMERGENCIES 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch.
Page 135 WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water.
Page 136: Driving On Slippery Surfaces
136 WHAT TO DO IN EMERGENCIES WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
Page 137: Freeing A Stuck Vehicle
4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion.
Page 138: Towing A Disabled Vehicle
138 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE With Ignition Key Your vehicle may be towed if the gearshift lever is in NEUTRAL. If the transaxle is not operative, the vehicle must be towed with the front wheels off the ground. CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in...
Page 139: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Turbo Charged Engine Compartment ..141 Onboard Diagnostic System — OBD II ..142 Emissions Inspection And Maintenance Programs ......143 Replacement Parts .
Page 140 140 MAINTAINING YOUR VEHICLE Hoses And Vacuum/Vapor Harnesses ..161 Brake System ......162 Manual Transaxle .
Page 141: 2.4L Turbo Charged Engine Compartment
MAINTAINING YOUR VEHICLE 141 2.4L TURBO CHARGED ENGINE COMPARTMENT...
Page 142: Onboard Diagnostic System - Obd Ii
142 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, and engine control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
Page 143: Emissions Inspection And Maintenance Programs
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready...
Page 144: Replacement Parts
144 MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
Page 145: Maintenance Procedures
WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 146 146 MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
Page 147 • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C) • Trailer towing • Taxi, Police, or delivery service (commercial service) •...
Page 148 148 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) SAE 5W-30 engine oil is recommended for all operating temperatures.
Page 149 Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All of this manufacturers engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably.
Page 150 150 MAINTAINING YOUR VEHICLE CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 151: Ignition Wiring System
Ignition Wiring System The ignition cables should be kept clean and properly connected. Terminals should be fully seated. Cracked, damaged, or faulty cables should be replaced. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits.
Page 152: Maintenance-Free Battery
152 MAINTAINING YOUR VEHICLE Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is perma- nently sealed. You will never have to add water, nor is periodic maintenance required. CAUTION! When servicing the battery, always reinstall the battery thermowrap. The thermowrap provides bat- tery heat protection and will extend overall battery life.
Page 153: Air Conditioner Maintenance
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
Page 154: Power Steering Fluid Check
154 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 155: Body Lubrication
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, trunk and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit;...
Page 156: Windshield Wiper Blade Replacement
156 MAINTAINING YOUR VEHICLE Windshield Wiper Blade Replacement 1. Lift the wiper arm away from the glass. 2. Rotate the blade 45 degrees to gain access to the release tab. 3. Push the release tab shown in the picture and slide the wiper blade assembly down along the arm.
Page 157: Cooling System
If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have a competent mechanic inspect the complete exhaust system and adjacent body areas of broken, damaged, deteriorated, or mispositioned parts.
Page 158 158 MAINTAINING YOUR VEHICLE Check the front of the radiator for an accumulation of bugs, leaves, etc. Clean the radiator by gently spraying water from a garden hose at the back of the core. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts and tightness of the connection at the bottle and radiator.
Page 159 Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOAT ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below 37°C ( 34°F ) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution.
Page 160 160 MAINTAINING YOUR VEHICLE Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and warm to normal operating tempera- ture, the level of the coolant in the bottle should be between the “FULL”...
Page 161: Hoses And Vacuum/Vapor Harnesses
Points To Remember NOTE: When the vehicle is stopped after a few kilome- ters (a few miles) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulation on the radiator and being vapor- ized when the thermostat opens, allowing hot water to enter the radiator.
Page 162: Brake System
162 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure.
Page 163 NOTE: Inspection of brake hoses should be done whenever the brake system is serviced and every engine oil change. WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately.
Page 164: Manual Transaxle
164 MAINTAINING YOUR VEHICLE WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking. You could have an accident. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
Page 165: Appearance Care And Protection From Corrosion
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body car requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in you vehicle.
Page 166 166 MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Many wheel cleaners contain acids that may harm the wheel surface. Special Care •...
Page 167 Only Mopar Wheel Cleaners are recommended. Any of the “DO NOT USE” items listed below can damage wheels and wheel trim. DO NOT USE: • Any abrasive cleaner • Any abrasive cleaning pad (such as steel wool) or abrasive brush •...
Page 168 168 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
Page 169 Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in the vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content of abrasive cleaners.
Page 170: Fuses
170 MAINTAINING YOUR VEHICLE FUSES Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment; next to the battery. A label identifying the components and circuits is located on the underside of the cover. Underhood Fuses (Power Distribution Center) FUSE Amp/Color —...
Page 171: Interior Fuses
15 Amp/ Hazard Flasher Yellow 15 Amp/Lt. Blue 20 Amp/ Electronic Automatic Yellow Transaxle (EATX) 10 Amp/Red Horn Spare 20 Amp/ Fog Lamp (Export Only) Yellow 20 Amp/ ASD/Fuel Pump Yellow 10 Amp/Red A/C Clutch 15 Amp/Lt. Stop Lamps Blue Interior Fuses The fuse access panel is behind the end cover at the left side of the instrument panel.
Page 172 172 MAINTAINING YOUR VEHICLE 10 Amp/Red Airbag Run Only 20 Amp/ HVAC Blower Yellow 10 Amp/Red Backup Switch/EBL/ Temp/Comp 15 Amp/Lt. High Headlamp Blue 10 Amp/Red Airbag Run-Start 15 Amp/Lt. ABS Engine Run Start Blue 10 Amp/Red ARKEM Run Start 10 Amp/Red Ignition Off/Run/ Start 20 Amp/...
Page 173: Vehicle Storage
VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery. You may: • Disengage the mini fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw). •...
Page 174: Bulb Replacement
174 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the three upper fascia screws. 2. Remove two screws from the headlight assembly and remove the assembly from the vehicle.
Page 175: Front Park/Turn Signal Lights
CAUTION! During installation, be sure when tightening the inboard screw, to only tighten until the rubber grommet on the screw starts to compress against the headlamp module housing. MAINTAINING YOUR VEHICLE 175 Front Park/Turn Signal Lights 1. Remove the headlight assembly 2.
Page 176: Tail/Stop, Rear Turn Signals And Back-Up Lights
176 MAINTAINING YOUR VEHICLE Tail/Stop, Rear Turn Signals and Back-up Lights 1. Open the trunk and move the trunk liner away from the rear light mounting area. 2. Twist the bulb socket 1/4 turn to remove it from the housing. 3.
Page 177: Recommended Fluids, Lubricants And Genuine Parts
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Engine Oil Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
Page 179 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..180 Maintenance Schedule ....180 Schedule “B” ......183 Schedule “A”...
Page 180: Emission Control System Maintenance
180 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 181 NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B” of the Maintenance Schedules section of this manual. NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (163 000 km) or 60 months, whichever comes first, and follow schedule “B”...
Page 182 182 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder and transaxle and add as needed. •...
Page 183: Schedule "B
SCHEDULE “B” Follow schedule “B” If you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C ). • Stop and go driving. • Extensive engine idling. •...
Page 184 184 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter. Replace as necessary.* Inspect and replace, if required, the make-up air filter (located inside the air cleaner).
Page 185 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as neces- sary.* Replace the make-up air filter (located inside the air cleaner).
Page 186 186 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter. Replace as necessary.* Change the manual transaxle fluid.
Page 187 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if neces- sary.
Page 188 188 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and re- place as necessary.* Replace the engine air cleaner filter. Replace the spark plugs.
Page 189 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Flush and replace the engine, if not done at 60 months.
Page 190: Schedule "A
190 SCHEDULE “A” SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the make-up air filter (located inside the air cleaner).
Page 191 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Flush and replace the engine coolant at 60 months, if not done at 100,000 miles. 35,000 40,000 45,000 50,000 (56 000) (64 000) (72 000) (80 000) [42] [48]...
Page 192 192 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary.
Page 193 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary.
Page 194 194 SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 195: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......196 Prepare For The Appointment .
Page 196: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 197 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center. Any communication to the Manufacturer’s Customer Center should include the following information: •...
Page 198: Warranty Information
198 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts.
Page 199 IF YOU NEED CONSUMER ASSISTANCE 199 U.S. ONLY...
Page 200: Mopar Parts
200 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra-...
Page 201: Department Of Transportation Uniform Tire Quality Grades
• Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts.
Page 202: Treadwear
202 IF YOU NEED CONSUMER ASSISTANCE Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled con- ditions on a specified government test course. For ex- ample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
Page 203 INDEX...
Page 204 204 INDEX ABS (Anti-Lock Brake) System ... . . 102 Adding Engine Coolant (Antifreeze) ..159 Adding Fuel ......124 Air Cleaner, Engine (Engine Air Cleaner Filter) .
Page 205 Break-In Recommendations, New Vehicle ..45 Bulb Replacement ....173,174 Capacities, Antifreeze (Engine Coolant) Capacities, Fluid ..... . . 176 Caps, Filler Fuel .
Page 206 206 INDEX Cup Holder ......62 Customer Assistance ....196 Daytime Running Lights .
Page 207 Exhaust Pipes ......156 Exhaust System ......156 Extender, Seat Belt .
Page 208 208 INDEX Headlights ......56 Bulb Replacement ..... 174 Cleaning .
Page 209 Brake Warning ......69 Center Mounted Stop ....176 Daytime Running .
Page 210 210 INDEX Manual, Service ......200 Manual Transaxle ....95,98,164 Fluid Level Check .
Page 211 Steering, Checking ....154 Sunroof ......60 Windows .
Page 212 212 INDEX Adjustment ......50 Rear Folding ......52 Reclining .
Page 213 Alignment ......118 Chains ......119 Changing .
Page 214 214 INDEX Washer, Adding Fluid ....156 Washers, Windshield ..... 58 Washing Vehicle .
Page 215 NOTES...
Page 216 NOTES...

This manual is also suitable for:

2005 pl neon srt4

Dodge 2005 Neon SRT4 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Maintenance Schedules

If You Need Consumer Assistance

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge 2005 Neon SRT4

Summary of Contents for Dodge 2005 Neon SRT4

This manual is also suitable for:

Table of Contents