Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Warnings And Cautions
This number also ap- pears on the Automobile Information Disclosure Label Vehicle Identification Number affixed to a window on your vehicle. Save this label as a convenient record of your vehicle identification number and optional equipment.
Page 7: If Equipped
Partial Zero Emission Vehicle (PZEV) for 2.4L — If Equipped NOTE: If the 8th digit of the vehicle identification number (VIN) contains a J then your vehicle is equipped with the Partial Zero Emissions Vehicle (PZEV) package. NOTE: There are specific instructions regarding when to change the ignition cables and spark plugs with the PZEV package.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....11 Ignition Key Removal ....11 Automatic Transaxle Ignition Interlock System .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Panic Alarm ......21 To Use The Panic Alarm ....21 To Program Additional Transmitters .
Page 11: Things To Know Before Starting Your Vehicle 9
A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 12: Automatic Transaxle Ignition Interlock System
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Page 13: Sentry Key - If Equipped
SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for 2 seconds then shut off.
Page 14: Replacement Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
Page 15: General Information
General Information The Sentry Key system complies with FCC rules part 15. Operation is subject to the following two conditions: 1. this device may not cause harmful interference 2. this device must accept any interference that may be received, including interference that may cause undes- ired operation ILLUMINATED ENTRY SYSTEM The interior lights will come on when you open any door,...
Page 16: Power Door Locks
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks There is a door lock switch on each front door trim panel located to the front of the door handle. Press this switch to lock or unlock the four doors. Power Door Lock Switch If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors...
Page 17: Central Locking - If Equipped
Central Locking — If Equipped All vehicle doors are locked with the first turn of the key to the LOCK position. The double activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors at once.
Page 18: Automatic Unlock On Exit - Only Available If Automatic Door Locks Are Enabled
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door lock switch to lock the doors. Power Door Lock Switch 4. A single chime will indicate the completion of the programming. Automatic Unlock on Exit — Only Available if Automatic Door Locks are Enabled This feature will unlock all the doors when the driver’s door is opened and the ignition switch is in the LOCK...
Page 19: Remote Keyless Entry - If Equipped
WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Child Lock Control NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), lower the window and open the door with the outside door handle.
Page 20: To Lock The Doors
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Press and hold the Unlock button on the transmit- ter. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the LOCK button.
Page 21: Panic Alarm
2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the Trunk button. 3. Release both buttons. Panic Alarm The panic mode unlocks the driver’s door, turns on the interior lights, flashes the headlights, and sounds the horn for about 3 minutes or until the alarm is turned off.
Page 22: Transmitter Battery Service
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference that may be received, including interference that may cause undes- ired operation If your Remote Lock Control fails to operate from a normal distance, check for these two conditions: 1.
Page 23: Vehicle Theft Alarm
VEHICLE THEFT ALARM The system monitors the doors, trunk, and ignition for unauthorized operation. If something triggers the alarm, the system will signal for up to 18 minutes. For the first three minutes the horn will sound and the headlights and interior lights will flash. Then the horn will stop and if the source of the trigger is still present, the lights will continue to flash for another 15 minutes.
Page 24: Trunk Lock And Release
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE Trunk Release Button Use the key or the Remote Keyless Entry Transmitter to open the trunk from outside the vehicle. From inside the car the trunk lid can be released by depressing the Trunk Release Button located on the instrument panel to the left of the steering wheel.
Page 25: Trunk Internal Emergency Release
Trunk Internal Emergency Release Emergency Release NOTE: As a security measure, a Trunk Internal Emer- gency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism.
Page 26: Occupant Restraints
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The window controls on the driver’s door operate all windows. The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. To open the window part way, pull the window switch part way and release it when you want the window to stop.
Page 27: Lap/Shoulder Belts
WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 29 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 31: Seat Belt Pretensioners
Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the lever above the webbing upward to release the anchorage, and then move it up or down to the position that serves you best.
Page 32: Enhanced Driver Seat Belt Reminder System (Beltalert)
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt.
Page 33: Seat Belts And Pregnant Women
NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy.
Page 34: Driver And Right Front Passenger Supplemental Restraint System (Srs) - Airbag
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag Front Airbag Components This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems.
Page 35 WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protec- tive covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to properly wear the vehicle seat belt (see section on “Child Restraint”) should be secured in the rear seat in child restraints or belt- positioning booster seats. Older children who do not use child restraints or belt- positioning booster seats should ride properly buckled up in the rear seat.
Page 37 Airbag System Components The front airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters •...
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The airbag control module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously.
Page 39 If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and right front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Side Airbag System The airbag control module determines if a side collision is severe enough to require the airbag to inflate. The control module receives the level of collision severity from the side impact sensors.
Page 41 Airbag Light You will want to have the airbags ready for your protec- tion in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: •...
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Child Restraints • Safety experts recommend rearward-facing in the vehicle until they are at least one year old and weigh at least 9 kg (20 lbs). Two types of child restraints can be used rearward-facing: infant carriers and “convertible”...
Page 43 Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat.
Page 45 share a common lower anchorage. If you are installing LATCH-compatible child restraints in adjacent rear seat- ing positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not LATCH-compatible, you can only install the child restraints using the vehicle’s seat belts.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
Page 47 In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it.
Page 48: Engine Break-In Recommendations
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instruc- tions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
Page 49: Safety Tips
SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. •...
Page 50: Periodic Safety Checks You Should Make Outside The Vehicle
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear or uneven wear...
Page 51: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Console Features ..... . .54 Console Features — Without Heated Seats ..54 Console Features —...
Page 52 52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) ..67 Lights-On Reminder ....67 Fog Lights —...
Page 53 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 Sunshade Operation ....80 Sunroof Fully Closed ....81 Wind Buffeting .
Page 54: Console Features
54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Console Features — Without Heated Seats Console The front console has two cup holders in the front and a storage bin. An optional removable ashtray may be located in the driver’s side cup holder. The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover.
Page 55: Console Features - With Heated Seats
Console Features — With Heated Seats Console The front console has two cup holders. An optional removable ashtray may be located in the driver’s side cup holder. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover.
Page 56: Mirrors
56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror— If Equipped Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Adjusting Rearview Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 57: Electric Remote-Control Mirrors- If Equipped
CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Electric Remote-Control Mirrors— If Equipped Both of the outside mirrors can be adjusted by using the remote controls mounted on the instrument panel to the left of the steering wheel.
Page 58: Outside Mirror - Driver's Side
58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle.
Page 59: Seats
SEATS Manual Front Seat Adjustments Forward/Rearward The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Manual Seat Adjuster After releasing the adjusting bar, apply forward and rearward body pressure to be sure the seat is latched.
Page 60: Power Seats - If Equipped
60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is located on the inboard side of the driver’s seatback. Turn the control lever forward to increase and rearward to de- crease the desired amount of lumbar support.
Page 61: Adjustable Head Restraints
Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint.
Page 62: To Open And Close The Hood
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident.
Page 63: Lights
Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole marked “prop”...
Page 64 64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control With the parking lights or headlights on, rotating the dimmer control for the interior lights on the Multi-Function Control Lever upward will increase the brightness of the instrument panel lights. Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights.
Page 65: Front Map/Reading Lights - If Equipped
Front Map/Reading Lights — If Equipped These lights are mounted between the sun visors. Each light has a push-on push-off switch. NOTE: The lights will remain on until the switch is pressed a second time, so be sure that they have been turned off before leaving the vehicle.
Page 66: Headlights, Parking Lights, Instrument Panel Lights
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Instrument Panel Lights Turn the end of the control lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Multi-Function Lever To change the brightness of the instrument panel lights, turn the center portion of the lever up or down.
Page 67: Daytime Running Lights (Canada Only)
Daytime Running Lights (Canada Only) The headlights come on at a low intensity level whenever the ignition switch is turned on. The lights remain on until the ignition switch is turned OFF or the parking brake is engaged. The headlight switch must be used for normal night time driving.
Page 68: Windshield Wipers And Washers
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the headlights are turned off before the ignition, they will turn off in the normal manner. WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select the desired wiper speed.
Page 69: Mist
Mist Use this feature when weather conditions make occa- sional usage of the wipers necessary. Pull down and release the control lever for a single wiping cycle. Speed Sensitive Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable.
Page 70: Traction Control- If Equipped
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 71: Electronic Speed Control- If Equipped
ELECTRONIC SPEED CONTROL— IF EQUIPPED When engaged, this device will control the throttle op- eration to maintain a constant vehicle speed between 30 mph (48 km/h) and 85 mph (137 km/h). The controls are on the steering wheel. Speed Control Switches To Activate: Press the ON/OFF switch to turn the speed control system ON.
Page 72: To Deactivate
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake or clutch pressure will deactivate speed control without erasing the memory. Pushing the ON/OFF button or turning off the ignition turns the speed control system off and erases the memory.
Page 73 When Climbing A Hill If vehicle speed drops 3 mph (5 km/h) below the Speed Control set speed, the transaxle will downshift to third gear. Under severe conditions the transaxle may down- shift again to second gear. The transaxle will upshift to fourth gear after the vehicle has reached the top of the hill.
Page 74: Garage Door Opener - If Equipped
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
Page 75 WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
Page 76: Rolling Code" Programming
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure.
Page 77: Canadian Programming/Gate Programming
difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. 2. Press and hold the training button on the garage door opener head unit. This will activate the “training” light. NOTE: After completing step 2, you have 30 seconds to start step 3.
Page 78: Reprogramming A Single Button
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single Button 1. Press and hold the Universal Transceiver button to be reprogrammed. Do not release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds) position the hand held transmitter one to three inches away from the button to be trained.
Page 79: Power Sunroof - If Equipped
POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the sun visors on the overhead console. Power Sunroof Controls UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch.
Page 80: Opening Sunroof - Manual
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Manual Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this opera- tion, any release of the sunroof switch will stop the sunroof.
Page 81 Sunroof Fully Closed Press and hold the switch forward until the sunroof stops completely to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLET The power outlet is located in the lower center of your instrument panel. If your vehicle is equipped with heated seats, a second power outlet is located inside the center console.
Page 83: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....87 Instrument Cluster ..... .88 Instrument Cluster Description .
Page 84 84 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Data System (RDS) ....100 PTY (Program Type) Button ....101 Balance .
Page 85 Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability ......108 Radio Operation .
Page 86 86 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player — Single Disc In Radio ..123 CD Player — 6 Disc CD Changer ..123 Cassette Tape And Player Maintenance .
Page 87: Instruments And Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 87 INSTRUMENTS AND CONTROLS...
Page 88: Instrument Cluster
88 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 89: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Traction Control — If Equipped This display indicator illuminates momentarily as a bulb check when the ignition switch is first turned ON.
Page 90 90 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Tachometer The red area of the scale shows the maximum permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area (over 6,500 rpm), ease up on the accelerator to prevent engine over speed. 6.
Page 91 through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing. The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs.
Page 92 92 UNDERSTANDING YOUR INSTRUMENT PANEL An optional AutoStick Gear Indicator displays the current transaxle gear when in AutoStick mode. 16. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
Page 93 the conventional brake system will continue to operate normally provided that the BRAKE warning light is not 18. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on briefly when the igni- tion is turned on as a bulb check. If the bulb does not come on during starting, have the bulb repaired promptly.
Page 94 94 UNDERSTANDING YOUR INSTRUMENT PANEL The light will also come on when the parking brake is applied with the ignition in the RUN position. NOTE: This light shows only that the parking brake is on. It does not show the degree of brake application. In an ABS equipped vehicle, the Brake System Warning light will come on if the ABS light is not functioning or if the ABS system is not communicating.
Page 95: Compass, Temperature, And Trip Computer Display - If Equipped
COMPASS, TEMPERATURE, AND TRIP COMPUTER DISPLAY — IF EQUIPPED Trip Computer Display This feature allows you to choose between a compass / temperature display and one of five trip conditions being monitored. Control Buttons Step Button Use this button to choose or cycle through the five trip conditions.
Page 96: Trip Conditions
96 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Conditions Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. Estimated Range (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank. This esti- mated distance is based on the most recent trip informa- tion: (Average Fuel Economy) x (Fuel Remaining) This display cannot be reset.
Page 97 Automatic Compass Calibration The self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the CAL symbol will appear on the display. After the vehicle has completed at least one complete circle in an area free from large metal objects, calibration will be complete when the CAL symbol is extinguished.
Page 98: Cigar Lighter/Ashtray
98 UNDERSTANDING YOUR INSTRUMENT PANEL Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F. When the outside temperature is less than 40°F ( 40°C), the display will show 40°F/C. CIGAR LIGHTER/ASHTRAY For a nominal charge your dealer can provide a “smok- er’s”...
Page 99: To Set The Clock
To Set The Clock: 1. Use a ballpoint pen or similar object to press the hour (H) or minute (M) buttons on the radio, The time setting will increase each time you press the button. 2. Press any other button to exit from the clock setting mode.
Page 100: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls
100 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS RAZ Radio Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 101: Pty (Program Type) Button
which are broadcasting this information. PTY (Program Type) is used to characterize the station’s program ma- terial, for example Rock Music . PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off.
Page 102: Balance
102 UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 103: To Set The Radio Push-Button Memory
Pressing the AM/FM button continues the search in the alternate frequency band. To stop the search, press SCAN a second time. To Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window.
Page 104: Fast Forward (Ff)
104 UNDERSTANDING YOUR INSTRUMENT PANEL Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed again or the end of the tape is reached.
Page 105: Operating Instructions - Cd Player
light in the display will go off when the Dolby System is off. The Dolby System is automatically reactivated each time a tape is inserted. * ”Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Labo- ratories Licensing Corporation.
Page 106: Seek Button
106 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 107: Tape Cd Button
current channel name and number will then be displayed until an action occurs. A CD or tape may remain in the player while in the Satellite Radio mode. Tape CD Button Press this button to select between CD player and Tape player.
Page 108: Sales Code Rbb-Am/Fm Stereo Radio With Cassette Tape Player And Cd Changer Capability
108 UNDERSTANDING YOUR INSTRUMENT PANEL CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display.
Page 109 NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 110: Mode Button
110 UNDERSTANDING YOUR INSTRUMENT PANEL stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and FADE.
Page 111: Cassette Player Features
Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on.
Page 112: Cd Changer Control Capability - If Equipped
112 UNDERSTANDING YOUR INSTRUMENT PANEL When Dolby is ON, the NR symbol appears on the display. Each time a tape is inserted the Dolby will turn * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Labo- ratories Licensing Corporation.
Page 113: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically.
Page 114 114 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode.
Page 115: Cd Player Operation
Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers.
Page 116 116 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
Page 117: Cd Changer Control Capability
Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play. Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped).
Page 118 118 UNDERSTANDING YOUR INSTRUMENT PANEL Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s...
Page 119: Disc Cd Changer - If Equipped
6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer.
Page 120: Playing Discs
120 UNDERSTANDING YOUR INSTRUMENT PANEL Playing Discs The radio will show the CD number, the CD track number, and the Track Time Elapsed while the radio is in the CD mode. If more than one CD is loaded in the changer, the changer will automatically play the next disc after playing the last track of the current disc.
Page 121: Time Button
Time Button Press this button to switch between time of day and CD track time. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode. If a CD is loaded, press the Mode button to select the CD mode.
Page 122: Remote Sound System Controls - If Equipped
122 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Remote Sound System Controls The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the sound system.
Page 123: Cd Player - Single Disc In Radio
If you press the switch up or down twice it plays the second selection, three times, it will play the third, etc. The button in the center of the left hand switch has no function in this mode. CD Player — Single Disc in Radio Pressing the top of the switch once will go to the next track on the CD.
Page 124: Compact Disc Maintenance
124 UNDERSTANDING YOUR INSTRUMENT PANEL deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport. The other adverse condition is low or “muddy” sound from one or both channels, as if the treble tone control were turned all the way down.
Page 125: Radio Operation And Cellular Phones
considering disc player service. You may have a problem with CD-R (recordable) and CD-RW (recordable and writable) disks. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio.
Page 126 126 UNDERSTANDING YOUR INSTRUMENT PANEL Interior ATC Sensors There are two interior sensors in the vehicle. The Sun Sensor is mounted in the center of the instrument panel near the windshield glass. The In-Car Temperature Sen- sor is mounted behind the ATC control panel. These sensors transmit data on sun strength and vehicle interior temperatures to enhance system performance.
Page 127 lower it. The comfort setting range is from Low, 60, 61,...to 89,90, Hi, for automatic temperature control. You can select a very hot or cold comfort setting by holding the comfort control until it reaches its highest or lowest levels. The system adjusts to bring the interior temperature to the desired comfort level.
Page 128 128 UNDERSTANDING YOUR INSTRUMENT PANEL Air Direction Buttons (Mode) These buttons allow you to select from five air distribu- tion patterns. These buttons should be used only when you can not achieve comfort or visibility in Auto opera- tion. A symbol in the display window will show which mode is operating.
Page 129 NOTE: The air conditioning compressor is on in this mode. This dehumidifies the air to help dry the wind- shield. To improve fuel economy, leave in the defrost mode only when necessary. Rear Window Defroster Press the button once to turn on the Rear Window Defroster and a second time to turn it off.
Page 130 130 UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters Side window demisters are located on the instrument panel. These non adjustable outlets direct air toward the side windows in any mode except Panel or Panel Recir- culation. The air is directed toward the area of the side windows through which you view the outside rearview mirrors.
Page 131 UNDERSTANDING YOUR INSTRUMENT PANEL 131 Operating Tips (ATC only)
Page 132: Manual Air Conditioning/Heater Control - If
132 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the system is in the AUTO mode and the fan control is already rotated fully clockwise or fully coun- terclockwise, the control may have to be rotated to the middle and then to the desired fan setting for manual adjustment of fan speed.
Page 133 Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. NOTE: If your air conditioning performance seems lower than expected, check the front of the air condition- ing condenser for an accumulation of dirt or insects.
Page 134 134 UNDERSTANDING YOUR INSTRUMENT PANEL • Panel — Air Conditioning Outside air flows through the air condition- ing system and then through the outlets located in the instrument panel. • Bi-Level — Air Conditioning Outside air flows through the air condition- ing system and then through the outlets located in both the instrument panel and floor outlets.
Page 135 Rear Seat Outlets These outlets are located under the front seats and direct warm air to the rear seat passengers. Air is directed through these outlets when you select either the Floor, Bi-Level, or Mix modes. Rear Window Defroster The Rear Window Defroster button is located to the right of the Mode Control.
Page 136 136 UNDERSTANDING YOUR INSTRUMENT PANEL Summer Operation Air conditioned vehicles must be protected with a high- quality antifreeze coolant to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50 % concentration is recommended.
Page 137 UNDERSTANDING YOUR INSTRUMENT PANEL 137 Operating Tips (Manual A/C Control Only)
Page 138 138 UNDERSTANDING YOUR INSTRUMENT PANEL Outside Air Intake Make sure the air intake, directly in front of the wind- shield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains. Air Intake...
Page 139: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....142 Automatic Transaxle ....142 Manual Transaxle .
Page 140 140 STARTING AND OPERATING Tire Markings ......154 Tire Identification Number (TIN) ..158 Tire Loading And Tire Pressure .
Page 141 Flexible Fuel – (2.7L Engines With Automatic Transmission Only) ..... 180 E-85 General Information ....180 Ethanol Fuel (E-85) .
Page 142: Starting Procedures
142 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
Page 143 Ignition Key Positions WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. STARTING AND OPERATING 143 CAUTION! Do not attempt to push or tow your vehicle to get it started.
Page 144: Extreme Cold Weather (Below -20°F Or -29°C)
144 STARTING AND OPERATING Extreme Cold Weather (below -20°F or -29°C) To insure reliable starting at these temperatures, use of an externally powered electric engine block heater and battery blanket heater package (available from your dealer) is recommended. If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING”...
Page 145: After Starting
After Starting The idle speed will automatically decrease as the engine warms up. At cooler ambient temperatures, the idle speed for the 2.7L engine may increase during extended idles for improved heater performance. BATTERY AND ENGINE BLOCK HEATERS — If EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather.
Page 146 146 STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is run- ning. Before exiting a vehicle you should shift the transmission into Park, remove the key from the ignition, and apply the park brake.
Page 147: Automatic Transaxle Ignition Interlock System
WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 148: Gear Ranges For Four Speed Automatic
148 STARTING AND OPERATING NOTE: Even if the transaxle can be reset, it is recom- mended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transaxle cannot be reset, dealer service is required. Gear Ranges For Four Speed Automatic Transaxle DO NOT race the engine when shifting from PARK or...
Page 149 “D” Overdrive This range should be used for most city and highway driving. It provides smoothest up shifts and down shifts and best fuel economy. When frequent transaxle shifting occurs while using the Overdrive range, such as when operating the vehicle under heavy loading conditions (in hilly terrain, travel- ing into strong head winds, or while towing heavy trailers), use the “3”...
Page 150: Parking Brake
150 STARTING AND OPERATING PARKING BRAKE When the parking brake is applied with the ignition on, the brake light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. Parking Brake Before leaving the vehicle, make sure that the parking brake is set.
Page 151: Brake System
WARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
Page 152: Anti-Lock Brake System (Abs) - If Equipped
152 STARTING AND OPERATING Anti-Lock Brake System (ABS) — If Equipped The ABS gives increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. All vehicle wheels and tires must be the same size and tires must be properly inflated to produce accurate signals for the ABS computer.
Page 153: Power Steering
POWER STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort.
Page 154: Tire Safety Information
154 STARTING AND OPERATING • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control light located in the instrument cluster.
Page 155 NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width.
Page 156 156 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm)
Page 157 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 158: Tire Identification Number (Tin)
158 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 159: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B”...
Page 160 160 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
Page 161 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and STARTING AND OPERATING 161...
Page 162 162 STARTING AND OPERATING...
Page 163: Tires-General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 164: Tire Inflation Pressures
164 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
Page 165 CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 166: Radial-Ply Tires
166 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Page 167: Limited Use Spare - If Equipped
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the...
Page 168: Tread Wear Indicators
168 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
Page 169: Replacement Tires
Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators).
Page 170: Alignment And Balance
170 STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear.
Page 171: Tire Rotation Recommendations
Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions.
Page 172: Autostick - If Equipped
172 STARTING AND OPERATING AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transaxle that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
Page 173: Autostick General Information
Autostick General Information • The transaxle will automatically upshift from first to second gear and from second to third gear when engine speed reaches about 6300 RPM. • Downshifts from third to second gear above 66 mph (106 km/h) and from second to first gear above 37 mph (60 km/h) will be ignored.
Page 174: Reformulated Gasoline
If you experience these symptoms, try another brand of “regular” gasoline be- fore considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 175: Mmt In Gasoline
MMT in Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles.
Page 176: Carbon Monoxide Warnings
176 STARTING AND OPERATING Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives are not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
Page 177 CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! To avoid fuel spillage and overfilling, do not “top off”...
Page 178: Vehicle Loading
178 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle.
Page 179: Towing Requirements
• The weight of any other type of cargo or equipment put in or on your vehicle. • Remember that everything put in or on the trailer adds to the load on your vehicle. Towing Requirements • The maximum trailer load is 1,000 lbs (450 kg). •...
Page 180 180 STARTING AND OPERATING NOTE: Check the automatic transaxle fluid level before towing. Fluid discoloration, or a burnt odor, shows the need for a transmission fluid and filter change. NOTE: For vehicles equipped with Autostick. By using the Autostick modes, and selecting a specific gear range, frequent shifting can be avoided.
Page 181 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
Page 182 182 STARTING AND OPERATING This symbol means that the oil has been certified by the American Petroleum Institute (API). We only recommend API Certified en- gine oils that meet the require- ments of DaimlerChrysler’s Mate- rial Standard MS-9214. Use Mopar or an equivalent oil meeting the specification MS-9214.
Page 183 Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F (-18°C). In the range of 0°F to 32°F (-18°C to 0°C), you may experience an increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesita- tions) until the engine is fully warmed up.
Page 185: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....186 If Your Engine Overheats ....186 Jacking And Tire Changing .
Page 186: Hazard Warning Flasher
186 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Flasher Switch The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash.
Page 187 the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle.
Page 188: Jacking And Tire Changing
188 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
Page 189 WHAT TO DO IN EMERGENCIES 189 1. Block wheel diagonally op- posite flat tire. 2. Remove the spare tire, scissors jack and lug wrench from stowage.
Page 190 190 WHAT TO DO IN EMERGENCIES 3. Before raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels). Loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground.
Page 191 WHAT TO DO IN EMERGENCIES 191 Jack Engagement Locations...
Page 192 192 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove lug nuts and tire. 7.
Page 193: Jump-Starting Procedures If Battery Is Low
JUMP-STARTING PROCEDURES IF BATTERY IS WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 194 194 WHAT TO DO IN EMERGENCIES WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and person injury could result. Jump Starting 5. Connect the other cable, first to the negative terminal of the booster battery and then to the jump start attach- ment of the vehicle with the discharged battery.
Page 195 WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. WHAT TO DO IN EMERGENCIES 195 WARNING! Battery fluid is a corrosive acid solution;...
Page 196: Driving On Slippery Surfaces
196 WHAT TO DO IN EMERGENCIES DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels, particularly with high output engines.
Page 197: Freeing A Stuck Vehicle
FREEING A STUCK VEHICLE If your vehicle is equipped with Traction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.
Page 198: Towing This Vehicle Behind Another Vehicle
198 WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Automatic Transaxle Your vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be towed must not exceed 15 miles (25 km), and the towing speed must not exceed 25 mph (40 km/h).
Page 199: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Engine ......201 2.7L Engine ......202 Onboard Diagnostic System —...
Page 200 200 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion ......230 Fuses ....... 235 Underhood Fuses (Power Distribution Center) .
Page 201: 2.4L Engine
MAINTAINING YOUR VEHICLE 201 2.4L ENGINE 2.4L Engine Compartment...
Page 202: L Engine
202 MAINTAINING YOUR VEHICLE 2.7L ENGINE 2.7L Engine Compartment...
Page 203: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 204: Emissions Inspection And Maintenance
204 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running,...
Page 205: Replacement Parts
If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
Page 206: Maintenance Procedures
206 MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 207 Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you.
Page 208 208 MAINTAINING YOUR VEHICLE If none of these apply to you, then change your engine oil at every interval shown on schedule A of the Mainte- nance Schedules section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months whichever comes first.
Page 209 Engine Oil Viscosity (SAE Grade) Engine Oil Fill Cap SAE 5W-20 and SAE 5W-30 engine oils are recom- mended for all operating temperatures. These engine oils are designed to improve low temperature starting and vehicle fuel economy. Refer to the engine oil filler cap for the preferred engine oil viscosity grade for each vehicle.
Page 210 210 MAINTAINING YOUR VEHICLE Materials Added To Engine Oils The manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives.
Page 211 replaced if there is any malfunction due to a faulty spark plug. Check the specifications section for the proper type of spark plug for use in your vehicle. Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”.
Page 212 212 MAINTAINING YOUR VEHICLE CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 213: Crankcase Emission Control System
Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the Positive Crankshaft Ventilation (PCV) valve and passages may accumulate deposits. If a valve is not working properly, replace it with a new valve.
Page 214: Air Conditioner
214 MAINTAINING YOUR VEHICLE WARNING! Battery posts, terminals and related accessories con- tain lead and lead compounds. Wash hands after handling. Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps.
Page 215: Power Steering - Fluid Check
through the condenser as required. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you.
Page 216: Suspension Ball Joints
216 MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturer recommended power steering fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
Page 217 underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. Hood Latch When performing other under hood services, the hood latch release mechanism and safety catch should be inspected, cleaned, and lubricated. It is important to maintain proper lubrication to insure that the hood mechanisms work properly and safely.
Page 218: Windshield Wiper Blades
218 MAINTAINING YOUR VEHICLE Smooth White Body Lubricant - Such as Mopar Spray White Lube: • Hood hinge springs and links • Lock cylinders • Parking brake mechanism • Trunk latches • Ash tray Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner.
Page 219: Exhaust System
Washer Fluid Reservoir WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. MAINTAINING YOUR VEHICLE 219 Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
Page 220: Cooling System
220 MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, fol- low the preceding safety tips. Cooling System Inspection WARNING!
Page 221 Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the radiator for any accumulation of bugs, leaves, etc.
Page 222 222 MAINTAINING YOUR VEHICLE If the solution is dirty and contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Used automotive antifreeze is a recyclable commodity. Discard or recycle as facilities exist in your area.
Page 223 Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOAT ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below 34°F ( 37°C) are anticipated. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where...
Page 224 224 MAINTAINING YOUR VEHICLE Disposal Of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. Do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground.
Page 225: Hoses And Vacuum/Vapor Harnesses
• Check coolant freeze point in the system. • If frequent coolant additions are required, or if the level in the bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain coolant concentration at 50% HOAT ethylene glycol engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components.
Page 226 226 MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You may not have your full braking capacity in an emergency.
Page 227 Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp shows system failure. Brake Fluid Reservoir Be sure to clean the top of the master cylinder area before removing the cap.
Page 228: Fuel System Hoses
228 MAINTAINING YOUR VEHICLE Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result! Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and clamps which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline.
Page 229 Procedure For Checking Fluid Level The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. To properly check the automatic transaxle fluid level, the following procedure must be used: •...
Page 230: Appearance Care And Protection From Corrosion
230 MAINTAINING YOUR VEHICLE • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for mainte- nance schedules. If the transaxle is disassembled for any reason, the fluid and filter should be changed.
Page 231 What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. •...
Page 232 232 MAINTAINING YOUR VEHICLE • Use Mopar touch up paint on scratches or chips as soon as possible. Your dealer has touch up paint to match the color of your vehicle. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible.
Page 233 You should not increase the gloss level, especially on top of the instrument panel top surface. Higher gloss levels will increase the reflectivity in the windshield that could decrease visibility under bright light driving conditions. WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
Page 234 234 MAINTAINING YOUR VEHICLE Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instru- ments which may scratch the elements. Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections in the windshield.
Page 235: Fuses
FUSES Underhood Fuses (Power Distribution Center) Power Distribution Center MAINTAINING YOUR VEHICLE 235 A Power Distribution Center is located in the engine compartment; near the air cleaner. This information ap- plies to vehicles built without the fuse and relay num- bering embossed on the Power Distribution Center Top Cover.
Page 236 236 MAINTAINING YOUR VEHICLE The identity of each fuse is indicated on the backside of the cover. Cavity Fuse Circuit 30 Amp Green Blower Motor 10 Amp Red Right High Beam Head- light, High Beam Indica- 10 Amp Red Left High Beam Head- light 15 Amp Blue Power Door Lock Switch...
Page 237: Vehicle Storage
Cavity Fuse Circuit 10 Amp Red Instrument Cluster, Transmission Control, Park/Neutral Switch, Body Control Module 10 Amp Red Left Low beam Headlight 20 Amp Yellow Right Low Beam Head- light, Fog Light Switch 10 Amp Red Radio 10 Amp Red Turn Signal and Hazard Flashers, Wiper Switch, Seat Belt Control Module,...
Page 238: Replacement Light Bulbs
238 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior ABS Lamp ......PC 161 Instrument Cluster .
Page 239 2. Remove the push-in fasteners by prying under the head of the fasteners with a flat bladed tool. MAINTAINING YOUR VEHICLE 239 3. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender.
Page 240: Park, Turn Signal, Sidemarker Bulb Replacement
240 MAINTAINING YOUR VEHICLE 4. Turn the retaining ring counterclockwise and remove the bulb and socket assembly. 5. Pull the bulb out of the socket and replace the bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
Page 241: Fog Light Bulb Replacement
2. Turn the bulb socket counterclockwise and remove the bulb and socket assembly. 3. Pull the bulb out of the socket, replace the bulb, and reinstall the bulb and socket to the headlight assembly. Reinstall the headlight assembly. MAINTAINING YOUR VEHICLE 241 Fog Light Bulb Replacement 1.
Page 242: Center Stoplight Bulb Replacement
242 MAINTAINING YOUR VEHICLE 4. Turn the bulb and socket assembly counterclockwise to remove it from the housing. 5. Install the new bulb and socket assembly, reattach the wiring connector, and reinstall the fog light assembly. Center Stoplight Bulb Replacement 1.
Page 243: Rear Light Bulb Replacement
Rear Light Bulb Replacement 1. Open the trunk and pull the trunk liner away to expose the wiring connector and light housing plastic retainers. 2. Disconnect the wiring connector and remove the plas- tic retainers. Remove the light housing from the vehicle. MAINTAINING YOUR VEHICLE 243 3.
Page 244: Headlight Aiming
244 MAINTAINING YOUR VEHICLE Headlight Aiming The headlights on your new vehicle were aimed at the factory. The factory setting was made at a no load setting. A great increase in weight will change the aiming and it may be necessary to readjust the headlights if carrying an excessive amount of weight in the trunk, rear seats or pulling a trailer.
Page 245: Recommended Fluids, Lubricants And Genuine
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Engine Oil Use API Certified engine oil. SAE 5W-20 and SAE 5W-30 are recommended. Refer to the engine oil fill cap for the correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
Page 246: Chassis
246 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Steering Gear & Linkage, Ball Joints, Prop Shafts & Yokes, Wheel Bearings Fluid, Lubricant, or Genuine Part Mopar ATF+4 Automatic Transmission Fluid. Mopar Brake Fluid DOT 3 Motor Vehicle. Mopar ATF+4 Automatic Transmission Fluid.
Page 247 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..248 Partial Zero Emissions Vehicle (PZEV) For 2.4L — If Equipped ......248 Maintenance Schedules .
Page 248: Emission Control System Maintenance
248 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 249: Maintenance Schedules
NOTE: There are specific instructions regarding when to change the ignition cables and spark plugs with the PZEV package in this section. This applies to both maintenance schedule A and B and will be marked with an ** or ***. MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle.
Page 250 250 MAINTENANCE SCHEDULES Use the schedule that best describes your driving condi- tions. Where time and mileage are listed, follow the interval that occurs first. NOTE: Under no circumstances should oil change intervals exceed 6 months or 6,000 miles, whichever comes first.
Page 251 At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect the brake linings, hoses and calipers. • Inspect the CV joints and front and rear suspension components. • Check the automatic transmission fluid level. MAINTENANCE SCHEDULES 251 •...
Page 252: 252 Schedule "B
252 SCHEDULE “B” SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
Page 253 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires. 3,000 6,000 9,000...
Page 254 254 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine).
Page 255 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires. 39,000 42,000 45,000...
Page 256 256 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Inspect the air cleaner filter and replace if neces- sary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine).
Page 257 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
Page 258 258 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the spark plugs on the 2.4 liter en- gine. *** Replace the ignition cables on the 2.4 liter en- gine.
Page 259 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on the 2.4 liter en- gine. ** Replace the ignition cables on the 2.4 liter en- gine.
Page 260 260 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
Page 261 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on the 2.4 liter engine. ** Inspect the front and rear brake pads, linings, rotors, rear drums and shoes.
Page 262: Partial Zero Emissions Vehicle (Pzev) For 2.4L - Schedule "A
262 SCHEDULE “A” SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on 2.4 liter engine. ** Inspect the front and rear brake pads, linings, rotors, rear drums and shoes.
Page 263 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
Page 264 264 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter en- gine.
Page 265 Miles (Kilometers) [Months] Replace the spark plugs on 2.4 liter en- gine. *** Flush and replace the engine coolant, if not replaced at 60 months. Rotate the tires. 78,000 84,000 90,000 96,000 (125 000) (134 000) (144 000) (154 000) (160 000) (163 000) (168 000) [78] [84] [90]...
Page 266 266 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine.
Page 267 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Check and replace, if necessary, the PCV valve. *‡ Replace the engine timing belt on 2.4 liter engine.*** Replace the spark plugs on 2.4 liter engine.
Page 268 268 SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 269: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......270 Prepare For The Appointment .
Page 270: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 271 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center. Any communication to the Manufacturer’s Customer Center should include the following information: •...
Page 272: Warranty Information
272 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts.
Page 273 IF YOU NEED CONSUMER ASSISTANCE 273 U.S. ONLY...
Page 274: Mopar Parts
274 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra-...
Page 275 • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts.
Page 276: Department Of Transportation Uniform Tire Quality Grades
276 IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
Page 277: Temperature Grades
Temperature Grades The temperature grades are A (highest), B, and C, repre- senting the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 279 INDEX...
Page 280 280 INDEX About Your Brakes ..... . 151 ABS (Anti-Lock Brake) System ... . . 152 Adding Engine Coolant (Antifreeze) .
Page 281 Special Additives ..... 230 Autostick ......172 Auxiliary Power Outlet .
Page 282 282 INDEX Charging System Light ....90 Chart, Tire Sizing ..... . . 156 Check Engine Light (Malfunction Indicator Light) .
Page 283 Daytime Running Lights ....67 Dealer Service ......205 Defroster, Rear Window .
Page 284 284 INDEX Overheating ......186 Partial Zero Emissions Vehicle for 2.4 Liter . . 248 Timing Belt ......212 Engine Oil Viscosity .
Page 285 Filler Cap ......176 Filter ......211 Gasoline .
Page 286 286 INDEX Ignition Key ....... . 11 Lock ....... . 11 Illuminated Entry .
Page 287 Engine Temperature Warning ... . . 91 Exterior Check ......50 Fog .
Page 288 288 INDEX Schedule A ......262 Schedule B ......252 Malfunction Indicator Light .
Page 289 Partial Zero Emissions Vehicle for 2.4 Liter ..248 Passing Light ......67 Pets .
Page 290 290 INDEX Safety Checks Inside Vehicle ....49 Safety Checks Outside Vehicle ....50 Safety Defects, Reporting .
Page 291 Cold Weather ......144 Engine Fails to Start ....144 Starting and Operating .
Page 292 292 INDEX Tread Wear Indicators ....168 Towing ......178,197,198 Disabled Vehicle .
Page 293 Warning, Door Ajar ..... . 17 Warning Flasher, Hazard ....186 Warnings and Cautions .

This manual is also suitable for:

2005 stratus

Dodge 2005 JR41 Stratus Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge 2005 JR41 Stratus

Summary of Contents for Dodge 2005 JR41 Stratus