Table of Contents
Advertisement
Quick Links
Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E
Input/Output Controllers
This feature module describes the two new variants of the Cisco 7200 I/O card. The
Cisco 7200-I/O-GE+E provides one Gigabit Ethernet port and one Ethernet port. The
Cisco 7200-I/O-2FE/E provides two autosensing Fast Ethernet 10/100 Mb ports.
This document includes the following sections:
•
•
•
•
•
•
•
Feature Overview
The Cisco 7200-I/O-GE+E is an Input/Output controller that provides one Gigabit Ethernet and one
Ethernet port. It is equipped with a GBIC receptacle for 1000 megabits per second (Mbps) operation
and an RJ-45 receptacle for 10 Mbps operation.
The Cisco 7200-I/O-2FE/E is an Input/Output controller that provides two autosensing Fast Ethernet
ports and is equipped with two RJ-45 receptacles for 10/100 Mbps operation.
I/O controllers support the following features:
•
•
•
•
•
Feature Overview
Supported Platforms
Supported Standards, MIBs, and RFCs
Configuration Tasks
Monitoring and Maintaining the Cisco 7200-I/O GE+E and Cisco 7200-2FE/E
Configuration Examples
Command Reference
Dual EIA/TIA-232 channels for local console and auxiliary ports
NVRAM for storing the system configuration and environmental monitoring logs
Two PC Card slots that hold Flash disks or Flash memory cards for storing the default Cisco IOS
software image
Flash memory for storing the boot helper image
Two environmental sensors for monitoring the cooling air as it enters and leaves the chassis
12.1(5)T and 12.2(14) S
1
Advertisement
Table of Contents
Related Manuals for Cisco C7200-I - Input/Output Controller - Control Processor
Summary of Contents for Cisco C7200-I - Input/Output Controller - Control Processor
-
Page 1: Feature Overview
Dual EIA/TIA-232 channels for local console and auxiliary ports • NVRAM for storing the system configuration and environmental monitoring logs • Two PC Card slots that hold Flash disks or Flash memory cards for storing the default Cisco IOS • software image •... -
Page 2: Related Documents
Gigabit Ethernet connectivity or dual Fast Ethernet connectivity for WAN aggregation type services, without having to sacrifice a port adapter slot. Restrictions The Cisco 7200 2 FE/E does not operate with the following Network Processor Engines: NPE-100, • NPE-150, NPE-175, or NPE-200. -
Page 3: Supported Standards, Mibs, And Rfcs
Changes the Fast Ethernet interface port Router(config-if)# duplex full transmission mode to full duplex from autonegotiation. Use the interface fastethernet router-shelf/slot/port command for a Cisco 7200 VXR used as a router shelf in an AS5800 Universal Access Server. 12.1(5)T and 12.2(14) S... -
Page 4: Configuring Interface Speed
Router# speed 10 10 Mbps. Use the interface ethernet router-shelf/slot/port command for a Cisco 7200 VXR used as a router shelf in an AS5800 Universal Access Server. Use the interface fastethernet router-shelf/slot/port command for a Cisco 7200 VXR used as a router shelf in an AS5800 Universal Access Server. -
Page 5: Verifying The Configuration
Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers Configuration Tasks Use the interface fastethernet router-shelf/slot/port command for a Cisco 7200 VXR used as a router shelf in an AS5800 Universal Access Server. Verifying the Configuration Use the show interfaces {ethernet | fastethernet | gigabitethernet} command to verify that the interface and line protocol are in the correct state (up) and the transmission mode is configured on the interface. -
Page 6: Configuration Examples
Router# show interfaces fastethernet interface on the router. 1. Use the show interfaces ethernet router-shelf/slot/port command for a Cisco 7200 VXR used as a router shelf in an AS5800 Universal Access Server. Configuration Examples This section provides the following configuration examples: •... -
Page 7: Command Reference
Router(config-if)# ip address 1.1.1.10 255.255.255.252 Router(config-if)# negotiation auto Router(config-if)# end Configuring Autonegotiation on the Cisco 7200-I/O-2FE/E The following example configures the Fast Ethernet interface on the Cisco 7200-I/O-2FE/E for fully enabled autonegotiation: Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. - Page 8 To configure a Gigabit Ethernet interface and enter interface configuration mode on a Cisco 7200 VXR router used as a router-shelf in an AS5800 Universal Access Server, use the interface gigabitethernet router-shelf/slot/port global configuration command.
- Page 9 Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers negotiation negotiation On the Gigabit Ethernet port of the Cisco 7200-I/O-GE+E to configure speed, duplex, and flow control, use the negotiation {forced | auto} interface configuration command. Use the no negotiation auto command to disable automatic negotiation.
- Page 10 Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers negotiation Command Description show interface This command displays status information about the Gigabit Ethernet gigabitethernet interface. 12.1(5)T and 12.2(14) S...
- Page 11 This command was integrated into Cisco IOS Release 12.2(14)S. Usage Guidelines This command is used on the Cisco 7200-I/O-GE+E to display hardware and software information about the Gigabit Ethernet interface.The I/O controller is always found in slot 0. 12.1(5)T and 12.2(14) S...
- Page 12 Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers show controllers gigabitethernet Examples The following example displays sample output of the show controllers gigabitethernet command: Router# show controllers gigabitethernet 0/0 Interface GigabitEthernet0/0 (idb 0x627D8344) Hardware is i82543 (Livengood) A1 network connection mode is AUTO...
- Page 13 Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers show controllers gigabitethernet link_reset=0, tx_carrier_loss=1, fatal_tx_err=0 isl_err=0, wait_for_last_tdt=0 HW addr filter:0x627DB048, ISL disabled, Promiscuous mode on Entry= 0: Addr=0000.C000.4000 (All other entries are empty) i82543 Statistics CRC error Symbol error Missed Packets Single Collision 0...
- Page 14 This command was integrated into Cisco IOS Release 12.2(14)S. Usage Guidelines This command is used on the Cisco 7200-I/O-GE+E to display the configuration status of the Gigabit Ethernet interface. Slot 0 is always reserved for the Gigabit Ethernet port on the I/O controller.
- Page 15 Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers show interfaces gigabitethernet Examples The following example displays sample output of the show interfaces gigabitethernet command: Router# show interfaces gigabitethernet 0/0 GigabitEthernet0/0 is up, line protocol is up Hardware is 82543 (Livengood), address is 00d0.ffb6.4c00 (bia 00d0.ffb6.4c00) Internet address is 11.1.1.3/8...
- Page 16 Cisco 7200-I/O-GE+E and Cisco 7200-I/O-2FE/E Input/Output Controllers show interfaces gigabitethernet 12.1(5)T and 12.2(14) S...