List Of User Programs; Setting The User Programs - Sharp AR-160 Service Manual

AR-205
[8] USER PROGRAMS
The user programs allow the parameters of certain functions to be set,
changed, or canceled as desired.

1. List of user programs

This copier has the following user programs.
Program Program
No. name
Auto clear Sets the auto clear time. The copier
time returns to the initial settings when the
1
auto clear time elapses after the last
copy is made.
Preheat Sets the time that elapses before the
2 mode copier enters the preheat mode after
any operation is made.
Auto power Sets the time that elapses before the
3 shut-off copier enters the auto power shut-off
timer mode after any operation is made.
Stream Enables or disables the stream feeding
4 feeding mode when an optional SPF or RSPF
mode* is installed.
Auto power
Enables or disables the auto power
5 shut-off
shut-off mode.
setting
Border line Enables or disables the border line
for 2 in 1 which is printed in 2 in 1 or 4 in 1
6 or 4 in 1* copying when an optional electronic
sorting kit and an optional SPF or
RSPF are installed.
Rotation Enables or disables rotation of original
7
copy* images.
Auto paper Enables or disables the auto paper
8
select mode selection.
Auto tray Enables or disables the automatic tray
switching switching which occurs when paper in a
9
tray runs out. (This switching cannot
switch to the bypass tray.)
Auditing Enables or disables the auditing mode,
10
mode which controls access to copier.
Account
11 number Registers accounts for auditing mode.
entry
Account
Changes account numbers for auditing
12 number
mode.
change
Account
13 number Deletes accounts for auditing mode.
deletion
Number of
Displays the total number of copies
14 copies per
made against account numbers.
account
Resetting Resets all audit accounts or resets any
15
account desired individual account.
Erase
Sets the amount of the edge erase and
16 width
center erase areas.
adjustment*
Layout in 2
17 Selects a pattern for 2 in 1 copying.
in 1 copy*
Layout in 4
18 Selects a pattern for 4 in 1 copying.
in 1 copy*
Offset of Enables or disables the offset function
paper of the paper output tray. The offset
output tray function can be specified respectively
19
for the upper and lower areas
separated by an optional job separator
tray kit.
Description
8 – 1
Program Program
No. name
Image Enables or disables image rotation
rotation in (180˚) of the front side in one-sided to
20
duplex two-sided copying or two-sided to one-
copying sided copying.
Location of Selects the location of the expanded
22
the margin* margin.
These programs do not affect the copier functions unless certain op-
tional equipment is installed.

2. Setting the user programs

1) Press and hold the light (
all the alarm indicators (
"- -" appears in the copy quantity display.
2) Enter a program number using the numeric keys.
The selected program number will blink in the copy quantity dis-
play.
If a mistake is made in steps 2) to 4), press the CLEAR ( © )
key. The copier will return to step 2).
The program numbers are shown in the table below.
For example, to change the setting of the auto power shut-off timer,
press key 3.
Program name
Auto clear time
Preheat mode
Auto power shut-off timer
Stream feeding mode
Auto power shut-off setting
Border line for 2 in 1 or 4 in 1
Rotation copy
Auto paper select mode
Auto tray switching
Auditing mode
Account number entry
Account number change
Account number deletion
Number of copies per account
Resetting account
Erase width adjustment
Layout in 2 in 1 copy
Layout in 4 in 1 copy
Offset of paper output tray
Image rotation in duplex copying
Location of the margin
3) Press the START key.
For programs 1 to 9 and 16 to 19, the entered program number
will be steadily lit on the left side of the copy quantity display
and the currently selected parameter number for the program
will blink on the right side.
For programs 10 to 15 (programs for auditing accounts), the
display varies with the program number.
4) Select the desired parameter using the numeric keys.
The entered parameter number will blink on the right side of the
copy quantity display.
The parameters are shown in the table below.
Description
) key for more than 5 seconds until
, , , , and ) blink and
Program No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22