Page 1 Follow these instructions to ensure that the product is functioning properly. The images shown in this manual are for illustrative purposes only. For further details, please visit our Company’s website www.zkteco.com. P a g e Copyright©2020 ZKTECO CO., LTD. All rights reserved.
Page 2 ZKTeco supplied equipment vests in and is the property of ZKTeco. The contents hereof should not be used or shared by the receiver with any third party without express written permission of ZKTeco.
Page 3 ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions due to any non-compliance of the instructions contained in this manual (ii) in case of operation of the machine/ unit/equipment beyond the rate limits (iii) in case of operation of the machine and equipment in conditions different from the prescribed conditions of the manual.
Page 4 With years of experience in the industrialization of biometric verifications, ZKTeco was officially established in 2007 and now has been one of the globally leading enterprises in the biometric verification industry owning various patents and being selected as the National High-tech Enterprise for 6 consecutive years.
Page 5 The information which is significant. Care taken to avoid danger or mistakes. The statement or event that warns of something or that serves as a cautionary example. P a g e Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 6 5.1.4 FACE TEMPLATE ........................................37 5.1.5 CARD ............................................. 38 5.1.6 PASSWORD .......................................... 39 5.1.7 PROFILE PHOTO ........................................39 5.1.8 ACCESS CONTROL ROLE ....................................40 ......................................41 EARCH FOR SERS P a g e Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 7 11.1.6 CALLING SHORTCUT SETTINGS ..................................79 11.1.7 ADVANCED SETTINGS ..................................... 81 11.2 ....................................... 81 OORBELL ETTING 11.2.1 CONNECT THE WIRELESS DOORBELL★ ..............................82 11.3 ONVIF S ......................................83 ETTINGS P a g e Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 8 20.2.5 ASSIGNMENT OF EXTENSION NUMBERS AND SIP ACCOUNTS ......................131 20.2.6 PC CLIENT FUNCTIONALITY ..................................137 20.2.7 MAKE A CALL ........................................140 21. CONNECTING TO ZKBIO ZLINK MOBILE APP ................. 146 P a g e Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 9 OLLECTION AND EGISTRATION OF ISIBLE IGHT EMPLATES ......................154 EQUIREMENTS FOR ISIBLE IGHT IGITAL EMPLATE APPENDIX 2 ............................155 ........................................155 RIVACY OLICY ....................................157 FRIENDLY PERATION P a g e Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 10 User Manual Data Security Statement ZKTeco, as a smart product supplier, may also need to know and collect some of your personal information to better assist you in using ZKTeco's goods and services, and will treat your privacy carefully by developing a Privacy Policy.
Page 11 Lightning - Can install external lightning conductors to protect against electrical storms. It stops power-ups destroying the system. The devices should be installed in areas with limited access. P a g e | 10 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 12 1.55 m to 1.85 m is recommended to be 0.3 m to 1.7 m. Users may slightly move forward or backward to improve the quality of facial images captured. P a g e | 11 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 13 Recommendation for Registering a Face Template  When registering a face template, maintain a distance of 40 cm to 80 cm space between the  device and the face template. P a g e | 12 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 14 Do not cover the face template, allow the device to recognize both the eyebrows and the face template. Standby Interface After connecting the power supply, the following standby interface template is displayed: P a g e | 13 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 15 Click ABC to return to the alphabetic keyboard.  Click the input box, virtual keyboard appears.  Click ESC to exit the virtual keyboard.  P a g e | 14 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 16 1:1 verification mode. Click the button on the main screen to enter 1:1 fingerprint verification mode. Input the user ID and press OK. P a g e | 15 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 17 If the user has registered face template, card and password in addition to his/her fingerprints and the verification method is set to Password/Fingerprint/Card/Face template verification, the following screen will appear. Select the fingerprint icon to enter fingerprint verification mode. P a g e | 16 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 18 ID and card number (static QR code only includes card number) information. The QR code can replace a physical card on a specific device to achieve contactless authentication. Please refer to 15.4 Mobile Credential. P a g e | 17 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 19 The 1:1 card verification mode compares the card number in the card induction area with the number associated with the employee's User ID registered in the device. Press in the main interface template to open the 1:1 card verification mode. P a g e | 18 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 20 Select the icon to enter the card verification mode. Place the card in the collection area for verification. Verification is successful: Verification is failed: P a g e | 19 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 22 Password/Fingerprint/Card/Face verification, the following screen will appear. Select the icon to enter the face template verification mode. After successful verification, the prompt box displays "Successfully Verified", as shown below: P a g e | 21 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 24 If the user has registered face template and card in addition to password, and the verification method is set to Password/Fingerprint/Card/Face verification, the following screen will appear. Select the icon to enter password verification mode. P a g e | 23 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 25 Input the password and press OK. The following screen displays, after inputting a correct password and a wrong password respectively. Verification is successful: Verification is failed: P a g e | 24 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 26 But as the employee has registered only the Face template but not the Password, the  verification will not get completed and the Device displays “Verification Failed”. P a g e | 25 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 27 Appearance SenseFace 7A/7C Camera Microphone Near-Infrared Flash 7-inch Touch Screen Speaker Fingerprint Sensor Card Reading Area Tamper Switch Terminal Block USB Interface 0.88"(22.3mm) Reset 4.53"(115.0mm) P a g e | 26 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 28 SenseFace 7 Series User Manual SenseFace 7B Camera Microphone Near-Infrared Flash 7-inch Touch Screen Card Reading Area Tamper Switch Terminal Block Speaker USB Interface 0.88"(22.3mm) Reset 4.53"(115.0mm) P a g e | 27 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 29 DC 12V, 3A Recommended power supply Recommended AC adapter: 12V, 3A.  To share power with other devices, use an AC adapter with higher current ratings.  P a g e | 28 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 30 Note: In LAN, IP address of the server (PC) and the device must be in the same network segment when connecting to the software. 2.3.3 Exit Button, Door Sensor & Auxiliary Connection SmokeDetector +12V DC Exit button Door Sensor P a g e | 29 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 31 2) Device sharing power with the lock +12V DC +12V DC +12V DC 485B 485B 485A 485A F 107 12VOUT 12VOUT F 107 Normally Closed Lock Normally Closed Lock P a g e | 30 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 33 After passing the wires through the wiring hole and connecting them to the device, and then snap the device onto the backplate and push it down into place. Fasten the device to the backplate with a security screw. P a g e | 32 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 34 To set the parameters of the lock and the relevant access control device including Access Control options like time rule, holiday settings, combine verification, and duress option settings. P a g e | 33 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 35 Tap User Mgt. to add an administrator or edit user permissions as a super administrator. If the product does not have an administrator setting, the system will show an administrator setting command prompt every time you enter the device menu. P a g e | 34 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 36 User Management User Registration Click User Mgt. on the main menu. 5.1.1 User ID and Name Tap New User. Enter the User ID and Name. P a g e | 35 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 37 The authentication is based on the authentication method(s) that the super administrator has registered. Please refer to 1.6 Verification Mode. 5.1.3 Fingerprint★ Click Fingerprint to enter the fingerprint registration page. Select the finger to be enrolled. P a g e | 36 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 38 Tap Face in the New User interface to enter the face template registration page. Please face towards the camera and position your face template inside the white guiding box  and stay still during face template registration. P a g e | 37 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 39 On the Card interface, swiping card underneath the card reading area. The card registration will  be successful. If the card is registered already then, the “Duplicate Card” message shows up. The registration  interface is as follows: P a g e | 38 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 40 Note: The password may contain 6 to 8 digits by default. 5.1.7 Profile Photo Tap on Profile Photo in the New User interface to go to the Profile Photo registration page. P a g e | 39 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 41 New users belong to Group 1 by default and can be reassigned to other groups. The device supports up to 99 Access Control groups. • Tap Time Period, to select the time period to use. P a g e | 40 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 43 Delete Profile Photo Only: Deletes the profile photo of the selected user. Display Style Tap on User Mgt. > Display Style to choose the style of All Users interface’s list. P a g e | 42 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 45 Return button. During privilege assignment, the main menu function names will be displayed on the left and  its sub-menus will be listed on its right. P a g e | 44 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 46 But if there is no super administrator registered in the Device, then the device will prompt "Please enroll super admin first!” when enabling the User Role function. P a g e | 45 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 48 Master Unit: When RS485 is used as the function of “Master unit”, the device will act as a master unit, and it can be connected to RS485 card reader. P a g e | 47 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 49 If the communication method is RS232/RS485, you need to input this device ID in the software communication interface. The default TCP COMM Port value is 4370. It can be modified according to the TCP COMM. Port network availability. P a g e | 48 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 50 Choose the appropriate Wi-Fi name from the available list, and input the correct password in  the password interface, and then tap Connect to Wi-Fi (OK). P a g e | 49 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 51 The Wi-Fi can also be added manually if the required Wi-Fi does not show on the list. On this interface template, enter the Tap on Add Wi-Fi Network to add the Wi-Fi network parameters. (The added Wi-Fi manually. network must exist.) P a g e | 50 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 52 The default Gateway address is 0.0.0.0. Can be modified according to the network Gateway availability. The default DNS address is 0.0.0.0. It can be modified according to the network availability. P a g e | 51 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 53 Wiegand Setup To set the Wiegand input or output parameters. Tap Wiegand Setup on the Comm. Settings interface to set the Wiegand input or output parameters. P a g e | 52 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 54 The default value is 1000 microseconds, which can be adjusted within the range Pulse Interval(us) of 200 to 20000 microseconds. ID Type Select between User ID and card number. Various Common Wiegand Format Description Wiegand Format Description P a g e | 53 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 55 “C“ denotes the card number; “E” denotes the even parity bit; “O” denotes the odd parity bit; “F“ denotes the facility code; “M” denotes the manufacturer code; “P” denotes the parity bit; and “S” denotes the site code. P a g e | 54 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 57 To set the network diagnosis parameters. Tap Network Diagnosis on the Comm. Settings interface to set the IP address diagnostic and start the diagnostic parameters. P a g e | 56 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 58 If users need to set date and time manually, disable NTP Server first, and then tap Manual  Data and Time to set date and time and tap Confirm to save. P a g e | 57 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 59 Note: For example, the user sets the time of the device (18:35 on March 15, 2019) to 18:30 on January 1, 2020. After restoring the factory settings, the time of the equipment will remain 18:30 on January 1, 2020. P a g e | 58 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 61 Valid value: 0~9 seconds. Face Template Parameters Tap Face on the System interface to go to the face template parameter settings. Recommended Matching Thresholds High Medium Medium High P a g e | 60 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 62 Improper adjustment of the exposure and quality parameters may severely Notes affect the performance of the device. Please adjust the exposure parameter only under the guidance of the after-sales service personnel of our company. P a g e | 61 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 63 To reduce the process of re-entering user ID, retry is allowed. Fingerprint Used to switch the version of the fingerprint algorithm, Finger VX13.0 or Finger VX10.0. Algorithm P a g e | 62 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 64 15 Connecting to ZKBio Zlink Web Connecting to ZKBio Zlink App.) Set the device as time attendance terminal (T&A PUSH) or access control Device Type terminal (A&C PUSH). P a g e | 63 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 65 The verification result will not show the verification mode after you Verification Mode disable it. Save Photo as After disabling this function, face template re-registration is required after an Template algorithm upgrade. P a g e | 64 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 66 (If the security setting function is turned off, the risk warning will not be displayed when the online update is turned on). P a g e | 65 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 67 (This function does not clear registered user data). Tap Reset on the System interface and then tap OK to restore the default factory settings. P a g e | 66 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 68 Tap Personalize on the Main Menu interface to customize interface settings, voice and bell. User Interface Settings Tap User Interface on the Personalize interface to customize the display style of the main interface. P a g e | 67 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 69 The main screen style can be selected according to the user preference. Voice Settings Tap Voice on the Personalize interface to configure the voice settings. P a g e | 68 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 70 Tap Bell Schedules on the Personalize interface to configure the Bell settings. New bell schedule  Tap New Bell Schedule on the Bell Schedule interface to add a new bell schedule. P a g e | 69 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 71 Delete a bell:  On the All Bell Schedules interface, tap the required bell schedule, and tap Delete, and then tap Yes to delete the selected bell. P a g e | 70 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 72 On the Main Menu, tap Data Mgt. to delete the relevant data in the device. 10.1 Delete Data Tap Delete Data on the Data Mgt. interface to delete the required data. P a g e | 71 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 73 Selecting Delete by Time Range, you need to set a specific time range to delete all data within a specific period. Select Delete by Time Range. Set the time range and click OK. P a g e | 72 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 75 Note: This function needs to be used with the indoor station. Tap SIP Settings on the Video intercom Parameters interface to go to the monitoring SIP settings. P a g e | 74 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 76 Room Number: The device can call the extension number (short number) or Call Number Type room number. SIP Account Number: The device can only call the SIP account. P a g e | 75 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 77 Select the audio encoder for intercom. Both PCMU and PCMA provide better voice quality, but they take up more bandwidth, requiring 64kbps. 11.1.3 Video Options Tap Video Options on the SIP Settings interface. P a g e | 76 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 78 Set the time of call, valid value 30 to 60 seconds. Set the time of intercom, valid value 60 to 120 seconds. It is suggested to Talking Delay(s) set as 60s. P a g e | 77 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 80 Call Address: It is the IP Address of the indoor monitor.  11.1.6 Calling Shortcut Settings Tap Calling Shortcut Settings on the SIP Settings interface. P a g e | 79 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 81 Click Call Mode > Direct Calling Mode> Add, select the indoor monitors that you want to call, then the indoor monitors will be displayed in the list. P a g e | 80 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 82 The value should be set as same as the value of DTMF in the indoor DTMF monitor. 11.2 Doorbell Setting Tap Doorbell Setting on the Video intercom Parameters interface to go to the monitoring doorbell setting. P a g e | 81 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 83 First, power on the wireless doorbell. Then, press and hold the music button for 1.5 seconds until the indicator flashes to indicate it's in pairing mode. After that, click on the SenseFace 7 Series device icon , if the wireless doorbell rings and the indicator flashes, it means the connection is successful.
Page 84 Server Port The default is 8000, and cannot be modified. On the NVR system, click on [Start] > [Menu], then the main menu will pop up. P a g e | 83 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 85 Select the checkbox for the device you want to add and edit the parameters in the corresponding text field, then click on [OK] to add it to the connection list. P a g e | 84 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 86 After adding successfully, the video image obtaining from the device can be viewed in real-time. For more details, please refer to the NVR User Manual. P a g e | 85 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 88 In default settings, new users are allocated into the first group with the default group time zone,  where the access combo is “1” and is set in unlock state by default. P a g e | 87 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 89 Fingerprint + Password, Fingerprint + (Card/User ID), Face Only, Face + Fingerprint, Face + Password, Face + Card, Face + Fingerprint+ Card, and Face + Fingerprint + Password. P a g e | 88 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 90 24-hour clock. Tap the grey box to search the required Time Zone and specify the required Time Zone number (maximum: up to 50 zones). P a g e | 89 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 91  prohibited all day. When the End Time is later than the Start Time, (such as 00:00~23:59), it indicates that the interval is  valid. P a g e | 90 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 92 Tap Holidays on the Access Control interface to set the Holiday access. Add a new holiday:  Tap Add Holiday on the Holidays interface and set the holiday parameters. P a g e | 91 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 93 Click Access Groups on the Access Control interface. Add a New Group  Click New Group on the Access Groups interface and set access group parameters. P a g e | 92 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 94 1 consists of 5 people, and the 5 individuals are from 5 groups, namely, Access Control Group 1 (AC group 1), AC group 3, AC group 5, AC group 6, and AC group 8, respectively. P a g e | 93 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 95 Wiegand signal. The Wiegand format and Output type (User ID / Card Number) adopted by the master device and slave device must be consistent. Tap Anti-passback Setup on the Access Control interface. P a g e | 94 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 97 1 to 999 seconds. Set the 6-digit duress password. When the user enters this duress password for Duress Password verification, an alarm signal will be generated. P a g e | 96 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 98 Note: Only FAT32 format is supported when downloading data using USB disk. Tap USB Manager on the main menu interface. 13.1 USB Download On the USB Manager interface, tap Download. P a g e | 97 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 99 Upload selected photo or upload all photos. The images will be displayed on the screen after upload. User Data To upload all the user information from USB disk into the device. P a g e | 98 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 101 2. Select the time range in which the logs need you want to search for logs of all users, click OK to be searched. without entering any user ID. P a g e | 100 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 102 3. Once the log search succeeds. Tap the login 4. The below figure shows the details of the highlighted in green to view its details. selected log. P a g e | 101 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 103 To test the RTC. The device tests whether the clock works normally and Test Clock RTC accurately with a stopwatch. Tap the screen to start counting and press it again to stop counting. P a g e | 102 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 104 Privacy Policy Note: The current privacy policy's text is only available in Simplified Chinese/ English. However, translation of other multi-language content is underway, with more iterations. P a g e | 103 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 105  Login to ZKBio CVSecurity software, click System > Communication > Communication Monitor to set the ADMS service port, as shown in the figure below: P a g e | 104 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 106 Click Add in operation column, a new window will pop-up. Select Icon type, Area, and Add to Level from each dropdown and click OK to add the device. After the addition is successful, the device will be displayed in the device list. P a g e | 105 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 107 Add Personnel on the Software and Online Fingerprint/Face Registration In the device list, select the device and click Set up > Set as Registration Device. Click Personnel > Person > New: P a g e | 106 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 108 Click Driver Download to install the driver first. Select Remote Registration, then select the IP address of the device and the finger you want to register, click Confirm. P a g e | 107 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 109 Click Access > Device > Control > Synchronize All Data to Devices to synchronize all the data to the device including the new users. Note: For other specific operations, please refer the ZKBio CVSecurity User Manual. P a g e | 108 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 110 Click Device > Device > Add, to add the device on the software. A new window pops-up on clicking Add. Enter the required information about the device and click Confirm, then the added devices are displayed automatically. P a g e | 109 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 111 Fill in all the required fields and click Confirm to register a new user. Click Device > Device, select the device and click Device Menu > Enroll Remotely. P a g e | 110 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 112 Click Device > Device > Data Transfer > Sync Data to the Device to synchronize all the data to the device including the new users. Note: For other specific operations, please refer the ZKBio Time User Manual. P a g e | 111 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 113 Power off the wireless doorbell first, then re-installing the batteries while pressing and holding the music button until the indicator is on, indicating that the unbinding is successful. P a g e | 112 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 114 This function needs to be used with the indoor monitor VT07-B01. On the Indoor Monitor:  Tap Network > to enter the wired network setting interface. (Default password: 123456) P a g e | 113 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 115 Set the IP Address and Gateway of the indoor monitor. (Note: The IP address should be in the same network segment as the device.) Tap Setting > Advance Setting > Device Manage > Add to add the device. P a g e | 114 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 116 Set the related information of the device, then click Save. Device Type: Set as Outdoor Station. Device IP: Enter the IP address of the device. Device Port: 8000. User Name: admin. Password: 123456. P a g e | 115 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 117 User Manual On the Device:  On the Device: Click [Intercom] > [SIP Settings] > [Contact List] > [Add] to add the connected indoor monitors. P a g e | 116 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 118 To enable the video intercom function, click the icon on the device and enter the number or IP address of the indoor monitor in the provided interface. P a g e | 117 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 121 Number: It is the room number that set in the Contact List Menu. Then you can click the icon on the device and select the calling shortcut keys to call the indoor monitor. P a g e | 120 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 122 Mode > Add. Select the IP address of the indoor monitors that you want to call, then the indoor monitors will be displayed in the list. Then you can click the icon on the device to call the indoor monitors directly. P a g e | 121 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 123 ZKBio CVSecurity supports 2 kinds of SIP server: cloud SIP and PBX server, users can choose one according to the actual situation.  Cloud SIP mode: Users do not need to purchase additional SIP server, only need to purchase SIP account permission. P a g e | 122 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 124 After cloud SIP is enabled, the device network needs to be able to connect to the external network before it can be used. ZKBio CVConnect Client Activation Steps  Step 1: Double-click the desktop shortcut key. Jump to browser page. P a g e | 123 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 125 If you already have a Minerva IoT account, you can use it and log in; otherwise click on Register, then jump to Minerva IoT registration page and register your account. P a g e | 124 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 126 If you don't currently have a company, you can choose to create one by clicking Use New Company. Start Activating and wait for 1-2 minutes until the Activation completely. P a g e | 125 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 127 Intercom module. (The adding method can refer to 17. Connect to ZKBio CVSecurity Software) Click Video Intercom > Device Management > Device > New to add the indoor monitor. P a g e | 126 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 128 0. If there are two units, one will be 0 and the other will be 1, and so on. After the addition is successful, the indoor monitor will be displayed in the device list. P a g e | 127 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 129 Extension number: Customize the extension number, it can be up to 8-digit; for example, the number of Room 401, Unit 2, Building 1 can be defined as 01020401 for quick internal identification. P a g e | 128 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 130 If you need to enable different devices or personnel to view a limited number of contacts, you can configure the contact list. Click Extension Management > Contact List > New to create a contact list. P a g e | 129 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 131 Room 1101 is defined as 101. After defining and synchronizing the short number to the device, the device can then dial the short number 101 to call that room. P a g e | 130 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 132 Contacts to assign the contact list to the device; only after the assignment can the device call room numbers/short numbers or make calls through the contact list search. P a g e | 131 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 133 Contacts to assign the contact list to the individual, and after the assignment, the individual can view the contacts in the contact list upon logging into the ZKBio Zexus App. P a g e | 132 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 134 You can click the icon at the right top corner of the ZKBio CVSecurity interface to scan the QR code to install the ZKBio Zexus App. P a g e | 133 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 135 CVConnect client, scan the ZKBio CVConnect Client Information QR Code.) Account & Password: The personnel ID & password (default: 123456); Same account & password as ZKBio CVSecurity. P a g e | 134 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 136 Contacts to assign the contact list to the admin, and after the assignment, the admin can view the contacts in the contact list upon logging into the ZKBio Zexus App. P a g e | 135 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 137 Connected. Then you can directly enter the extension number of the device or click icon to search for the device and call it. P a g e | 136 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 138 To use the BioTalk Pro PC client, please contact the appropriate person for an installation package. Operation Guide Step 1: Configure the SIP account: Click USE A SIP ACCOUNT button. P a g e | 137 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 139 SIP server domian you need to enter on the PC Client.) Password: The extension password of the SIP account for PC client.   Transport: Transportation Protocol, TLS by default. P a g e | 138 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 140 You can open the door by clicking on the keypad and entering the DTMF value of the device, e.g. the default value of ZKTeco device is 1, so you can click on 1 at the keypad. P a g e | 139 Copyright ©...
Page 144 Login to the ZKBio Zexus App, click Application Center > Video Call to enter the video call application, Then you can directly enter the extension number or click the icon to search for the one you want to call. P a g e | 143 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 145 Open the BioTalk Pro client, click the keypad and enter the the SIP Account to make a call. icon > Add Contact to add the contact list manually. You can click the P a g e | 144 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 147 Policy and Data Processing Agreement” and click Sign In to log in to the Mobile App. Note: For more operations, refer to the ZKBio Zlink App's user manual. P a g e | 146 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 148 Once successfully added, the device is displayed in the list of the device interface. Then you can set the access levels and video intercom function as needed. P a g e | 147 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 149 After the setting is successful, you can press the key on the device and enter the Number of the person in the pop-up interface of the device to call him/her. P a g e | 148 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 151 Add Device on the Web Portal Click the icon on the top left corner, and click [Device Center] > [Device] to enter the device setting interface. P a g e | 150 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 152 Then enter the device name and specify the device to a site. Select Site from the drop- down menu. Click [Save] to complete the addition. P a g e | 151 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 153 Note: Wait a moment for the device status to change from “Offline” to “Online”. For more information, please refer to the relevant User Manual. P a g e | 152 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 154 Do not include more than one face template in the capturing area. 10） A distance of 50cm to 80cm is recommended for capturing the template. (The distance is adjustable, subject to body height). P a g e | 153 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 155 The captured person should be clearly visible, natural in color, no harsh shadow or light spot or reflection in face template or background. The contrast and lightness level should be appropriate. P a g e | 154 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 156 Privacy Policy Notice: To help you better use the products and services of ZKTeco (hereinafter referred as "we", "our", or "us") a smart service provider, we consistently collect your personal information. Since we understand the importance of your personal information, we took your privacy sincerely and we have formulated this privacy policy to protect your personal information.
Page 158 The components which contain toxins or harmful elements are included due to the current economic or technical limitations which prevent their replacement with non-toxic materials or elements. P a g e | 157 Copyright © 2025 ZKTECO CO., LTD. All rights reserved.
Page 159 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright © 2025 ZKTECO CO., LTD. All Rights Reserved.

This manual is also suitable for:

Senseface 7a Senseface 7b

ZKTeco SenseFace 7 Series User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for ZKTeco SenseFace 7 Series

Summary of Contents for ZKTeco SenseFace 7 Series

This manual is also suitable for: