Page 1 Follow these instructions to ensure that the product is functioning properly. The images shown in this manual are for illustrative purposes only. For further details, please visit our Company’s website www.zkteco.com. P a g e Copyright©2020 ZKTECO CO., LTD. All rights reserved.
Page 2 ZKTeco supplied equipment vests in and is the property of ZKTeco. The contents hereof should not be used or shared by the receiver with any third party without express written permission of ZKTeco.
Page 3 ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions due to any non-compliance of the instructions contained in this manual (ii) in case of operation of the machine/unit/equipment beyond the rate limits (iii) in case of operation of the machine and equipment in conditions different from the prescribed conditions of the manual.
Page 4 With years of experience in the industrialization of biometric verifications, ZKTeco was officially established in 2007 and now has been one of the globally leading enterprises in the biometric verification industry owning various patents and being selected as the National High-tech Enterprise for 6 consecutive years.
Page 5 The information which is significant. Care taken to avoid danger or mistakes. The statement or event that warns of something or that serves as a cautionary example. P a g e Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 6: Table Of Contents
★..................................... 46 IRELESS ETWORK ................................... 49 LOUD ERVER ETTING ......................................49 IEGAND ETUP 5.6.1 WIEGAND INPUT ......................................50 5.6.2 WIEGAND OUTPUT ....................................52 ....................................53 ETWORK IAGNOSIS P a g e Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 7 ..................................... 97 ODES ....................................97 PTIONS AUTOTEST ............................ 98 SYSTEM INFORMATION ....................... 99 CONNECTING TO ZKBIO ZLINK WEB ..................100 ....................................100 EGISTER CCOUNT ......................................102 EVICE P a g e Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 8 OLLECTION AND EGISTRATION OF ISIBLE IGHT EMPLATES ......................135 EQUIREMENTS FOR ISIBLE IGHT IGITAL EMPLATE APPENDIX 2 ............................136 ........................................136 RIVACY OLICY ....................................138 FRIENDLY PERATION P a g e Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 9: Data Security Statement
User Manual Data Security Statement ZKTeco, as a smart product supplier, may also need to know and collect some of your personal information to better assist you in using ZKTeco's goods and services, and will treat your privacy carefully by developing a Privacy Policy.
Page 10 Lightning – Can install external lightning conductors to protect against electrical storms. It stops power-ups destroying the system. The devices should be installed in areas with limited access. P a g e Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 11: Instruction For Use
1.55 m to 1.85 m is recommended to be 0.3 m to 1.7 m. Users may slightly move forward or backward to improve the quality of facial images captured. P a g e | 10 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 12: Face Template Registration
Please make sure that the face template in the centre of the screen during registration. Please face towards the camera and stay still during face template registration. The screen should look like the image below: P a g e | 11 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 13 If a part of the face template is covered with a hat, a mask, an eye patch, or sunglasses,  authentication may fail. Do not cover the face template, allow the device to recognize both the eyebrows and the face template. P a g e | 12 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 14: Standby Interface
 directly. Click anywhere on the screen apart from the icons, and six shortcut keys appears on the screen, as shown in the figure below: P a g e | 13 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 15: Virtual Keyboard
Note: The punch state options are off by default and need to be changed to other option in the "7.4 Punch States Options" to get the punch state options on the standby screen. Virtual Keyboard P a g e | 14 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 16 Click ABC to return to the alphabetic keyboard.  Click the input box, virtual keyboard appears.  Click ESC to exit the virtual keyboard.  P a g e | 15 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 17: Verification Mode
1:1 verification mode. Click the button on the main screen to enter 1:1 fingerprint verification mode. Input the user ID and press OK. P a g e | 16 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 18 If the user has registered face template and password in addition to his/her fingerprints and the verification method is set to password/fingerprint/face template verification, the following screen will appear. Select the fingerprint icon to enter fingerprint verification mode. P a g e | 17 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 20: Qr Code Verification
ID and card number (static QR code only includes card number) information. The QR code can replace a physical card on a specific device to achieve contactless authentication. Please refer to 17.4 Mobile Credential. P a g e | 19 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 21: Card Verification
User ID registered in the device. Press in the main interface template to open the 1:1 card verification mode. Enter the user ID and click OK. P a g e | 20 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 22 Select the icon to enter the card verification mode. After successful verification, the prompt box displays "Successfully Verified", as shown below: P a g e | 21 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 24 If the user has registered card and password in addition to his/her face template, and the verification method is set to face template/fingerprint/password verification, the following screen will appear. Select the icon to enter the face template verification mode. P a g e | 23 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 25 User Manual After successful verification, the prompt box displays "Successfully Verified", as shown below: If the verification is failed, it prompts “Please adjust your position!”. P a g e | 24 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 26: Password Verification
If the user has registered face template and card in addition to password, and the verification method is set to face template/fingerprint/password verification, the following screen will appear. Select the …. icon to enter password verification mode. P a g e | 25 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 28 SpeedFace-V4L Pro Series User Manual The following screen displays, after inputting a correct password and a wrong password respectively. Verification is successful: Verification is failed: P a g e | 27 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 29: Combined Verification
But as the employee has registered only the Face template but not the Password, the  verification will not get completed and the Device displays “Verification Failed”. P a g e | 28 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 30: Main Menu
Set different type of work. To automatically test whether each module functions properly, including the Autotest LCD screen, audio, microphone, camera, fingerprint sensor and real-time clock. P a g e | 29 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 31 Tap User Mgt. to add an administrator or edit user permissions as a super administrator. If the product does not have an administrator setting, the system will show an administrator setting command prompt every time you enter the device menu. P a g e | 30 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 32: User Management
User Management User Registration Click User Mgt. on the main menu. 3.1.1 User ID and Name Tap New User. Enter the User ID and Name. P a g e | 31 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 33: User Role
Note: If the selected user role is the Super Admin, the user must pass the identity authentication to access the main menu. The authentication is based on the authentication method(s) that the super administrator has registered. Please refer to 1.5 Verification Mode. P a g e | 32 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 34: Fingerprint
Click Fingerprint to enter the fingerprint registration page. Select the finger to be enrolled. Press the same finger on the fingerprint reader three times. Green indicates that the fingerprint was enrolled successfully. P a g e | 33 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 35: Face Template
If the face template is registered already then, the “Duplicate Face” message shows up. The  registration interface is as follows: P a g e | 34 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 36: Card
If the re-entered password is different from the initially entered password, then the device  prompts the message as "Password not match!", where the user needs to re-confirm the password again. P a g e | 35 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 37: Profile Photo
Note: The password may contain 6 to 8 digits by default. 3.1.7 Profile Photo Tap on Profile Photo in the New User interface to go to the Profile Photo registration page. P a g e | 36 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 38: Access Control Role
On the All Users interface, tap on the search bar on the user’s list to enter the required retrieval  keyword (where the keyword may be the user ID, surname or full name) and the system will search for the related user information. P a g e | 37 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 39: Edit User
Note: The process of editing a user is the same as that of adding a user, except that the user ID cannot be modified when editing a user’s detail. The process in detail refers to "3. User Management". P a g e | 38 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 40: Delete User
Delete Profile Photo Only: Deletes the profile photo of the selected user. Display Style Tap on User Mgt. > Display Style to choose the style of All Users interface’s list. P a g e | 39 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 42: User Role
On the User Defined Role interface, toggle Enable Defined Role to enable or disable the user  defined role. Tap on Name and enter the custom name of the role.  P a g e | 41 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 43 But if there is no super administrator registered in the Device, then the device will prompt "Please enroll super admin first!” when enabling the User Role function. P a g e | 42 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 44: Communication Settings
PC are connecting to the same network segment. Tap Ethernet on the Comm. Settings interface to configure the settings. P a g e | 43 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 45: Serial Comm
Serial Comm function facilitates to establish communication with the device through a serial port (RS485/ Master Unit). Tap Serial Comm. on the Comm. Settings interface. P a g e | 44 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 46: Pc Connection
Identity number of the device, which ranges between 1 and 254. Device ID If the communication method is RS232/RS485, you need to input this device ID in the software communication interface. P a g e | 45 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 47: Wireless Network
Choose the appropriate WiFi name from the available list, and input the correct password in the  password interface, and then tap Connect to WIFI (OK). P a g e | 46 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 48 The Wi-Fi can also be added manually if the required Wi-Fi does not show on the list. On this interface template, enter the Tap on Add WIFI Network to add the WIFI network parameters. (The added WIFI manually. network must exist.) P a g e | 47 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 49 The default Gateway address is 0.0.0.0. Can be modified according to the network Gateway availability. The default DNS address is 0.0.0.0. It can be modified according to the network availability. P a g e | 48 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 50: Cloud Server Setting
Wiegand Setup To set the Wiegand input and output parameters. Tap Wiegand Setup on the Comm. Settings interface to set the Wiegand input and output parameters. P a g e | 49 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 52 “C“ denotes the card number; “E” denotes the even parity bit; “O” denotes the odd parity bit; “F“ denotes the facility code; “M” denotes the manufacturer code; “P” denotes the parity bit; and “S” denotes the site code. P a g e | 51 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 53: Wiegand Output
Pulse Interval(us) The time interval between pulses. ID Type Select the ID types as either User ID or card number. P a g e | 52 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 54: Network Diagnosis
To set the network diagnosis parameters. Tap Network Diagnosis on the Comm. Settings interface to set the IP address diagnostic and start the diagnostic parameters. P a g e | 53 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 55: System Settings
Tap System on the Main Menu interface to set the related system parameters to optimize the performance of the device. Date and Time Tap Date Time on the System interface to set the date and time. P a g e | 54 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 56 Tap Daylight Saving Time to enable or disable the function. If enabled, tap Daylight Saving  Mode to select a daylight-saving mode and then tap Daylight Saving Setup to set the switch time. Week mode Date mode P a g e | 55 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 57: Access Logs Settings
Save on failed verification: Photo will be taken and saved only for each failed verification. This function is disabled by default. When enabled, there will be a security Display User Photo prompt. P a g e | 56 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 58: Face Template Parameters
To set the facial template matching time interval as required. Valid value: 0~9 seconds. Face Template Parameters Tap Face on the System interface to go to the face template parameter settings. P a g e | 57 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 59 This value controls the on and off the LED light. The larger the value, the more Value frequently the LED light will be turned on. P a g e | 58 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 61: Video Intercom Parameters
Tap on System > Video Intercom Parameters > QR Code Binding to show the QR code of the device. Click the icon in the upper right corner. P a g e | 60 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 63 Click to open the door remotely. The unlocking record is saved in Me > Message Unlock Center. Note: For other specific operations, please refer to the ZSmart APP User Manual. P a g e | 62 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 64: Connecting To Sip
Enter the server port. Login Name Enter the login name of server. User Name Enter the Username of server. Password Enter the password of server. P a g e | 63 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 65 Note: SIP is an optional feature, when users need to enable SIP server, they need to purchase the server address and password from the distributor. P a g e | 64 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 66 LAN is used, the UDP mode is selected first. Set the IP address on the indoor station, Tap Menu > Advanced > Network > 1. Network > 1. IPv4. P a g e | 65 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 67 Note: If you want to enable this function, please ensure that the SIP Server has been turned off. Tap SIP Settings > Contact List on the Video intercom Parameters interface. P a g e | 66 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 68 It is the dialing number in the configuration data, you can enter the value on Device Number SpeedFace-V4L Pro to call the indoor station quickly for video intercom. P a g e | 67 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 69 Calling > Add. Select the IP addresses of the indoor stations that you want to call, then the indoor stations will be displayed in the list. P a g e | 68 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 70: Device Type Setting
ZKBio Zlink, please refer to 15 Connecting to ZKBio Zlink Web.) Set the device as time attendance terminal (T&A PUSH) or access control Device Type terminal (A&C PUSH). P a g e | 69 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 71: Security Setting
The verification result will not show the verification mode after you Verification Mode disable it. Save Photo as After disabling this function, face template re-registration is required after an Template algorithm upgrade. P a g e | 70 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 72: Usb Upgrade
If no USB disk is inserted in, the system gives the following prompt after you tap USB Upgrade on the System interface. Note: If upgrade file is needed, please contact our technical support. Firmware upgrade is not recommenced under normal circumstances. P a g e | 71 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 73: Factory Reset
(This function does not clear registered user data). Tap Reset on the System interface and then tap OK to restore the default factory settings. P a g e | 72 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 74: Personalize Settings
Menu Timeout (s) The function either can be disabled or set the required value between 60 and 99999 seconds. P a g e | 73 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 75: Voice Settings
Touch Prompt Toggle to enable or disable the keypad sounds. Volume Adjust the volume of the device which can be set between 0 to 100. P a g e | 74 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 76: Bell Schedules
All bell schedules:  Once the bell is scheduled, on the Bell Schedules interface, tap All Bell Schedules to view the newly scheduled bell. P a g e | 75 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 77: Punch States Options
Fixed Mode: Only the manually fixed punch state key will be shown. Users cannot change the status by pressing any other keys. P a g e | 76 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 78: Shortcut Key Mappings
The switch time is set in accordance with the punch state options.  When the punch state mode is set to auto mode, the switch time should be set.  P a g e | 77 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 80: Data Management
To delete attendance data conditionally. Delete Attendance Photo To delete attendance photos of designated personnel. Delete Blocklist Photo To delete the photos taken during failed verifications. P a g e | 79 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 81 Selecting Delete by Time Range, you need to set a specific time range to delete all data within a specific period. Select Delete by Time Range. Set the time range and click OK. P a g e | 80 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 82: Access Control
In default settings, new users are allocated into the first group with the default group time zone,  where the access combo is “1” and is set in unlock state by default. P a g e | 81 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 85: Time Rule Setting
(maximum: up to 50 zones). On the selected Time Zone number interface, tap on the required day (that is Monday, Tuesday etc.) to set the time. P a g e | 84 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 87: Access Groups
Each group can set a maximum of three time zones. By default, newly enrolled users are assigned to Access Group 1; they can be assigned to other access groups. Click Access Groups on the Access Control interface. P a g e | 86 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 88 When the holiday is set to be invalid, the access control time of the personnel in a group is not  affected during holidays. P a g e | 87 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 89: Combined Verification
The Door-unlock combination 3 is set as (09 09 09 09 09), indicating that there are 5 people  in this combination; all of which are from AC group 9. P a g e | 88 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 90: Anti-Passback Setup
Wiegand signal. The Wiegand format and Output type (User ID / Card Number) adopted by the master device and slave device must be consistent. Tap Anti-passback Setup on the Access Control interface. P a g e | 89 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 92 1 to 999 seconds. Set the 6-digit duress password. When the user enters this duress password for Duress Password verification, an alarm signal will be generated. P a g e | 91 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 93: Usb Manager
To download all blocklisted photos (photos taken after failed verifications) Blocklist Photo from the device into USB disk. Work Code★ To download all work code from the device into USB disk. P a g e | 92 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 94: Usb Upload
Download Options★ It is used to encrypt attendance data in the USB disk or delete attendance data. On the USB Manager interface, click Download Options. P a g e | 93 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 95: Attendance Search
2. Select the time range in which the logs need you want to search for logs of all users, click OK to be searched. without entering any user ID. P a g e | 94 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 96 3. Once the log search succeeds. Tap the login 4. The below figure shows the details of the highlighted in green to view its details. selected log. P a g e | 95 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 97: Work Code
It is the digital code of the work code. Users may set a valid value between 1 and 99999999. Name It is the naming of the work code. P a g e | 96 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 98: All Work Codes
In 1: N or 1:1 verification, the system will automatically pop up in the following window. Select the corresponding Word Code manually to verify successfully. P a g e | 97 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 99: Autotest
To test the RTC. The device tests whether the clock works normally and Test Clock RTC accurately with a stopwatch. Tap the screen to start counting and press it again to stop counting. P a g e | 98 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 100: System Information
Privacy Policy Note: The current privacy policy's text is only available in Simplified Chinese/ English. However, translation of other multi-language content is underway, with more iterations. P a g e | 99 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 101: Connecting To Zkbio Zlink Web
If you do not have an account, please click create account to add a new account. Read and agree to User Agreement and Privacy Policy, then click Register. P a g e | 100 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 102 Enter user’s information and set password, then click Register. Set the organization’s name and Organization code, click Create, then complete registration. If you do have an organization, please click Select an Organization. P a g e | 101 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 103: Add Device
Click Me > Organization on the main menu. Click Add icon to add a new person (Repeat adding the department, role and permission, job title, site list, and zone list). P a g e | 102 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 104: Add Device
15.2.2 Add Device Tap COMM. > Ethernet in the main menu on the device to set the IP address and gateway of the device. P a g e | 103 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 105 Click Device Management > Device to enter the Device interface in the ZKBio Cloud Access Click +Add Device button to add a new device. Read and check to the instructions, then click Continue. P a g e | 104 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 106 Enter the device’s serial number, then click Add. (Click System Info > Device Info on the device to view the serial number) Choose a site and a zone, then click Save to finish. P a g e | 105 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 107: Time Slot
Set Door Access Time In ZKBio Cloud Access interface, click Access Control > Door Access Time and click to allocate a time slot to this door. P a g e | 106 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 108: Set Group Access Time
Click to allocate person to this group. Click to allocate a time slot to this group. Click to delete this group. P a g e | 107 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 109: Synchronize Person To Device
Synchronize Person to Device Click Workshop > CloudACC on the main menu to enter the ZKBio Cloud Access interface. Click Access Control > Group Access Time. P a g e | 108 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 111 Click Device Management > Device to enter the Device interface. Choose a device and click Persons in the Device icon to view the person list. P a g e | 110 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 112: User Registration
Click Device Management > Device on ZKBio Cloud Access interface to enter the Device interface. Choose a device and click Persons in the Device icon to view the person list. P a g e | 111 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 113: Register Fingerprint
Click Device Management > Device on ZKBio Cloud Access interface to enter the Device interface. Choose a device and click Persons in the Device icon to view the person list. P a g e | 112 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 114 Submit, then register fingerprint on the device. Click Press the same finger on the fingerprint reader three times. Green indicates that the fingerprint was enrolled successfully. P a g e | 113 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 115: Register Face Template
Choose a device and click Persons in the Device icon to view the person list. Click icon to register face template on the device. P a g e | 114 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 116: Register Password
Click Device Management > Device on ZKBio Cloud Access interface to enter the Device interface. Choose a device and click Persons in the Device icon to view the person list. P a g e | 115 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 117 Click icon to register password on the device. The registration interface is as follows: Note: The password may contain one to eight digits by default. P a g e | 116 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 118: Register Card
Click Device Management > Device on ZKBio Cloud Access interface to enter the Device interface. Choose a device and click Persons in the Device icon to view the person list. Click icon to register password on the device. P a g e | 117 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 120: Data Search
15.6.2 Event Report In ZKBio Cloud Access interface, click Report > Events to check the specific information of all devices’ events. P a g e | 119 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 121: Connecting To Zkbio Zlink App
Open the ZKBio Zlink App and if you do not have an account, please click create account to add a new account. Read and agree to User Agreement and Privacy Policy, then click Register. Enter user’s information and set password, then click Register. P a g e | 120 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 122: Add Person
Add Person Click Me > Organization > Person on the main menu. icon to add a new person. Enter the information, and click Save. Click P a g e | 121 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 123: Add Device
Click Me > Organization > Site (or Zone) on the main menu. icon to add a new site or zone. Enter the information, and click Save. Click P a g e | 122 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 124: Add Device
Click Workshop > CloudACC on the main menu to enter the ZKBio Cloud Access interface. Click Me > Device List to enter the Device interface. And click icon to add a new device. P a g e | 123 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 125 Choose a site and a zone, then click Save to finish. Then click Device, users can view the device status and unlock remotely in this interface. P a g e | 124 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 127: Connect To Zkbio Cvaccess Software
 Login to ZKBio CVAccess software, click System > Communication > Communication Monitor to set the ADMS service port, as shown in the figure below: P a g e | 126 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 128: Add Device On The Software
Click Add in operation column, a new window will pop-up. Select Icon type, Area, and Add to Level from each dropdown and click OK to add the device. P a g e | 127 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 129: Add Personnel On The Software
Fill in all the required fields and click OK to register a new user. Click Access > Device > Control > Synchronize All Data to Devices to synchronize all the data to the device including the new users. P a g e | 128 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 130: Mobile Credential
Tap the QR Code icon to scan the QR code of the new App client. After the client is identified successfully, set the client’s name and tap Connection Test. P a g e | 129 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 131 When using this function for the first time, the App will prompt to authorize the modification of screen brightness settings, as shown in the figure: P a g e | 130 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 132 User Manual The QR code refreshes automatically for every 30s and supports manual refresh. Note: For other specific operations, please refer to ZKBio CVAccess User Manual. P a g e | 131 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 133: Connecting To Wireless Doorbell
Power off the wireless doorbell first, then re-installing the batteries while pressing and holding the music button until the indicator is on, indicating that the unbinding is successful. P a g e | 132 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 134: Settings
Doorbell+Video Intercom: When the user clicks on the doorbell button, the doorbell rings and the device makes a call at the same time. P a g e | 133 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 135: Requirements Of Live Collection And Registration Of Visible Light Face Templates
Do not include more than one face template in the capturing area. 10） A distance of 50cm to 80cm is recommended for capturing the template. (The distance is adjustable, subject to body height). P a g e | 134 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 136: Requirements For Visible Light Digital Face Template Data
The captured person should be clearly visible, natural in color, no harsh shadow or light spot or reflection in face template or background. The contrast and lightness level should be appropriate. P a g e | 135 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 137: Privacy Policy
Privacy Policy Notice: To help you better use the products and services of ZKTeco (hereinafter referred as "we", "our", or "us") a smart service provider, we consistently collect your personal information. Since we understand the importance of your personal information, we took your privacy sincerely and we have formulated this privacy policy to protect your personal information.
Page 139: Eco-Friendly Operation
The components which contain toxins or harmful elements are included due to the current economic or technical limitations which prevent their replacement with non-toxic materials or elements. P a g e | 138 Copyright © 2023 ZKTECO CO., LTD. All rights reserved.
Page 140 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.

ZKTeco SpeedFace-V4L Pro Series User Manual

Data Security Statement

Safety Measures

1 Instruction for Use

2 Main Menu

3 User Management

4 User Role

5 Communication Settings

6 System Settings

7 Personalize Settings

8 Data Management

9 Access Control

10 Usb Manager

11 Attendance Search

12 Work Code

13 Autotest

14 System Information

15 Connecting to Zkbio Zlink Web

16 Connecting to Zkbio Zlink App

17 Connect to Zkbio Cvaccess Software

18 Connecting to Wireless Doorbell

Appendix 1

Appendix 2

Quick Links

Related Manuals for ZKTeco SpeedFace-V4L Pro Series

Summary of Contents for ZKTeco SpeedFace-V4L Pro Series

Table of Contents