Ispring WGB32BM Installation Instructions & User Manual
Heavy duty water filtation systems
Hide thumbs
Also See for WGB32BM:
- Installation instructions & user manual (29 pages) ,
- User manual (16 pages) ,
- User manual (8 pages)
Related Manuals for Ispring WGB32BM
Summary of Contents for Ispring WGB32BM
- Page 1 User Manual of Product 1: iSpring WGB32B 3-Stage Whole House Water Filtration System w/ 20-Inch Sediment and Carbon Block Filters User Manual of Product 2: iSpring UVF55FS Whole House UV Water Filter with Smart Flow Sensor Switch, 55W, 12 GPM...
- Page 19 __________________ __________________ __________________ __________________ ______________________________________________ ____________ ______________ _________________ ___________________________________________ ______ _________________ ___________________________________...
- Page 23 UV has proven to be a quick, reliable, and cost-effective water treatment method for both point-of-use (POU) and point-of- entry (POE) systems. Being a chemical-free, environmentally friendly, and affordable UV water filter system, iSpring’s upgraded UVF55FS UV water filter can protect the whole house against water concerns commonly found in private wells. For...
- Page 24 Components in the Package Model: UVF55FS POE/POU: POE (Point of Entry) Input: 110-120V 50/60Hz UV Bulb: Model#UVB55FS 1. Filter chamber (304SS) 7. UV lamp 2. Clamps 8. Open-end nut 3. Nut 9. Cover Cap 4. Flow switch 10. UV lamp socket 5.
- Page 25 Precautions - Please do not install this product outside or at a place where it is exposed to direct sunlight or freezing temperature. - Please install this product at a place where it is easy to access and maintain. - Avoid jarring/bumping, freezing, overheating, and corrosive chemicals. Specs and Conditions Operating Parameters Maximum Operating Pressure...
- Page 26 Installation Before Installation The unit comes with two ports. Both are 1-inch MNPT and can be used as an inlet or outlet. Please choose the correct fittings to fit your plumbing. It is recommended that you install an inlet valve and an outlet valve before and after the unit for easy maintenance.
- Page 27 Step2– Open the package to check all components inside: Filter Chamber, UV Lamp, Quartz Tube, O-rings, Electronic Ballast, Clamps, Flow switch. Ensure that the Quartz Tube and UV Lamp are clean before installation (clean it with alcohol or mild detergent). Wear soft, non-abrasive gloves to keep any finger marks away from them. Step3–...
- Page 28 Step5– Insert the quartz tube into the filter chamber. Step6– Install O-ring onto the closed end of the quartz tube. Step7– Hand-screw closed-end on the filter Step8– Hand-screw open end nut on the filter chamber chamber(closed end of quartz tube). To protect the O-ring, (open-end of quartz tube).
- Page 29 Step 9– Connect 4-pin electrical socket with UV lamp pins Step10– Carefully insert the UV lamp into the quartz tube tightly. through an open-end nut. Step 12– Insert the flow switch on the outlet; please notice Step 11– Install the cover cap and hand-tighten it onto the water flowing direction.
- Page 30 Step 13– Connect flow switch cable with control switch, close the switch cover. Step 14– Push control switch to the button “AUTO,” the UV lamp will start working automatically when there only water flowing. Push control switch to button “MOVE,” the UV lamp keep working continuedly. Push the control switch button “STOP” to turn off the UV lamp.
- Page 31 Step 15– Select a readily accessible and well-lit location to fix the system. The system should always be located close to the entry and can either be installed horizontally or vertically. Step 16– When all plumbing connections are finished, slowly turn on the water supply and check for leaks. Step 17–...
- Page 32 If this unit falls into the water, turn the main power off and then retrieve it. Do not attempt to use this filter if it has been submerged. Do not operate this unit if it has a damaged cord or plug, if it is malfunctioning or if it has been dropped or been damaged in any manner.
- Page 33 - To clean the quartz sleeve—Use great care when handling the quartz sleeve as it is very fragile; avoid bumping or jarring it. Unplug the power, shut off both inlet and outlet valves, and remove the entire housing from the waterline. Next, drain the water, remove the black rubber cap with the power cord attached, and then remove the lamp from the quartz sleeve.
- Page 34 Warranty This Limited Warranty extends to the original purchaser of the system only. This warranty only covers all manufacturer- supplied items that prove defective in material, workmanship, or factory preparation. This warranty covers parts only; all labor is excluded from this warranty, including, but not limited to, services related to the removal, replacement, installation, adjustment, maintenance, and/or repair of the unit or its component items.
- Page 35 This Limited Warranty does not cover any Manufacturer-supplied items that are defective as a result of the use of improper parts, equipment, or materials. This warranty does not cover alterations or modifications of the unit or failure of a unit caused by such alterations and modifications.
- Page 36 Warranty Registration To register your product for the warranty, please visit our website at 123filter.com and go to the "Warranty Registration" tab. We provide a 30-day money-back guarantee, a 1-year manufacturer warranty, and lifetime tech support for all of our products. However, we do not have the order information from websites other than 123Filter.com (Amazon, Home Depot, etc.), so please be sure to fill in that information upon registration of your system.
- Page 37 Water Systems, LLC Atlanta, Georgia, USA...
Need help?
Do you have a question about the WGB32BM and is the answer not in the manual?
Questions and answers