Canon imageRUNNER ADVANCE DX C568iFZ Installation Manual

Hide thumbs Also See for imageRUNNER ADVANCE DX C568iFZ:

Faq manual (92 pages)

Service manual (98 pages)

page of 154

/ 154
Bookmarks

Quick Links

Download this manual

INSTALLATION

MANUAL

imageRUNNER

ADVANCE DX

C568iFZ/C568iF

C478iFZ/C478iF

Canon

June 28, 2022

Rev. 2

CANON imageRUNNER ADVANCE DX C568/C478 Series Rev. 2 PRINTED IN U.S.A.

Need help?

Do you have a question about the imageRUNNER ADVANCE DX C568iFZ and is the answer not in the manual?

Questions and answers

Summary of Contents for Canon imageRUNNER ADVANCE DX C568iFZ

Page 2 When changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual.
Page 3 Important Notices Symbols The frequently-performed operations are described with symbols in this procedure. Screw Tighten Loosen Packaged Item Unused Parts Remove Install Harness (Common for Guides Connector Power Cord and Clamps) Connect Disconnect Connect Disconnect Remove Install Power Check Push Check the sound Check visually Cleaning...
Page 4 Contents Contents Safety Precautions....................1 Toner Safety............................2 About Toner............................2 Handling Adhered Toner........................2 Points to Note at Installation........................2 Points to Note Before Servicing......................2 Essential Items to Be Performed Before Installation.................2 Power Supply Guidelines........................3 Points to Note when turning ON/OFF the main power................3 illustrations............................
Page 5 Contents Points to Note at Installation.......................106 Checking the Contents........................106 Installation Outline Drawin......................... 107 Installation Procedure........................107 Checking the Operation........................119 Connection Kit-A2/A3/A4 for Bluetooth LE..................121 Points to Note at Installation.......................121 Installation Outline Drawing........................121 Checking the Contents........................122 Installation Procedure........................123 Setting after Installation........................
Page 6 Safety Precautions Toner Safety..........2 Points to Note at Installation....2...
Page 7 Safety Precautions Toner Safety About Toner Toner is a nontoxic matter composed of plastic, iron and a trace of pigments. CAUTION: Never throw toner in flames to avoid explosion. Handling Adhered Toner • Use dry tissue paper to wipe off toner adhered to skin or clothes and wash in water. •...
Page 8 Safety Precautions Power Supply Guidelines • As a general rule, do not use extension cords. If an extension cord must be used, one that meets the rated voltage and current of the product must be used. When using, untie the bundle and plug the power cord into the root to ensure the connection between the power cord and extension cord.
Page 9 Product Lineup Host Machine Options......5...
Page 10 1. Product Lineup Host Machine Options Product name Condition “NFC Kit-E2” on page 23 “Copy Card Reader-F1/Copy Card Reader Attach- It is required when installing Copy Card Reader-F1. ment-B5” on page 45 “Copy Card Reader-F1/Copy Card Reader Attach- Copy Card Reader Attachment-B5 is required. ment-B5”...
Page 11 1. Product Lineup License Products At the time of installation, obtain the license number according to the license certificate included. Then, enter the obtained license number from the Control Panel of the machine. The applicable functions are enabled. There is no physically required installation. Product name Condition Remote Fax Kit-A1...
Page 12 Host Machine Installation of the Host Machine ... 8...
Page 13 2. Host Machine Installation of the Host Machine Host Machine can be installed by the user. See "Getting Started" for details of the installation procedures. Operation when using uniFLOW Online When using uniFLOW Online*, follow the setup procedures on the uniFLOW* Online First Steps Guide (http://www.nt-ware.com/ uFO_FS).
Page 14 2. Host Machine ■ Installation Procedure ● Removing the Covers...
Page 15 2. Host Machine...
Page 16 2. Host Machine ● Installing the IC Card Reader Refer to the table below and install according to the "Reference Procedure" for the IC card reader. NOTE: The installation procedure depends on the shape of the IC card reader. TYPE Shape of IC card reader Reference Procedure “...
Page 17 2. Host Machine...
Page 18 2. Host Machine NOTE: Be sure to adjust the number of cushions according to the thickness of the Card Reader.
Page 19 2. Host Machine NOTE: Go to "Subsequent Work".“Subsequent Work ” on page 15 ● Installing the IC Card Reader （For TYPE 2）...
Page 20 2. Host Machine NOTE: Go to "Subsequent Work".“Subsequent Work ” on page 15 ● Subsequent Work NOTE: Use the screws removed in "Removing the Covers".
Page 21 2. Host Machine NOTE: Wind the cable counterclockwise to store it as needed. NOTE: When installing with the Connection Kit for Bluetooth LE at the same time.
Page 22 2. Host Machine...
Page 23 2. Host Machine CAUTION: Align the White Plate to the Index.
Page 24 2. Host Machine CAUTION: If the White Plate is pressed from top to bottom, it is placed on the Index Sheet, so be sure to press it from bottom to top.
Page 25 2. Host Machine CAUTION: Check that the White Plate is not placed on the Index Sheet with this equipment closed. • Be sure that there is no gap between the White Plate and the Index Sheet. • The gap between the White Plate and the Index Sheet must be 0.3 mm or less as a reference. White Plate White Plate Reader Unit...
Page 26 2. Host Machine Connect the power plug of the host machine to the outlet. Turn ON the Main Power Supply Switch.
Page 27 Host Machine Options NFC Kit-E2.......... 23 Copy Card Reader-F1/Copy Card Reader Attachment-B5....45 Copy Control Interface Kit-A1..... 69 IC Card Reader Box-D1...... 78 Super G3 FAX Board-AT1....106 Connection Kit-A2/A3/A4 for Bluetooth LE..........121 Protection Profile for Hardcopy Devices 1.0 Adaptive Installation Procedure........
Page 28 3. Host Machine Options NFC Kit-E2 Points to Note at Installation • Do not touch the sensor and PCB components of the Control panel. • The parts removed in "Removing the Control Panel" will be used in "Installing the Control Panel". Installation Outline Drawing...
Page 29 3. Host Machine Options Checking the Contents NOTE: The required parts differ depending on the host machine to which this equipment is installed. Use A, B, G, H, I and J for this product. Small 1x TP; M3x6 Small 1x Small 1x Large 1x Large 1x...
Page 30 3. Host Machine Options Installation procedure ■ Removing the Control Panel CAUTION: Be sure to place 5 or more sheets of paper to prevent damage.
Page 31 3. Host Machine Options...
Page 32 3. Host Machine Options...
Page 33 3. Host Machine Options...
Page 34 3. Host Machine Options ■ Installing the NFC Kit...
Page 35 3. Host Machine Options NOTE: The removed parts will be used in step 8.
Page 36 3. Host Machine Options NOTE: The removed part will be used in the next step.
Page 37 3. Host Machine Options NOTE: Use the part removed in the previous step.
Page 38 3. Host Machine Options NOTE: Use the part removed in step 3.
Page 39 3. Host Machine Options NOTE: Position the NFC Cover by aligning it with the marking line to install. NOTE: Install the cable to the NFC PCB as shown in the figure.
Page 40 3. Host Machine Options TP; M3x6 TP; M3x6...
Page 41 3. Host Machine Options Small 1x...
Page 42 3. Host Machine Options CAUTION: Be sure to use appropriate type of screws when installing the removed screws.
Page 43 3. Host Machine Options ■ Installing the Control Panel...
Page 44 3. Host Machine Options...
Page 45 3. Host Machine Options NOTE: Be sure to turn the Cover in the direction of the arrow to install.
Page 46 3. Host Machine Options...
Page 47 3. Host Machine Options CAUTION: Store the excess cable under the Reader.
Page 48 3. Host Machine Options...
Page 49 3. Host Machine Options Setting after Installation 1. Connect the power plug of the host machine to the outlet. 2. Turn ON the main power switch. 3. Eenter service mode and set the value to "1". COPIER > FUNCTION > INSTALL > NFC-USE NOTE: When [System Manager Information Settings] is set, it is required to log in as a system manager in accordance with instructions of the user administrator.
Page 50 3. Host Machine Options Copy Card Reader-F1/Copy Card Reader Attachment-B5 Points to Note at Installation • To install this equipment, the Copy Card Reader Attachment is required. • Pictures and illustrations used in this procedure are from the model without the Finisher. Procedures that are not separately described are same for the model with the Finisher.
Page 51 3. Host Machine Options < Copy Card Reader Attachment-B5 > M3x6 W Sems; M3x14 M3x12 Binding; M4x6 M4x12...
Page 52 3. Host Machine Options Installation Outline Drawing <When the Finisher is not installed> <When the Finisher is installed>...
Page 53 3. Host Machine Options Installation Procedure ■ Removing the Covers <When the Finisher is installed>...
Page 54 3. Host Machine Options ■ Installing the Card Reader Relay Connector Unit...
Page 55 3. Host Machine Options CAUTION: When handling the hard disc, be careful not to vibrateor drop it. NOTE: The removed screw will be used in step 8.
Page 56 3. Host Machine Options NOTE: The removed screw will be used in step 8.
Page 57 3. Host Machine Options...
Page 58 3. Host Machine Options NOTE: Secure the cable to fix the Harness Band as shown in the figure.
Page 59 3. Host Machine Options NOTE: Use the screw removed in step 3 and step 4. CAUTION: Be careful not to let the Relay Cable come in contact with the metal part of the Controller Box. If the Relay Cable come in contact with the metal part of the Controller Box, malfunctions may occur.
Page 60 3. Host Machine Options CAUTION: When handling the hard disc, be careful not to vibrateor drop it.
Page 61 3. Host Machine Options ■ Installing the Covers <When the Finisher is installed>...
Page 62 3. Host Machine Options...
Page 63 3. Host Machine Options ■ Installing the Copy Card Reader...
Page 64 3. Host Machine Options RS Tightening; M4x10...
Page 65 3. Host Machine Options CAUTION: Be sure that the core is inside the Edge Saddle.
Page 66 3. Host Machine Options <When the Finisher is not installed> <When the Finisher is installed>...
Page 67 3. Host Machine Options <When the Finisher is not installed> W sems ;M3x14 <When the Finisher is installed> W sems ;M3x14...
Page 68 3. Host Machine Options <When the Finisher is not installed> TP; M3x6 <When the Finisher is installed> TP; M3x6...
Page 69 3. Host Machine Options CAUTION: To prevent the connector from being disconnected, be sure to place the tie-wrap of the Card Reader External Relay Harness inside of the Connector Cover. TP; M3x6...
Page 70 3. Host Machine Options...
Page 71 3. Host Machine Options NOTE: Attach the cord guides avoiding to overlap the boundary of the cover, ventilation openings and curved surfaces. <When the Finisher is not installed>...
Page 72 3. Host Machine Options <When the Finisher is installed> Checking after Installation 1. Connect the power plug of the host machine to the power outlet. 2. Turn the main power switch ON. 3. Check the model of the Card Reader in service mode. (Default: 0 "Card Reader-F1") COPIER >...
Page 73 3. Host Machine Options 7. Insert a card with a card number that has been registered, and check that the machine operates normally. NOTE: Perform the following operations to change the number of cards (departments) after it has been set. In such a case, counter information for each department is reset.
Page 74 3. Host Machine Options Copy Control Interface Kit-A1 Points to Note at Installation Pictures and illustrations used in this procedure are from the model without the Finisher. Procedures that are not separately described are same for the model with the Finisher. Checking the Contents Installation Outline Drawing...
Page 75 3. Host Machine Options Installation Procedure ■ Removing the Covers <When the Finisher is installed>...
Page 76 3. Host Machine Options ■ Installing the Copy Control Interface Kit...
Page 77 3. Host Machine Options CAUTION: When handling the hard disc, be careful not to vibrateor drop it.
Page 78 3. Host Machine Options CAUTION: Install the extruded side of the D-SUB Support Plate as shown in the figure. Inside...
Page 79 3. Host Machine Options CAUTION: • Be careful not to drop the screws and washers. Dropping a screw or washer may result in damage, so be sure to pick it up. • Install the CC-VI Cable in the direction shown in the figure.
Page 80 3. Host Machine Options CAUTION: When handling the hard disc, be careful not to vibrateor drop it.
Page 81 3. Host Machine Options ■ Installing the Covers <When the Finisher is installed>...
Page 82 3. Host Machine Options...
Page 83 3. Host Machine Options IC Card Reader Box-D1 Points to Note at Installation • When installing this equipment, the IC Card Reader (sales company's option) is required. Use an extension cable for the card reader cable. Checking the Contents TP; M3x6 P Tightening TP;...
Page 84 3. Host Machine Options Installation Outline Drawing <When the Finisher is not installed> <When the Finisher is installed>...
Page 85 3. Host Machine Options Installation Procedure ■ Preparation NOTE: Remove the claw on Bottom Cover of the IC Card Reader Box Unit by pinching it in the direction of the arrow. Bottom Cover Lower Cover NOTE: The removed Bottom Cover will be used in “Installing the IC Card Reader Box”.
Page 86 3. Host Machine Options CAUTION: Do not install the IC Card Reader Support Plate in the opposite direction. TP; M3x6...
Page 87 3. Host Machine Options ■ Installing the IC Card Reader Box (When the Finisher is not installed)
Page 88 3. Host Machine Options...
Page 89 3. Host Machine Options...
Page 90 3. Host Machine Options TP; M3x6...
Page 91 3. Host Machine Options...
Page 92 3. Host Machine Options...
Page 93 3. Host Machine Options CAUTION: When cutting off the part, be sure not to make burrs.
Page 94 3. Host Machine Options...
Page 95 3. Host Machine Options NOTE: Use the Bottom Cover removed in "Preparation". CAUTION: When installing the Bottom Cover, be careful not to trap cables.
Page 96 3. Host Machine Options NOTE: Store the excess cable in the box.
Page 97 3. Host Machine Options Connect the power plug to the outlet. Turn ON the Main Power Switch.
Page 98 3. Host Machine Options ■ Installing the IC Card Reader Box (When the Finisher is Installed)
Page 99 3. Host Machine Options...
Page 100 3. Host Machine Options...
Page 101 3. Host Machine Options TP; M3x6...
Page 102 3. Host Machine Options...
Page 103 3. Host Machine Options...
Page 104 3. Host Machine Options CAUTION: Be sure not to make burrs when cutting the part.
Page 105 3. Host Machine Options...
Page 106 3. Host Machine Options...
Page 107 3. Host Machine Options...
Page 108 3. Host Machine Options NOTE: Use the Bottom Cover that was removed in “Preparation”. CAUTION: When installing the Bottom Cover, be careful not to trap the cable.
Page 109 3. Host Machine Options NOTE: Store the excess length of the cable inside the box.
Page 110 3. Host Machine Options Connect the power plug to the outlet. Turn ON the Main Power Switch.
Page 111 3. Host Machine Options Super G3 FAX Board-AT1 Points to Note at Installation • When installing the Super G3 2nd Line Fax Board and this equipment at the same time, check the parts included in the package, and install them following the Installation Procedure for Super G3 2nd Line Fax Board. •...
Page 112 3. Host Machine Options Installation Outline Drawin Installation Procedure ■ Removing the Covers...
Page 113 3. Host Machine Options CAUTION: Do not insert a screwdriver into the hole when removing the Small Cover.
Page 114 3. Host Machine Options NOTE: When the Cassette Pedestal is not installed, go to step 4.
Page 115 3. Host Machine Options NOTE: When the Cassette Pedestal is installed, go to step 3. When the Cassette Pedestal is not installed, perform from step 5.
Page 116 3. Host Machine Options...
Page 117 3. Host Machine Options ■ Installing the FAX Unit...
Page 118 3. Host Machine Options CAUTION: When handling the HDD, be careful not to vibrate or drop it.
Page 119 3. Host Machine Options...
Page 120 3. Host Machine Options...
Page 121 3. Host Machine Options ■ Subsequent Work NOTE: If the Cassette Pedestal is not installed, skip the following 5 and 6.
Page 122 3. Host Machine Options NOTE: This step is only for Taiwan. FAX Approval Label...
Page 123 3. Host Machine Options NOTE: • This step is only for Europe. • Do not connect the telephone cord (2 core) to PTT plugs. • Connect the PTT cable (6 core) to the PTT Plug appropriate for the country/region.
Page 124 3. Host Machine Options Connect the power plug to the outlet. Turn ON the Main Power Supply Switch. Checking the Operation ■ Type Setting Select the country/region of the FAX Board in Service Mode: FAX > Type > TYPE This setting performs the parameter settings to match the communication specification of the country/region. 1.
Page 125 3. Host Machine Options 1. Set the user telephone number. [Settings/Registration] > [Function Settings] > [Send] > [Fax Settings] > [Set Line] > [Line 1] > [Register Unit Telephone Number] > Enter the fax number > [OK] 2. Set Type of telephone line. [Settings/Registration] >...
Page 126 3. Host Machine Options Connection Kit-A2/A3/A4 for Bluetooth LE Points to Note at Installation • When installing the IC Card Reader Installation Kit at the same time, install this equipment first. Installation Outline Drawing...
Page 127 3. Host Machine Options Checking the Contents NOTE: • Use A, C, D, G and H for this product. • * mark item may not be included. *1 x With Finisher; Long Type P Tightening; W Sems; TP; M3x6 M3x8 M3x6 Without Finisher;...
Page 128 3. Host Machine Options Installation Procedure...
Page 129 3. Host Machine Options <When the Finisher is installed>...
Page 130 3. Host Machine Options...
Page 131 3. Host Machine Options...
Page 132 3. Host Machine Options...
Page 133 3. Host Machine Options...
Page 134 3. Host Machine Options CAUTION: Be sure to install the Grounding Wire in the correct orientation. P Tightening; M3x8...
Page 135 3. Host Machine Options With Finisher; Without Finisher; Long Type Short Type P Tightening; M3x8...
Page 136 3. Host Machine Options...
Page 137 3. Host Machine Options...
Page 138 3. Host Machine Options CAUTION: Align the White Plate with the Index.
Page 139 3. Host Machine Options CAUTION: If the White Plate is pressed from top to bottom, it is placed on the Index Sheet, so be sure to press it from bottom to top.
Page 140 3. Host Machine Options CAUTION: Check that the White Plate is not placed on the Index Sheet with this equipment closed. • Be sure that there is no gap between the White Plate and the Index Sheet. • The gap between the White Plate and the Index Sheet must be 0.3 mm or less as a reference. White Plate White Plate Reader Unit...
Page 141 3. Host Machine Options NOTE: Pull out the Grounding Wire that was passed through the hole in step 18, and connect it. CAUTION: Be sure to install the Grounding Wire in the correct orientation. W Sems; M3x6...
Page 142 3. Host Machine Options NOTE: Pull out the cable that was passed through the hole in step 18.
Page 143 3. Host Machine Options <When the Finisher is not installed>...
Page 144 3. Host Machine Options <When the Finisher is installed>...
Page 145 3. Host Machine Options...
Page 146 3. Host Machine Options <When the Finisher is installed>...
Page 147 3. Host Machine Options...
Page 148 3. Host Machine Options 10 mm...
Page 149 3. Host Machine Options NOTE: Affixing the Approval Label is not required in countries/regions other than the following. <For US> Affix it over the number on the Wireless LAN Approval Label. Setting after Installation 1. Connect the power plug of the host machine to the outlet. 2.
Page 150 “Protection Profile for Hardcopy Devices 1.0” in the state at the time of CC certification (HCD-PP) evaluation (firmware). • “Canon imageRUNNER ADVANCE ADVANCE DX C568/C478 series” is described as the targeted product in this setting procedure. Specific target models are listed in “imageRUNNER ADVANCE DX C568/C478 series is a necessary product to provide in the state at the time of CC certification (HCD-PP) evaluation”...
Page 151 3. Host Machine Options CAUTION: Since the firmware at the time of CC certification evaluation is set to the installed initial state, the information set in the device is initialized. 2. Initialize HDD and setting values. 1. Set HDD initialization reservation. •...
Page 152 This host machine was installed according to the configuration evaluated and certified by CC certification. This host machine is a CC-certified MFP host machine of Canon imageRUNNER DX xxxxx with FAX. * Inform that xx is the model name C568iFZ or C478i and so on purchased.
Page 153 3. Host Machine Options ■ Tasks that may be required at a later date << Clear Disk Encryption Key>> Assumed Implementation Case) - This is intended to be implemented at the request of an administrator concerned about the leakage of remaining data in the SSD when the host machine is leased back or disposed of, or when there is an organization change or layout change.
Page 154 Revision Revision Chapter Category Product Name Reference Remarks First Edition Installation manual 1 Product Lineup Add Con- Protection Profile for Hardcopy De- “ Host Machine Options” on page 5 tents vices 4 Host Machine Add Con- Protection Profile for Hardcopy De- “Protection Profile for Hardcopy De- Options tents...

This manual is also suitable for:

Imagerunner advance dx c568if Imagerunner advance dx c478ifz Imagerunner advance dx c478if