Crestron HD-TX-101 Series Instructions Manual

HD-TX/HD-RX 101 Series
DM Lite Transmitters and Receivers
HD-TX/HD-RX 101 Series
DM Lite Transmitters and Receivers
DO Install the Device
DO Install the Device
The Crestron ® HD-TX/HD-RX 101 Series consists of transmitters and
receivers that are available as surface-mount devices and wall plates.
The surface-mount devices consist of the HD-TX-101-C-E and
The Crestron
HD-TXC-101-C-E transmitters and the HD-RX-101-C-E and
HD-RXC-101-C-E receivers. The wall plates consist of the
receivers that are available as surface-mount devices and wall plates.
HD-TX-101-C-1G-E and HD-TXC-101-C-1G-E transmitters and the
HD-RX-101-C-1G-E and HD-RXC-101-C-1G-E receivers.
The surface-mount devices consist of the HD-TX-101-C-E and
Install the Surface-Mount Device
HD-TXC-101-C-E transmitters and the HD-RX-101-C-E and
Mount the device onto a flat surface or rack rail.
HD-RXC-101-C-E receivers. The wall plates consist of the
Mount onto a Flat Surface
HD-TX-101-C-1G-E and HD-TXC-101-C-1G-E transmitters and the
Using four mounting screws (not included), mount the device onto a flat
surface such as a wall.
HD-RX-101-C-1G-E and HD-RXC-101-C-1G-E receivers.
Wall Mounting
Install the Surface-Mount Device
Mount the device onto a flat surface or rack rail.
Mount onto a Flat Surface
Using four mounting screws (not included), mount the device onto a flat
surface such as a wall.
Wall Mounting
Mount onto a Rack Rail
Mount the device onto the front or rear rail of a rack. Position either the
left or right mounting flange of the device so that the holes align with the
holes in the rack. Then, secure the device to the rack using two mounting
screws (not included).
Rail Mounting
Mount onto a Rack Rail
Mount the device onto the front or rear rail of a rack. Position either the
left or right mounting flange of the device so that the holes align with the
holes in the rack. Then, secure the device to the rack using two mounting
screws (not included).
Rail Mounting
DO GUIDE
HD-TX/HD-RX 101 Series consists of transmitters and
®
Install the Wall Plate
Install the wall plate into a 1-gang electrical box (not included):
1. Connect the rear of the wall plate by doing either of the following:
• If the wall plate is a transmitter, connect the TO RX port.
• If the wall plate is a receiver, connect the FROM TX port.
NOTES:
• For the 24 Vdc power connection, connect a power pack to
either a transmitter or receiver. Do not connect a power pack
to both devices simultaneously. Power is transmitted over the
cable that connects the TO RX port on the transmitter to the
FROM TX port on the receiver.
Power packs are not included with the wall plates but are
included with the surface-mount devices. When a wall plate
connects to a surface-mount device, power both devices
by connecting the included power pack to the
surface-mount device.
• Cabling that connects the TO RX port to the FROM TX port is
designed for intrabuilding use only.
2. Using a Phillips screwdriver (not included), attach the device to
the electrical box using the two included #6-32 x ¾ inch truss
combo head screws.
3. Attach a Crestron FP-G1 Series decorator-style faceplate
(sold separately) to the front panel of the device using two
screws (not included).
Installation into Electrical Box
24 V
1.25 A:
From power pack
(not included)
OR FROM TX
TO RX
(Receiver):
(Transmitter):
From TO RX
To FROM TX
link output port
link input port
of transmitter
of receiver