HP ElitePad 1000 G2 Disassembly Instructions

Also See for ElitePad 1000 G2:

Maintenance and service manual (126 pages)

User manual (82 pages)

Quickspecs (25 pages)

Table of Contents

Contents

1 Items Requiring Selective Treatment
2 Tools Required
3 Product Disassembly Process
4 Documents / Resources
- 4.1 Download manual

HP ElitePad 1000 G2 Disassembly Instructions

Items Requiring Selective Treatment

Items listed below are classified as requiring selective treatment.
Enter the quantity of items contained within the product which require selective treatment in the right column, as applicable.

Item Description	Notes	Quantity of items included in product
Printed Circuit Boards (PCB) or Printed Circuit Assemblies (PCA)	With a surface greater than 10 sq cm Mother board	4
Batteries	All types including standard alkaline and lithium coin or button style batteries battery	2
Mercury-containing components	For example, mercury in lamps, display backlights, scanner lamps, switches, batteries
Liquid Crystal Displays (LCD) with a surface greater than 100 sq cm	Includes background illuminated displays with gas discharge lamps LCD	1
Cathode Ray Tubes (CRT)
Capacitors / condensers (Containing PCB/PCT)
Electrolytic Capacitors / Condensers measuring greater than 2.5 cm in diameter or height
External electrical cables and cords	Power cords, Adapter	1
Gas Discharge Lamps
Plastics containing Brominated Flame Retardants
Components and parts containing toner and ink, including liquids, semi-liquids (gel/paste) and toner	Include the cartridges, print heads, tubes, vent chambers, and service stations.
Components and waste containing asbestos
Components, parts and materials containing refractory ceramic fibers
Components, parts and materials containing radioactive substances

Tools Required

List the type and size of the tools that would typically be used to disassemble the product to a point where components and materials requiring selective treatment can be removed.

Tool Description	Tool Size (if applicable)
Small Philips head screw driver	Philip #0
service fixture
Scraper
Description #4
Description #5

Product Disassembly Process

List the basic steps that should typically be followed to remove components and materials requiring selective treatment:

<< SuperJacket disassembly method >>
1. Remove screw and remove front cover, rear cover
2. Remove Slate(Astro2)
<< Astro2 disassembly >>
1. Remove bumper ring sub assy.
2. Remove Battery cable, EDP FPC & T/S FPC
3. Remove Powe Board assy, Audio Board Assy and Power FPC
4. Remove Battery Pack
5. Remove Remove Docking support bracket
6. Remove Speaker module
7. Remove WWAN module & GPS module
8. Remove WLAN module
9. Remove MB Assy
10. Remove WLAN Antenna & WWAN Main/Aux Antenna
11. Divide Power Board assy (remove 1st Mic, 8M camera, Volume board)
12. Divide MB assy (remove Docking FPC, 2nd Mic, 2M CAMERA)
<< Tank disassembly >>
1. Remove Battery - 4 screws near the edge closest to the port edge.
2. Remove all feet and front panel by prying or pulling to release flexible plastic holders.
3. Remove 6 Screws from the top side of the top piece of plastic (SJ671-40001). 2 are on top edge 4 are on the bottom near the expansion ports. There is also 4 screws throug the bottom side (2 on each short edge) There is adhesive so just pull until top piece releases.
4. Cut or puncture with screw driver and remove plastic film behind the battery. It is attached by adhesive and must be peeled off to reveal the screws that attach to the middle and rear plastic pieces.
5. Middle plastic piece has 8 screws to remove 4 each along the long edges and 1 each on the short edge.
6. Remove 6 screws from the small L shaped plastic (SJ671-40012).
7. Remove 6 screws from near round piece in center (SJ671-40010).
8. Multiple small PCBs are between the middle and back plastic pieces. Flat cables and copper sheilding can be removed as needed bt pulling tape and pulling.
9. Attached to SJ674-40010 are several pieces to seatate. Twist the round SD coard cover to remove.
10. After SJ674-40010 is separated from back panel the metal ring should fall off
11. Remove Nylon springs
12. Remove all glass, soft plastic with a pick or comparable tool.
13. Remove all metal screw keeps and metal attached the double sided tape with a pick or comparable tool..

Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items contained in the product that require selective treatment (with descriptions and arrows identifying locations).