Table of Contents
Advertisement
Input/output ratings
Analog audio input/output
MIC INPUTS (Balanced) terminals (1-8)
Connector: XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance: 2.4 kΩ
Nominal input level:
–60 dBu (When input gain konb is at maximum )
–4 dBu (When input gain knob is at minimum)
Maximum input level:
+12 dBu (When input gain knob is at minimum)
INST IN (Unbalanced) terminals (7-8)
Connector: 6.3 mm (1/4") Standard phone jack
Input impedance: 1 MΩ
Nominal input level:
–56 dBu (When input gain konb is at maximum )
0 dBu (When input gain knob is at minimum)
Maximum input level:
+16 dBu (When input gain knob is at minimum)
LINE IN (Balanced) terminals (9-14)
Connector: 6.3 mm (1/4") TRS Standard phone jack
(Tip: HOT, Ring: COLD, Sleeve: GND)
Input impedance: 10 kΩ
Nominal input level:
–10 dBV/+4 dBu
Maximum input level:
+6 dBV/+ 20 dBu
LINE OUTPUTS (Balanced) terminal
Connector: 6.3 mm (1/4") TRS Standard phone jack
(Tip: HOT, Ring: COLD, Sleeve: GND)
Output impedance: 100Ω
Nominal output level:
+4 dBu
Maximum output level:
+20 dBu
MONITOR OUT (Balanced) terminal
Connector: 6.3 mm (1/4") TRS Standard phone jack
(Tip: HOT, Ring: COLD, Sleeve: GND)
Output impedance: 100Ω
Nominal output level:
+4 dBu
Maximum output level:
+20 dBu
INSERT (Unbalanced) terminal
Connector: 6.3 mm (1/4") TRS Standard phone jack
(Tip: SEND, Ring: RECEIVE, Sleeve: GND)
Output impedance: 100Ω
Nominal output level:
–2 dBu
Maximum output level:
+14 dBu
Input impedance: 10 kΩ
Nominal input level
8 – Specifications
–2 dBu
Maximum input level:
+14 dBu
PHONES jack
Connector: 6.3 mm (1/4") Standard Stereo phone jack
Maximum output level:
100 mW + 100 mW or more
(THD + N less than 1%, 32Ω load)
Digital audio input/output
DIGITAL IN (COAXIAL) terminal
Connector: RCA pin jack
Compatible signal format: IEC60958-3 (S/PDIF)
DIGITAL OUT (COAXIAL) terminal
Connector: RCA pin jack
Compatible signal format: IEC60958-3 (S/PDIF) or
AES3-2003 (AES/EBU), selectable using control panel
Control input/output
USB terminal
Connector: USB B type 4 pin
Format:
USB 2.0 High speed (480 MHz)
Audio performance
Frequency response
20 Hz - 20 kHz, ±1.0 dB (44.1/48 kHz) (
)
MONITOR OUTPUT
20 Hz - 40 kHz, +0.5/–2.0 dB (88.2/96 kHz) (
)
MONITOR OUTPUT
Signal-to-noise ratio
90 dB (
to
LINE IN
MONITOR OUTPUT
A-weighted)
Total harmonic distortion
Less than 0.01% (
LINE IN
+20 dBu input, 20 kHz LPF)
Computer requirements
Windows
Supported Operating system
Windows:
Windows XP 32 bit SP2 or later
Windows XP 64 bit SP2 or later
Windows Vista 32 bit SP2 or later
Windows Vista 64 bit SP2 or later
to
MIC
to
MIC
, 20 kHz LPF +
to
, 1 kHz,
MONITOR OUTPUT
19
TASCAM US-2000
Advertisement
Table of Contents
