Table of Contents
Advertisement
Heliarc SR-26, SR-26V, SR-26-F
Instruction manual and Spare parts list
PLEASE READ AND UNDERSTAND ALL INSTRUCTION BEFORE USE. RETAIN
THIS MANUAL FOR FUTURE REFERENCE.
Manual Number: M003
Revision Date: 2023-07-10
Revision Number: B
Language: English
Heliarc SR-9, SR-9V
Heliarc SR-17, SR-17V
Complete User Manual at:
Advertisement
Table of Contents
Related Manuals for ESAB Heliarc SR-17
Summary of Contents for ESAB Heliarc SR-17
- Page 1 Heliarc SR-9, SR-9V Heliarc SR-17, SR-17V Heliarc SR-26, SR-26V, SR-26-F Instruction manual and Spare parts list PLEASE READ AND UNDERSTAND ALL INSTRUCTION BEFORE USE. RETAIN THIS MANUAL FOR FUTURE REFERENCE. Complete User Manual at: Manual Number: M003 Revision Date: 2023-07-10...
-
Page 2: Table Of Contents
.......................... MAINTENANCE ..........................Daily ........................ TROUBLESHOOTING ....................... ORDERING SPARE PARTS ......................... ORDERING NUMBERS ......................SPARE PARTS - SR-9, SR-9V ......................SPARE PARTS - SR-17, SR-17V ................... SPARE PARTS - SR-26, SR-26V, SR-26-F M003 - 2 - © ESAB AB 2023... -
Page 3: Safety
Sheets (SDSs). Safety precautions Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace. - Page 4 If equipped with ESAB cooler Use ESAB approved coolant only. Non-approved coolant might damage the equipment and jeopardize product safety. In case of such damage, all warranty undertakings from ESAB cease to apply. For ordering information, see the "ACCESSORIES" chapter in the instruction manual.
- Page 5 For further information contact the nearest ESAB dealer. ESAB has an assortment of welding accessories and personal protection equipment for purchase. For ordering information contact your local ESAB dealer or visit us on our website. M003 - 5 -...
-
Page 6: Introduction
○ Ø 1.6 mm (0.063 in.) Heliarc SR 9 ○ Ø 2.4 mm (0.094 in.) Heliarc SR 17 ○ Ø 2.4 mm (0.094 in.) Heliarc SR 26 • Safety instructions • Instruction manual M003 - 6 - © ESAB AB 2023... -
Page 7: Technical Data
The duty cycle is valid for 40 °C / 104 °F, or below. Enclosure class The IP code indicates the enclosure class, i.e. the degree of protection against penetration by solid objects of 2.5 mm Ø and greater. Omitting second characteristic numeral. M003 - 7 - © ESAB AB 2023... -
Page 8: Operation
150–210 120–230 (0.094 in.) (0.386/0.441/0.500 in.) 3.2 mm 11.2/12.7 mm 130–180 140–190 150–205 220–320 200–305 (0.126 in.) (0.441/0.500 in.) 4.0 mm 12.7 mm 180–230 200–250 180–270 330–420 250–420 (0.157 in.) (0.500 in.) M003 - 8 - © ESAB AB 2023... -
Page 9: Grinding
Always make sure that the torch head is supported by the thumb when you bend. This prevents damage at sharp bending. Valve torches CAUTION! Do not operate TIG torches with an integrated valve in the torch neck on welding systems equipped with an ignition and stabilisation device. M003 - 9 - © ESAB AB 2023... -
Page 10: Maintenance
Check that the shielding gas flows evenly and without restriction. • Check that the electrode is undamaged and that the electrode has been ground to the correct angle. • Check the coolant flow at the unit's return line (liquid-cooled versions only). M003 - 10 - © ESAB AB 2023... -
Page 11: Troubleshooting
Insufficient or total lack of screens. shielding gas. • Clean or replace. • It is too draughty at the welding site. • Welding spray has fastened on the gas lens or the gas hood. M003 - 11 - © ESAB AB 2023... -
Page 12: Ordering Spare Parts
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see esab.com. When ordering, please state product type, serial number, designation and spare part number in accordance with the spare parts list. - Page 13 APPENDIX APPENDIX M003 - 13 - © ESAB AB 2023...
-
Page 14: Ordering Numbers
Ridgid Valve Flexible 4 m / 8 m / 12.5 ft 25 ft 0700 026 600 ESAB Heliarc SR-9 12.5 ft 0700 026 601 ESAB Heliarc SR-9 25 ft 0700 026 604 ESAB Heliarc SR-9V 12.5 ft 0700 026 605 ESAB Heliarc SR-9V 25 ft 0700 026 610 ESAB Heliarc SR-17 12.5 ft... - Page 15 * here. Make sure to use a manual with a serial number or software version that corresponds with the product, see the front page of the manual. Technical documentation is available on the Internet at: www.esab.com M003 - 15 - © ESAB AB 2023...
-
Page 16: Spare Parts - Sr-9, Sr-9V
Torch head valved, SR-9V 0700 300 581 Gas valve 0700 025 631 Handle, H100 0700 025 623 TIG connector 3550 0700 025 993 Gas hose 0700 025 975 Hose clamp with ring M003 - 16 - © ESAB AB 2023... -
Page 17: Spare Parts - Sr-17, Sr-17V
Torch head valved, SR-17V 0700 300 581 Gas valve 0700 025 631 Handle, H100 0700 025 623 TIG connector 3550 0700 025 993 Gas hose 0700 025 975 Hose clamp with ring M003 - 17 - © ESAB AB 2023... -
Page 18: Spare Parts - Sr-26, Sr-26V, Sr-26-F
Torch head valved, SR-26V 0700 025 599 Gas valve 0700 025 632 Handle, H200 0700 025 623 TIG connector 3550 0700 025 993 Gas hose 0700 025 975 Hose clamp with ring M003 - 18 - © ESAB AB 2023... - Page 19 APPENDIX M003 - 19 - © ESAB AB 2023...
- Page 20 ESAB AB ESAB Corporation ESAB Holdings Ltd Lindholmsallén 9 2800 Airport Road 322 High Holborn Box 8004 Denton, TX 76207 WC1V 7PB 402 77 Gothenburg London, Great Britain Sweden Phone +1 800 378 8123 Phone +44 (0) 1992 768515 Phone +46 (0) 31 50 90 00 For contact information visit http://esab.com...
Need help?
Do you have a question about the Heliarc SR-17 and is the answer not in the manual?
Questions and answers