Worx WG304.2 Manual
  1. Manuals
  2. Brands
  3. Worx Manuals
  4. Chainsaw
  5. WG304.2
  6. Manual

Worx WG304.2 Manual

Electric chain saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Electric Chain Saw
WG300 WG303.1
WG304.1 WG304.2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WG304.2 and is the answer not in the manual?

Questions and answers

Related Manuals for Worx WG304.2

Summary of Contents for Worx WG304.2

  • Page 1 Electric Chain Saw WG300 WG303.1 WG304.1 WG304.2...
  • Page 2 14 15 16...
  • Page 3 18 8 Bar / F: Bar Run Screwdriver along the chain to check for kinks Ratchet mechanism...
  • Page 4 Injecting grease to lubricate...

  • Page 5: Product Safety

    PRODUCT SAFETY explosive atmospheres, such as in the presence of flammable liquids, gases WARNING: Some dust created by or dust. Power tools create sparks which power sanding, sawing, grinding, may ignite the dust or fumes. drilling and other construction activities c) Keep children and bystanders contains chemicals known to the state of away while operating a power tool.

  • Page 6: Chain Saw Safety Warnings

    Always wear eye protection. Protective the power tool accidentally. d) Store idle power tools out of the equipment such as dust mask, non- reach of children and do not allow skid safety shoes, hard hat, or hearing persons unfamiliar with the power protection used for appropriate conditions tool or these instructions to operate will reduce personal injuries.

  • Page 7: Causes And Operator Prevention Of Kickback

    left hand on the front handle. Holding are slippery causing loss of control. 12. Cut wood only. Do not use chain the chain saw with a reversed hand saw for purposes not intended. For configuration increases the risk of personal example: do not use chain saw for injury and should never be done.
  • Page 8 cause chain breakage and/or kickback. - Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback. (B) CONNECT PLUG AND RECEPTACLE SAFETY RULES FOR EXTENSION CORD Make sure your extension cord is in good SAVE THESE INSTRUCTIONS condition.
  • Page 9 Fig.3 3. Felling back cut 5. Bucking a log Fig.3 Make the felling back cut (Y) at least 50 mm Bucking is cutting a log into lengths. It is higher than the horizontal notching cut as important to make sure your footing is firm illustrated in Figure I.
  • Page 10 SYMBOLS Fig.6 To reduce the risk of injury, user must read instruction manual. Wear ear protection Fig.6 Wear eye protection Wear dust mask When bucking on a slope always stand on the uphill side of the log, as illustrated in Figure 7 .
  • Page 11 REAR HANDLE 2. ON/OFF SWITCH/TRIGGER 3. LOCK- OUT BUTTON OIL FILLER CAP CHAIN STOP LEVER (HAND GUARD) FRONT HANDLE GUIDE BAR CHAIN GRIPPING TEETH 10. CHAIN TENSIONING KNOB 11. CHAIN COVER 12. BAR AND CHAIN STORAGE/ TRANSPORTATION COVER 13. DRIVE SPROCKET 14.

  • Page 12: Technical Data

    TECHNICAL DATA WG304.1 WG300 WG303.1 WG304.2 Voltage 120V~60Hz Amps 14.5A Bar length 14 inch (345mm) 16 inch (385mm) 18 inch (440mm) Chain speed 10m/s 12m/s Oil tank capacity 6.76 ounces (200ml) Chain pitch 3/8 inch (9.68mm) Number of chain drive links Chain gauge 0.05 inch (1.27mm)

  • Page 13: Chain And Guide Bar Assembly

    2. Place the chain saw on a solid, level 1. Place the chain saw on any suitable flat surface. surface. 3. Use only genuine WORX chains or 2. Turn the Chain Tensioning Knob (10) those recommended for Guide Bar. clockwise until it is hand tight.

  • Page 14: Filling Oil Tank

    (See Fig. G2). fine. If there is no oil pattern, despite a full Check recent replaced chain tension about oil reservoir, contact WORX customer service every 10 minutes during operation. agent or WORX approved service agent. 1. Connect saw to extension cord. Connect CAUTION: Do not touch the ground extension cord to power supply (See Fig.
  • Page 15 and will dull the Chain. • Keep solid footing and balance at all times. 3. Use both hands to grip saw. Always use • Stand slightly to left side of saw. This keeps left hand to grip front handle and right your body from being in direct line with hand to grip rear handle.

  • Page 16: Maintenance And Storage Of Chain Saw

    start the cut from above(Y) about 1/3 of the 3. Maintain chain saw with care. diameter into the log (overbuck) and then • Never expose saw to rain or direct finish the cut (Z) from below, in order to avoid moisture.

  • Page 17: Sharpening Saw Chain

    • Saw has to be forced through the cut. LUBRICATE SPROCKET • Inadequate supply of oil to the bar and WARNING: Wear heavy duty gloves chain. when performing any maintenance Check the condition of the guide bar each time or service to this tool. Always unplug the chain is sharpened.

  • Page 18: Troubleshooting Table

    TROUBLESHOOTING TABLE The following table gives checks and actions that you can perform if your machine does not operate correctly. If these do not identify/remedy the problem, contact your service agent. WARNING: Switch off and remove plug from power source before investigating fault.

Table of Contents