Related Manuals for JEKKO SPD360CD
Summarization of Contents
1 PREFACE
1.1 General Information
Manual intended for users and maintenance technicians for safe operation.
Machine Marking and Identification
Information about the identification plate and CE marking on the machine.
1.2 Technical Specifications
Detailed technical data for different Jekko models.
1.3 Original Seals
Importance of lead sealings for machine safety and working conditions.
1.4 Operator Training
Requirement for technical training for correct machine operation.
1.5 Intended Use
Machine designed for load handling; specifies prohibited uses like lifting people.
1.6 Warranty
Details of warranty terms, exclusions, and claims procedures.
2 SAFETY INFORMATION
2.1 Rules
General operative rules for operator safety and environmental preservation.
2.2 Noise
Recommendations for hearing protection based on sound exposure levels.
2.3 Conveyance of Instructions
Procedures for transferring manual and operating instructions to new operators.
2.4 Dangerous Zones
Identification of hazardous areas near the machine and electrical safety distances.
2.5 Emergency Stop
Procedure for using and resetting the emergency stop function.
2.6 Daily Check
List of daily checks to be performed before operating the machine.
2.7 Features of the Working Area
Requirements for safe working areas, including ground slope and stability.
3 MACHINE SIGNALS AND CONTROLS
3.1 Main Switchboard
Description and function of controls on the main switchboard.
3.2 Radio Remote Control
Description of the radio remote control unit and its functions.
3.3 Main Electrical Cabinet
Overview of components within the main electrical cabinet.
4 USE OF THE MACHINE IN REGULAR WORKING CONDITIONS
4.1 Machine Starting
Procedures for starting the machine in battery and engine versions.
4.2 Handling and Stabilization of the Machine
Steps for moving and stabilizing the machine using outriggers.
4.3 Use of the Crane
Operation of the crane in local and remote control modes.
4.4 From Crane Configuration to Truck Configuration
Procedure for switching between crane and truck configurations.
4.5 Stop and Laying-up of the Machine
Steps for safely stopping and parking the machine.
4.6 Settings of the Tools Installed
How to select and set installed tools (winch, jib, etc.).
4.7 Diesel Engine 15LD440 Emergency Start
Manual procedure for starting the diesel engine in an emergency.
4.8 Emergency Procedure to Change Configuration
Steps for emergency configuration changes, requiring assistance.
9 TROUBLESHOOTING
9.1 Alarms of Battery Charger Model BC1
States and descriptions of alarms for battery charger model BC1.
9.2 Alarms of Battery Charger Model NG1
States and descriptions of alarms for battery charger model NG1.
9.3 Alarms of Battery Charger Model NG3
States and descriptions of alarms for battery charger model NG3.
9.4 Machine Alarms
List of machine alarms, their codes, and corresponding actions.
10 STANDAR OPERATOR MAINTENANCE
10.1 Ordinary Maintenance
Guidance on routine maintenance tasks that can be performed by the operator.
10.2 Battery Recharging
Instructions for safely recharging the machine's batteries.
10.3 How to Increase the Battery Lifetime
Tips and procedures to prolong the battery's service life.
10.4 General Warnings for Maintenance Activity
Essential safety precautions to follow during maintenance operations.
10.5 Extraordinary Maintenance
Information on extraordinary maintenance performed by authorized workshops.
11 SERVICING FORMS
11.1 Introduction
Importance of creating and updating a maintenance register as per regulations.
11.2 Events That Relieve the Manufacturer from Its Liability
Conditions under which the manufacturer is not responsible for issues.
11.3 Maintenance and Servicing Register
Forms prepared for recording maintenance and servicing activities.
12 ENCLOSURE
12.1 Summarizing List of Maintenance and Servicing Interventions
Template for summarizing maintenance and servicing interventions.
12.2 Detailed Forms On Servicing And Maintenance
Detailed forms for recording specific servicing and maintenance events.
12.3 Form For The Conveyance Of Information
Form for documenting the transfer of manual and operating information.
13 TOOLS
13.1 380V Feeding Kit for SPD265C+/360C+
Installation and use of the three-phase feeding kit for specific models.
13.2 380V Feeding Kit for SPD360CD
Installation and use of the three-phase feeding kit for SPD360CD.
13.3 380V Feeding Kit for SPD500CD
Installation and use of the three-phase feeding kit for SPD500CD.
13.4 Mechanical Jib (JM) SPD360
Load charts and specifications for the mechanical jib on SPD360.
13.5 Hydraulic Jib (JH) SPD500
Load charts and specifications for the hydraulic jib on SPD500.
13.6 Level Basket Connection (Only SPD360 Extra U.E.)
Connection of a level basket, with limitations for use outside the EU.
Need help?
Do you have a question about the SPD360CD and is the answer not in the manual?
Questions and answers