JEKKO SPX532 Quick Start Manual
  1. Manuals
  2. Brands
  3. JEKKO Manuals
  4. Construction Equipment
  5. SPX532
  6. Quick start manual

JEKKO SPX532 Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SPX532 – QUICKSTART GUIDE
R EVI SI ON
I SSUED BY
R EVI SI ONED BY
SPD-SERIES
AP P LI ED TO
JF-SERIES
M ODELS
SPX-JUNIOR
SPX-SENIOR
MPK-SERIES
NEW SERIE
OTHERS
SPX532
Quickstart Guide
ENRICO P.
IGOR P.
SPD265
SPD360
JF30
JF40
SPB209
SPX312
SPX527
SPX536
MPK20
MPK50
SPX532
SPX1280
SPK 60
OTHER
DATE OF R ELEASE
DATE OF R EVI SI ON
SPD500
JF365
SPX424
SPX1040
TOOLS
1
13/03/2020
13/03/2020
JF545
JF990
SPX429
SPX1275
INSTRUMENT
1

Advertisement

Table of Contents
loading

Related Manuals for JEKKO SPX532

Summary of Contents for JEKKO SPX532

  • Page 1 SPX532 – QUICKSTART GUIDE SPX532 Quickstart Guide R EVI SI ON I SSUED BY ENRICO P. DATE OF R ELEASE 13/03/2020 R EVI SI ONED BY IGOR P. DATE OF R EVI SI ON 13/03/2020 SPD-SERIES SPD265 SPD360 SPD500 AP P LI ED TO...

  • Page 2: Table Of Contents

    SPX532 – QUICKSTART GUIDE INDEX TURN ON THE POWER ....................................... 3 RELEASE THE EMERGENCY BUTTON ................................... 4 POWER UNIT SELECTION....................................5 TURN ON THE REMOTE CONTROL ..................................6 START/STOP DIESEL ENGINE (OR POWER PACK) ..............................7 CONFIRM LMI CONFIGURATION ..................................8 MODIFY LMI CONFIGURATION ...................................

  • Page 3: Turn On The Power

    SPX532 – QUICKSTART GUIDE 1. TURN ON THE POWER Go to the right side of the machine’s central frame, where the main switch is placed. RIGHT SIDE PANEL On the right side panel there are the following devices: main power switch (1);...

  • Page 4: Release The Emergency Button

    SPX532 – QUICKSTART GUIDE 2. RELEASE THE EMERGENCY BUTTON Check and release the emergency button on the right side panel of the machine. Check and release the emergency button on the remote control.

  • Page 5: Power Unit Selection

    SPX532 – QUICKSTART GUIDE 3. POWER UNIT SELECTION By rotating the Power unit switch selector (located on right side panel) it will be possible to engage the desired power unit: LITHIUM BATTERY PACK POWER PACK * DIESEL ENGINE POWER PACK *...

  • Page 6: Turn On The Remote Control

    SPX532 – QUICKSTART GUIDE 4. TURN ON THE REMOTE CONTROL Turn on the remote control key. Press once the Start button on the left side of the remote control and wait for “Loading HMI …” (about 5 sec.) When requested on the screen, press again the Start button and wait for...

  • Page 7: Start/Stop Diesel Engine (Or Power Pack)

    SPX532 – QUICKSTART GUIDE 5. START/STOP DIESEL ENGINE (OR POWER PACK) To start the diesel engine on SPX532CDH version (or the power pack electric motor), use the Engine start/stop selector on the remote control: START DIESEL ENGINE / POWER PACK...

  • Page 8: Confirm Lmi Configuration

    SPX532 – QUICKSTART GUIDE 6. CONFIRM LMI CONFIGURATION The LMI configuration page will be displayed automatically (see the picture beside). Press the button (on top of the screen to the right) to confirm the LMI configuration. IMPORTANT: Always check the congruity between the LMI configuration on the display and the real...

  • Page 9: Modify Lmi Configuration

    SPX532 – QUICKSTART GUIDE 7. MODIFY LMI CONFIGURATION Only if needed, use the Line falls selector to modify the LMI configuration and set the correct number of rope lines/falls or the hook mode: INCREASE THE ROPE LINE FALLS NUMBER PRESS ONCE TO GO BACK TO HOOK MODE IMMEDIATELY NOTE: The machine recognizes automatically the tool installed, thanks to the Plug&Play feature.
  • Page 10 JIB PARKED ON BOARD: the LMI takes in count the weight of the jib parked on the boom JIB NOT ON BOARD: the LMI doesn’t take in count the weight of the jib NOTE: On SPX532 the counterweight is not removable!

  • Page 11: Working Mode Selection

    SPX532 – QUICKSTART GUIDE 8. WORKING MODE SELECTION Turn the Working mode selector to select the desired working mode: PAY ATTENTION! TURRET ROTATION ENABLED! Pick & Carry Tracks Crane Outriggers Up & Down Machine stability (no functions available) IMPORTANT: BY ROTATING THE WORKING MODE SELECTOR THE MACHINE’S FUNCTIONS WILL BE DISABLED!
  • Page 12 SPX532 – QUICKSTART GUIDE 8.1. HOW TO SCROLL WORKING MODE’S PAGES IMPORTANT: AVOID TO ROTATE THE WORKING MODE ROTARY SWITCH TO VISUALIZE THE WORKING PAGES! YOU WILL DISABLE THE MACHINE FUNCTIONS AND IF THE CONDITIONS TO ENABLE THE WORKING MODE AGAIN ARE NOT SATISFIED, THIS CAN LEAD TO A LOCKED SITUATION! Pick&Carry page...

  • Page 13: Tracks

    SPX532 – QUICKSTART GUIDE NO ICONS = WORKING MODE NOT ENABLED 9. TRACKS Rotate the Working mode selector in position and the Tracks page will be displayed on the screen (see the picture beside). IMPORTANT: If the icons of the levers are not displayed on bottom of the screen, the working mode needs to be enabled! 9.1.
  • Page 14 SPX532 – QUICKSTART GUIDE 9.2. CONDITIONS TO ENABLE TRACKS The following conditions must be respected to enable the tracks functions: • All 4 outriggers lifted from the ground; If these conditions are not respected, • Crane must be in parking position (0°...
  • Page 15 SPX532 – QUICKSTART GUIDE 9.4. TRACKS FUNCTIONS...

  • Page 16: Outriggers Up & Down

    SPX532 – QUICKSTART GUIDE OUTRIGGERS UP & DOWN NO ICONS = WORKING MODE NOT ENABLED Rotate the Working mode selector in position and the Outriggers page will be displayed (see picture beside). IMPORTANT: If the icons of the levers are not displayed on...
  • Page 17 SPX532 – QUICKSTART GUIDE 10.2. CONDITIONS TO ENABLE OUTRIGGERS UP & DOWN The following conditions must be respected to enable the outriggers up & down functions: • Crane must be in parking position (0° or 180° ±3°); If these conditions are not respected, the •...
  • Page 18 SPX532 – QUICKSTART GUIDE 10.4. OUTRIGGERS UP & DOWN FUNCTIONS WARNING! The tracks drive and tracks extension are always enabled when the outriggers mode is enabled!
  • Page 19 SPX532 – QUICKSTART GUIDE 10.5. OUTRIGGERS OPENING ANGLES (SWING FUNCTION) Possible outriggers opening angles: 0° - 20° - 47° - 68° - 90°. All outriggers at 0° All outriggers at 20° All outriggers at 47° The machine can work with...
  • Page 20 SPX532 – QUICKSTART GUIDE 10.6. OUTRIGGERS EXTENSION Possible outriggers extension positions: 2.15m or 2.62m. The load charts are calculated according to the outriggers opening angles (swing) and extension. NOTE: When the outrigger is in retracted position, the lifting capacity will be...
  • Page 21 SPX532 – QUICKSTART GUIDE 10.7. OUTRIGGERS / TURRET INTERFERENCE Green arrow When stabilizing the machine, pay attention to the safety stickers installed on the outriggers’ cylinders. IMPORTANT: To avoid the interference between outriggers and turret, the green arrow must be into the green area!
  • Page 22 SPX532 – QUICKSTART GUIDE 10.8. SELF-LEVELING BUTTON Thanks to the biaxial planimetric sensor, the SPX532 can be stabilized automatically by holding the Self-leveling button. NOTE: The self-leveling function will operate only outriggers down maneuvers (LIFTING UP THE MACHINE). The self-leveling function stops when you release the button or when carrier’s inclination is 0°...

  • Page 23: Crane

    SPX532 – QUICKSTART GUIDE CRANE NO ICONS = WORKING MODE NOT ENABLED Rotate the Working mode selector in position and the Crane page will be displayed (see picture beside). IMPORTANT: If the icons of the levers are not displayed on...
  • Page 24 SPX532 – QUICKSTART GUIDE 11.2. CONDITIONS TO ENABLE CRANE The following conditions must be respected to enable the crane functions: All 4 outriggers on the ground; • If these conditions are not respected, the icons All 4 outriggers opening angles (swing) must be •...
  • Page 25 SPX532 – QUICKSTART GUIDE 11.4. CRANE FUNCTIONS ù WARNING! The winch functions are automatically disabled when working in hook mode!

  • Page 26: Pick & Carry

    SPX532 – QUICKSTART GUIDE PAY ATTENTION! TURRET ROTATION ENABLED! PICK & CARRY NO ICONS = WORKING MODE NOT ENABLED Rotate the Working mode selector in position and the Pick & Carry page will be displayed (see picture beside). IMPORTANT: If the icons of the levers are not displayed on...
  • Page 27 SPX532 – QUICKSTART GUIDE 12.2. CONDITIONS TO ENABLE PICK & CARRY The following conditions must be respected to enable the pick & carry functions: • All 4 outriggers lifted up from the ground If these conditions are not respected, the icons of •...
  • Page 28 SPX532 – QUICKSTART GUIDE 12.4. PICK & CARRY FUNCTIONS WARNING! The turret rotation function is enabled! The winch functions are automatically disabled when working in hook mode!
  • Page 29 SPX532 – QUICKSTART GUIDE 12.5. PICK & CARRY LIMITATIONS When the machine is operated in Pick & Carry mode: • Crane turret rotation function is enabled only if working in main boom configurations (turret rotation is automatically disabled when doing Pick & carry with JIB1000.2H configurations);...

  • Page 30: Machine Stability (No Functions Available)

    SPX532 – QUICKSTART GUIDE MACHINE STABILITY (NO FUNCTIONS AVAILABLE) Rotate the Working mode selector in position and the screen beside will be displayed. In this page the operator can check the machine stability (extension and swing rotation angles of outriggers).
  • Page 31 SPX532 – QUICKSTART GUIDE 13.2. MACHINE STABILITY SCREEN APPEREANCE Previous Settings Warning & LMI config Engine page page alarms page page page ACTUAL LOAD CHART OUTRIGGER 4 EXTENSION CRANE TURRET ROTATION ANGLE OUTRIGGER 4 SWING ANGLE ROTATION ANGLE LIMITS OF...

  • Page 32: Engine Power Mode Selector

    SPX532 – QUICKSTART GUIDE ENGINE POWER MODE SELECTOR The operator can select the engine power mode by rotating the Engine power mode selector on the remote control: the power modes adjust the working pressure (force), the oil displacement (speed) ��...

  • Page 33: Winch Speed Reduction Selector

    SPX532 – QUICKSTART GUIDE WINCH SPEED REDUCTION SELECTOR The operator can regulate gradually the winch speed by using the Winch speed reduction selector: the speed can be adjusted even while operating the function itself. Increase winch Reduce winch 15.1. SPEED INDICATOR The color of the icons (on the bottom of the display) will indicate the speed of the winch.

  • Page 34: Crane Speed Reduction Selector

    SPX532 – QUICKSTART GUIDE CRANE SPEED REDUCTION SELECTOR The operator can regulate gradually the speed of all crane functions (winch included) by pushing up or down the Crane speed reduction selector: the speed can be adjusted even while operating the functions.

  • Page 35: Alarms & Warnings

    SPX532 – QUICKSTART GUIDE ALARMS & WARNINGS If any alarm or warning is active, the code will be displayed on top of the screen. When there are more alarms or warnings active, the codes will roll (see the picture below).
  • Page 36 By cleaning the alarms pushing Button 6, only the active alarms will remain written in the alarm list. For further details, please check the “SPX532 WARNING AND ALARM CHART”. Push the Button 2 (on top of the display) to open the Warning page (see page 37).
  • Page 37 SPX532 – QUICKSTART GUIDE NOTE: The warning page has got the red symbol! 17.2. WARNING PAGE In the Warning page, the warnings are listed with a brief description that helps to understand the possible causes. IMPORTANT: The warning code is displayed only while the...
  • Page 38 SPX532 – QUICKSTART GUIDE 17.3. WARNING “BLOCK BY MACHINE NOT ENABLED” Working mode selector Warning code: ID:1 FMI:0 SPN:1 Description: Block by machine not enabled Effect: The working mode selected cannot be enabled (working mode selector) Suggestions: 1) Verify that all the conditions to enable the working mode selected are fulfilled!
  • Page 39 SPX532 – QUICKSTART GUIDE...

Table of Contents