Download Print this page

Hochiki HCP-1008E Installation And Operation Manual

Microprocessor based - fire alarm control panel

Hide thumbs

Table Of Contents

Table of Contents

Table of Contents
Introduction
Overall Features
Controls and Indicators
General Notes
System Components
Chassis Types
Series 1000 Fire Alarm Control Panel - Kits
MECHANICAL INSTALLATION and DIMENSIONS
Fig.1: HBB-1024 Flush or Surface Enclosure Installation and Dimensions
Fig.1A: HBB-1072 Flush or Surface Enclosure Installation and Dimensions
Main Chassis Installation
Fig.2: Main Chassis Installation
Main & Expander Chassis Installation
Fig.3: Expander Chassis Installation
Modules Mounting Locations
Fig.4: Module Mounting Locations
Fig.4A: Circuit Adder Module Mounting Details
Module Settings
MAIN FIRE ALARM MODULE (Part of Main Chassis)
Fig.5: M Ain F Ire Alarm M Odule
MAIN DISPLAY MODULE (Part of Main Chassis)
Fig.6: Main Display Module (HM CC1024-6, HMC C1024-12)
Fig.6A: Main Display Module (HM CC1024-6S, HMC C1024-12S)
ADDER DISPLAY MODULE (Part of Expander Chassis)
Fig.7: Add er D Ispla y M Od Ule
DETECTION ADDER MODULE (Model HDM-1008A)
SIGNAL ADDER MODULE (Model HSGM-1004A)
Fig.8: de Tection Add er M Od Ule
Fig.9: Signal Add er M Od Ule
RELAY ADDER MODULE (Model HRM-1008A)
POLARITY REVERSAL and CITY TIE MODULE (MODEL: HPR-100)
Fig.10: Re Lay Adder M Od Ule
Fig.11: HU DAC T-100 Dig Ital Com Mun Icato R M Od Ule
Fig.12: City Tie M Od Ule
Field Wiring
Main Fire Alarm Module Terminal Connections
Fig.13: Main Fire Alarm Module Terminal Connections
Fig.14: Main Fire Alarm Module Terminal Connections (Continued)
Detection Module (Hdm-1008A) Terminal Connections
Fig.15: Detection Module Terminal Connections
Signal Module (Hsgm-1004A) Terminal Connections
Fig.16: Signal Module Terminal Connections
Relay Module (Hrm-1008A) Terminal Connections
Fig.17: Relay Module Terminal Connections
Hudact-100 Main Board Terminal Connections
Fig.17A:hudact-100 Terminal Connection
POLARITY REVERSAL and CITY TIE MODULE (MODEL: HPR-100) TERMINAL CONNECTIONS
Fig.18: Polarity Reversal and City Tie Module Terminal Connections
Fig.19: Power Supply Connections
Wiring Tables & Information
Fig.20: WIRING TABLE for INITIATING CIRCUITS
Fig.21: WIRING TABLE for INDICATING CIRCUITS
System Checkout
Before Turning the Power "On
Power-Up Procedure
Troubleshooting
Indicators, Controls, & Operation
Fig.22: Indicators and Control Location
Common Indicators
Common Controls
Circuit Status Indicators
Circuit (Zone) Disconnect Switches
Single Stage Operation
Two Stage Operation
Circuit Types
System Configuration
Introduction to Configuration
Fig.23: Co Nfig Uration Indicato Rs an D C on Trols
Entering Configuration Mode
Exiting Configuration Mode
Factory Default Configuration
RESTORE to DEFAULT / RESIZE (CLASS a or B)
Resize System (Set Circuit Adder Module Number & Type)
Configuring Features
Configuring Initiating and Indicating Circuits
Configuring Circuit Correlations
Display Configuration
Walk Test Operation
Appendix "A" - Compatible Devices
Appendix "B" - Hra-1000 Remote Annunciator Panels
APPENDIX "C" - MODULE SPECIFICATIONS and FEATURES
Appendix "D" - Power Supply & Battery Calculations (Selection Guide)

Quick Links

1 Table of Contents
Download this manual

HCP 1000 SERIES

Microprocessor Based - Fire Alarm Control Panel

INSTALLATION and OPERATION MANUAL

NOTICE

All information, documentation, and specifications contained in this manual are subject to

change without prior notice by the manufacturer.

Printed September 6, 2000

LT-600HOC Rev.4 (Operating Instruction is NP-739HOC Rev.3)

firealarmresources.com

Table of Contents

Need help?

Do you have a question about the HCP-1008E and is the answer not in the manual?

Hochiki HCP-1008E Installation And Operation Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Hochiki HCP-1008E

Table of Contents