Russound SRC2 User Manual

Press LAST once to recall the last channel;
page back one screen in the main menu.
SRC2
Select and save favorite presets.
ADVANCED LEARNING &
Directly enter channels (e.g.,
PRE-PROGRAMMED REMOTE CONTROL
09 or 31). Press OK to send
channel number entries on
some TV models.
INSTALLING BATTERIES
1. On the back of the SRC2, push the tab and lift off
the battery cover.
2. Obtain two (2) fully-charged AA alkaline bat-
teries. Match the + and – marks on the batter-
ies to the + and – marks in the battery case,
then insert the new batteries.
3. Press the battery cover back into place. The tab
should click when the cover is locked.
USER GUIDE
4. Test the unit by pressing Power and any mode
key. If the batteries are inserted correctly, the
INTRODUCTION
LED will blink once.
The SRC2 Remote Control is the complete solution for all of
PROGRAMMING A DEVICE
your remote control requirements. It is designed to operate
source devices and Russound audio system keypads. The
To control Universal TV,VCR or DVD, Cable or
SRC2 controls up to eight devices. For best results, please
Satellite Receivers,Amplifier or tuner, and Auxiliary
read and follow all the remaining instructions and keep this
devices, follow these steps.
guide for future reference.
Before proceeding, find the codes for the devices you
want to program in "Manufacturer's Codes" in this
FEATURES AND FUNCTIONS
manual.
NOTE: key functions may vary from device to
1. Turn on the device (e.g., DVD player) and if
device. The following Key Chart provides a general needed, load media.
description of functions.
2. Press a device key.
3. Press and hold SET until the red LED blinks
Select a local device. twice, then release.
4. Enter the first five-digit code for your device.
Activates control of Russound
The LED blinks once as each digit is entered. If the
system controller and keypads,
code is correct, the LED blinks twice.
and its connected sources.
Note: If the LED does not blink twice, repeat step 4
Use these keys to
and try entering the code again.
select specific
5. Aim the remote at the device and press
sources.
POWER. The device should turn off. If it does not,
repeat steps 3-5, trying each code for your brand
until you find one that works. If you cannot find a
code that works see "Searching for Your Code" in this
Turn the selected device on or off.
manual.
6. Repeat steps 1-5 for the other devices you
Program sequences.
want to control. For future reference, write down
each working device code.
Select next/previous.
Select the next/previous chapter on some SEARCHING FOR YOUR CODE
models of DVD players.
If your device does not respond to the remote after
Press LAST to recall the last-viewed
channel. trying all codes listed for our brand, or if your brand
is not listed, try searching for your code:
Raise or lower the sound level.
1. Press a device key once.
2. Press and hold SET until the red LED blinks
twice, then release.
3. Enter 9-9-1, then the device group number
Press MUTE to turn the sound off or on. (see below). The LED blinks twice.
0 Cable (Cable Converters,
Video Accessories, Satellite
Receivers)
Move the cursor in the menu screens.
1 TV (TVs)
Press OK to choose the high
2 VCR (VCRs, DVD players)
lighted menu option. May perform "Enter"
3 Audio (Audio Amplifiers,
function for devices.
Audio Amp/Tuners,
CD players)
Press Enter to choose the highlighted
menu option. May perform "OK" function 4. Aim the remote at the device and press
for devices.
POWER. The remote sends IR codes from its library
Skip backward, rewind, fast to the selected device, starting with the most popu-
forward, skip forward, stop lar code first. If the device responds, go to step 6.
pause, or play tracks on disc.
5. If the device does not respond, press CH+. the
remote will try the next code. Continue until the
Use Page Up/Down with cable or
device responds. Press CH- to try the previous code.
satellite boxes. Note: May have to
6. Press SET to lock in code. To search for other
learn in these functions.
device codes, repeat steps 1-5.
View the current channel and
CHECKING THE CODES
program information.
Display the menu for the selected device.
If you have set up the remote using the procedure in
"Searching for Your Code, " you may need to find out
which five-digit code is operating your equipment.
Exit the selected device's menu, guide, or
For example, to find out which code is assigned to
program without making a menu selection.
your TV:
Display the program guide for the selected
1. Press the key to which the TV is assigned.
device.
2. Press and hold SET until the red LED blinks
Switch the TV's,VCR's, SAT's or DVD's
twice, then release.
input to view TV or video programs.
3. Enter 9 9 0. The LED blinks twice.
Direct disc selection.
4. To view the code's first digit, press 1. Count the Deleting a single learning key
LED blinks (e.g., three blinks =3), and enter the
1. Select a source
number in the appropriate device list in step 8 of
2. Press and hold SET until the LED flashes twice.
"Programming a Device. " If a code digit is 0, the
NOTE: If more than 15 seconds passes between key
LED does not blink.
presses, the remote exits programming.
5. Repeat step 4 for the remaining digits, using 2
3. Press 9 7 6.
for the second digit, and so on.
4. Press the key (twice) containing the learned
6. To check for other device codes, repeat
function to be deleted. The remote blinks twice.
steps 1-5, using the appropriate key.
5. Repeat steps 1-4 for another key on the same
CHANGING VOLUME LOCK source, or press and hold SET to exit programming.
Deleting all learned keys in a specific mode
The SRC2 remote comes preset to allow independent
1. Press and hold SET until the LED blinks twice.
volume control of each selected device (Global
Volume Unlock). However, you may change the
Note: If more than 15 seconds pass between key
Volume Lock setting to Global Volume Lock so that
presses, the remote exits programming.
one device's volume will control volume in all other
2. Press 9 7 6.
modes.After that , you can perform Individual
3. Press a device key twice to delete all the
Volume Unlock on a selected device to set its volume
learned keys for that mode. The LED blinks twice.
control for independent operation or Global Volume
4. Repeat steps 1-3 for another set of keys for a
Unlock to remove all volume locking.
device, or press and hold SET to exit programming.
Locking Volume Control to One Mode (Global Volume
TROUBLESHOOTING
Lock)
1. Press and hold SET until the red LED blinks
Problem: LED does not blink when you press a key.
twice, then release.
Solution: Replace battery with two new AA batteries.
2. Enter 9 9 3 and then press the mode key for
Problem: LED blinks when you repress a key, but
the device you want to control volume (e.g., TV).
device does not respond.
The LED blinks twice. Now when you press VOL+,
Solution: Make sure the remote is aimed at your
VOL-, or Mute, the selected device will control the device or system keypad and is not more than 15
volume regardless of the current mode. feet away.
Problem: LED blinks one long blink.
Unlocking All Volume Control (Restoring Global Unlock)
Solution: An entry error has occurred (e.g., wrong
1. Press and hold SET until the red LED blinks
key). Try entry sequence again.
twice, then release.
Problem: Remote does not control devices or com-
2. Enter 9 9 3 and then press VOL+. The LED
mands are not working properly.
blinks four times.Volume is independently con-
Solutions: Try all listed codes for the device. Make
trolled for all programmed devices. sure the device operates with an infrared remote
control.
Unlocking a Single Device's Volume Control
Problem: CH+, CH- and LAST do not work for your
1. Press a device key (VID, DVD, etc.).
RCA TV.
2. Press and hold SET until the red LED blinks
Solution: Due to RCA design from 1983 to 1987, only
twice, then release.
the original remote control will operate these func-
3. Enter 9 9 3 and then press VOL-. The LED tion.
Problem: Channels do not change properly.
blinks four times.Volume is independently con-
trolled for the selected devices. Solution: If the original remote control required you
to press ENTER to change channels., press enter on
USING LEARNING
this remote after entering the channel number.
ADDITIONAL INFORMATION
The SRC2 includes a Learning feature so you can
add functions that are unique to your home enter-
The SRC2 does not have any user-serviceable
tainment devices (e.g.,VCR Tracking Up or Down).
parts. Opening the case, except for the battery
The following precautions apply.
cover, may cause permanent damage to the
• The original remote controls must be in working
SRC2.
order for learning to work properly.
• Learned keys are mode specific, so each one can
Copyright ©2005 Russound, Inc.
store a unique function for each mode.
Russound, 5 Forbes Road,
• Do not use the following keys for learning: Device
Newmarket, NH 03857
Keys, SET, Back, or Record.
603.659-5170 www.russound.com
• Learning capacity is approximately 40 to 100 keys,
depending on the code being learned.
28-1206 REV. 1 11/30/05
• Certain device codes are not learnable including
multi-frequency types, some high frequency ones,
and other unusual formats.
• For optimum learning, avoid high levels of ambient
light such as natural sunlight or energy-efficient flu-
MANUFACTURER'S CODES
orescent lights.
• Have the original remote controls handy before
Setup Codes for Audio Amplifiers
programming learning.
Bose 30674
Programming a learned key
GE 30078
Note: If more than 15 seconds pass between key
JVC 30331
presses, the remote exits programming.
Marantz 30321
1. Press and hold SET until LED flashes twice. Nakamichi 30321
NEC 30264
2. Press 9 7 5.
Optimus 30395
3. Press a device key once to assign a mode for learning.
Realistic 30395
4. Place the SRC2 head-to-head (about 2" apart)
Sansui 30321
from your original remote control.Also locate the
Shure 30264
key (on original remote control) that will serve as
Sony 30689
the teaching function. Soundesign 30078
Victor 30331
5. On the SRC2, press a key where the learned
Wards 30078
function will be stored.
Yamaha 30354, 30133
6. On the original remote, press and hold the the
key to be learned. The SRC2 LED will turn off.
Continue holding the key on the original remote
until the SRC2 LED blinks twice.
Note: If the LED displays one long blink, a learning
Setup Codes for Audio Amp/Tuners
error has occurred. Try repeating this step again
ADC 30531
until a successful capture occurs. If the function is
Aiwa 31405, 31243, 30121
still not captured, press and hold SET to exit pro-
Anam 31609, 31074
gramming. Review the learning precautions listed
Audiotronic 31189
above, or the Troubleshooting tips below, before
Bose 31229
beginning again at step 1.
Capetronic 30531
7. Repeat steps 4-6 for another key on same
Carver 31189
device, or repeat steps 1-6 for another device.
Coby 31263
Denon 31360, 31142, 30904
Fonmix 31360 Denon 30873
Glory Horse 31263 DKK 30000
Harman/Kardon 30110 DMX Electronics 30157
Hitachi 31273 Dynamic Bass 30179
Inkel 30027 Fisher 30179
Integra 30135 Garrard 30420
JBL 30110 Genexxa 30032
JVC 30074, 31263 Harman/Kardon 30157, 30173
Kenwood 31313, 31570, 30027 Hitachi 30032
KLH 31428 Integra 30101
Magnavox 31189, 31269, 30531 JVC 30072
Marantz 31189, 31269, 30039 Kenwood 30826, 30626, 30028, 30037, 30036,
30190
MCS 30039
Krell 30157
Onkyo 30842, 30135
Linn 30157
Optimus 31023, 30670, 30531, 31074
Panasonic 31518, 30039 Magnavox 30157
Marantz 30626, 30029, 30157
Philips 31189, 31269
MCS 30029
Pioneer 31023, 30150, 30014, 30630, 30531
Miro 30000
Proscan 31254
Mission 30157
Qisheng 31609
MTC 30420
Quasar 30039
RadioShack 31263 NSM 30157
Onkyo 30868, 30101
RCA 31023, 31609, 31254, 30531, 31074
Optimus 31063, 30000, 30032, 30037, 30420,
Sharper Image 31263
30179, 31075, 30145
Silsonic 30176
Panasonic 30029
Sony 31058, 31441, 31258, 31759
Parasound 30420
Soundesign 30670
Philips 30626, 30157
Stereophonics 31023
Pioneer 31063, 31062, 30032
Sunfire 31313
Polk Audio 30157
Teac 31074, 31267
Proton 30157
Technics 31308, 31518, 30039
QED 30157
Thorens 31189
Quad 30157
Victor 30074
Quasar 30029
Wards 30014
RadioShack 31075
Yamaha 30176, 31276, 31176
RCA 31062, 30032, 30420, 30179, 30053
Realistic 30420, 30179
Rotel 30157, 30420
SAE 30157
Sansui 30157
Setup Codes for Cable Converters
Sanyo 30179
SAST 30157
ABC 00003, 00008, 00014
Sharp 30861, 30037
Americast 00899
Silsonic 30888, 30036
Bell & Howell 00014
Sonic Frontiers 30157
Bell South 00899
Sony 30490, 30000, 30100
Clearmaster 00883
Soundesign 30145
ClearMax 00883
TAG McLaren 30157
Coolmax 00883
Tascam 30420
Daeryung 01877, 00877, 00477, 00008
Teac 30420
Digi 00637
Technics 30029
Director 00476
Victor 30072
Dumont 00637
Wards 30157, 30053
Gehua 00476
Yamaha 30888, 30036
General Instrument00476, 00810, 00276, 00003, 00014
Zonda 30157
GoldStar 00144
Hamli 00009, 00273
Hitachi 00014
Jerrold 00476, 00810, 00276, 00003, 00012,
00014
KNC 00008
Setup Codes for DVD Players
LG 00144
Aiwa 20641, 21912
Memorex 00000
Akai 20770
Motorola 00476, 00810, 00276, 01254, 01376
Allegro 20869
MultiVision 00012
Pace 01877, 00237 Apex Digital 20672, 20717, 20797, 21061, 20796,
21056, 21937, 20794, 21020, 21915
Panasonic 00000, 00008, 00107
Blaupunkt 20717
Panther 00637
Blue Parade 20571
Paragon 00000
Broksonic 20695
Philips 00317, 01305
Changhong 20627, 21061
Pioneer 01877, 00877, 00144, 00533
CineVision 20869
Pulsar 00000
Coby 21086
Quasar 00000
Curtis Mathes 21087
RadioShack 00883
CyberHome 21024, 21023, 21129, 20816, 21117
Regal 00279, 00273
Daewoo 20833, 21172, 20869
Runco 00000
Denon 20490
Samsung 00000, 00144
DVD2000 20521
Scientific Atlanta 01877, 00877, 00477, 00008
Emerson 20591, 20675
Sony 01006
Enterprise 20591
Starcom 00003, 00014
Fisher 21919
Supercable 00276
Funai 20675
Supermax 00883
Gateway 21158, 21073
Tocom 00012
GE 20522, 20717
Torx 00003
Go Video 20744, 20833, 21099, 20783, 21075,
Toshiba 00000
20869, 21730
Trans PX 00276
Greenhill 20717
Tristar 00883
Harman/Kardon 20582, 20702
TS 00003
Hitachi 20573, 20664, 21919
V2 00883
Hiteker 20672
Viewmaster 00883
Initial 20717
Vision 00883
Integra 20627, 21924
Vortex View 00883
JBL 20702
Zenith 00000, 00525, 00899
JVC 20558, 20623, 20867
Kenwood 20490, 20534
KLH 20717, 21020, 21149
Koss 20651, 21980
Lasonic 20798
Setup Codes for CD Players
LG 20591, 20869, 20801
Liquid Video 21980
Aiwa 30157
Lite-On 21158, 21058
Burmester 30420
Loewe 20511
California Audio Labs30029
Magnavox 20503, 20539, 21976, 21914, 20675
Carver 30157, 30179
Marantz 20539 Setup Codes for TVs
Memorex 20695
Addison 10092
Microsoft 20522
Admiral 10093, 10463
Mintek 20717
Advent 10761, 10842
Mitsubishi 21521, 20521
Aiko 10092
Nesa 20717
Aiwa 11914
Norcent 21003
Akai 10812, 10702, 10030, 10672, 11903
Onkyo 20503, 20627, 21924, 20792
Albatron 10700, 10843
Oritron 20651, 21980
America Action 10180
Panasonic 20490, 21762, 21990
Anam 10250, 10180, 10700
Philips 20503, 20539, 20646, 21914
Anam National 10250, 10650
Pioneer 20525, 20571
Anhua1 0051
Polaroid 21086, 21061
AOC 10451, 10093, 10180, 10060, 10030,
Polk Audio 20539
10178, 10092
Portland 20770
Apex Digital 10748, 10765, 10879, 10767, 11943
Proscan 20522
Audiovox 10451, 10180, 10875, 10092, 10623
Qwestar 20651
Baile 10661
RCA 20522, 20571, 20717, 20822
Beijing 10812, 10661
Rio 20869
Bell & Howell 10154
Rotel 20623
BenQ 11032
Sampo 20752, 20698
Bradford 10180
Samsung 20490, 20573, 21932, 21075, 20820
Broksonic 10236, 10463, 11911, 11938, 11905,
Sansui 20695
11935, 11929
Sanyo 20695
Cailing 10748
Sharp 20630, 20752
Candle 10030
Sharper Image 21117
Carnivale 10030
Sherwood 20770
Carver 10054
Shinco 20717
Celebrity 10000
Shinsonic 20533
Celera 10765
Sonic Blue 20869, 21099
Changcheng 10051, 10661
Sony 20533, 20864, 21033, 21904, 21903
Changhong 10156, 10765, 11156, 10767
SVA 20717
Ching Tai 10092
Sylvania 20675
Chun Yun 10000, 10180, 10700, 10092, 10843
Symphonic 20675
Chung Hsin 10180, 10053
Teac 20717, 21984, 20809
Cinema 10672
Technics 20490
Citizen 10060, 10030, 11928, 10092
Theta Digital 20571
Clarion 10180
Toshiba 20503, 20695
Commercial Solutions11447, 10047
Urban Concepts 20503
Conrowa 10156, 10145, 11156
Xbox 20522
Contec 10180
Yamaha 20490, 20539, 20545
Craig 10180
Zenith 20503, 20591, 20869
Crosley 10054
Crown 10180
Curtis Mathes 10047, 10054, 10154, 10451, 10093,
10060, 10702, 10030, 10145, 10166
CXC 10180
Daewoo 10154, 10451, 10180, 10030, 10178,
Setup Codes for Satellite Receivers
10672, 11928, 10092, 10661, 11909,
AlphaStar 00772 10623, 10700
Chaparral 00216 Dayu 10661
Dell 11080
Crossdigital 01109
Denon 10145
DirecTV 00392, 00566, 00639, 01142, 00247,
00749, 01749, 00724, 00819, 01856, Dumont 10017
01076, 01109, 00099, 01392, 01640,
Durabrand 10463, 10180, 10178, 10171, 11034
01442, 01414, 01108
Electroband 10000
Dish Network System 01005, 00775, 01505
Emerson 10154, 10236, 10463, 10180, 10178,
Dishpro 01005, 00775, 01505
10171, 11944, 11909, 11929, 11905,
Echostar 01005, 00775, 01505
11928, 10623, 11911
Expressvu 00775 Envision 10030
GE 00566 Ether 10030
General Instrument 00869 Firstar 10236
GOI 00775
Fisher 10154
Goodmans 01246
Fortress 10093
Hisense 01535
Fujitsu 10809, 10853
Hitachi 00819, 00222, 01250 Funai 10180, 10171, 11904
HTS 00775 Furi 10145
Hughes Network Systems 01142, 00749, 01749, 01442 Futuretech 10180
I-Lo 01535
Gateway 11756, 11755
JVC 00775
GE 11447, 10047, 11454, 10051, 10451,
LG 01414, 01226 10180, 10030, 10178, 11917, 10092,
11907, 11922
Magnavox 00724, 00722
Gibralter 10017, 10030
Memorex 00724
GoldStar 10154, 10030, 10178, 11926
Mitsubishi 00749
Grunpy 10180
Motorola 00869
Haier 11034
NEC 01270
Hallmark 10178
Next Level 00869
Hankook 10180, 10030, 10178
Panasonic 00247, 00701
Harley Davidson 11904
Paysat 00724
Harman/Kardon 10054
Philips 01142, 00749, 01749, 00724, 01076,
Harvard 10180
00722, 00099, 01442
Proscan 00392, 00566 Havermy 10093
Proton 01535 Helios 10865
RadioShack 00869 Hello Kitty 10451
RCA 00392, 00566, 00855, 00143, 01392 Hisense 10156, 10748, 10145, 11156
Hitachi 10156, 10030, 10178, 11145, 10145,
Samsung 01276, 01109, 01108
10092, 11904, 11156
Sanyo 01219
Hongmei 10093
SKY 00856
Huafa 10145
Sony 00639, 01640
Huari 10145
Star Choice 00869
Huodateji 10051
Tivo 01142, 01442
Imperial Crown 10661
Toshiba 00749, 01749, 00790, 01285
Infinity 10054
UltimateTV 01640, 01392
Inteq 10017
Uniden 00724, 00722
JBL 10054
US Digital 01535
JCB 10000
USDTV 01535
Jean 10156, 10051, 10236, 10092
Voom 00869
Jensen 10761
Zenith 00856, 01856
Jiahua 10051
Jinfeng 10051
Jinxing 10054, 10156, 10145
JVC 10053, 11923, 11253
Kangli 10661