Related Manuals for Tume CultiPlus 4000
Summary of Contents for Tume CultiPlus 4000
- Page 1 No: B-98812304 4/2020 USER MANUAL CultiPlus 3000 CultiPlus 4000 Starting from serial JF-1778 All rights to structural changes reserved Read the manual before operating the machine Translation...
- Page 3 Name and address of person authorized to compile a technical file: Name: Heimo Valli Address: Sudenkorventie 1, FI-14200 Turenki Hereby declares that Cultivators TUME CultiPlus 3000 and 4000 Serial number ___________________ • are in compliance with the applicable decrees of the Machine Directive (2006/42/EC) and in addition declares, that •...
-
Page 4: Table Of Contents
CONTENT Basic adjustment ....................8 Tine cultivator adjustments ................10 Disc cultivator adjustments ................11 Rear wheel packer adjustment ................13 6.1 Additional weights ....................13 6.2 Front support wheels .................... 14 7.1 Tine cultivator section ................... 14 7.2 Disc cultivator section ................... 14... - Page 5 CultiPlus is intended to use with Tume CultiPack disc cultivator. Only CultiPack can be used with seed drill. If extra weights are needed, the only approved way is to add weight plates inside the cultivator’s front beam.
- Page 6 2. HYBRID CULTIVATOR TUME CULTIPLUS CultiPlus is a trailed cultivator connected to the tractors towing hitch. The first cultivating section has two rows of tines, the second section has two rows of discs and lastly a wheel packer which works also as transport wheels (picture 1).
- Page 7 4. CONNECTING THE CULTIVATOR TO TRACTOR AND TRANSPORT Tume CultiPulus is a trailed machine. Drawbar is equipped with a hydraulic cylinder which is used to lift the cultivator from work position to transport position together with the cylinder on top of the machine.
-
Page 8: Basic Adjustment
DANGER! Lower the machine always to the ground before service and always when you leave the machine unattended. Pay attention to the installation and attachment of the hydraulic hoses and electric cables. Hoses and cables must be secured so that they cannot be pinched, stretched or caught in other structures. The trajectories should be ensured in practice, by running the cultivator carefully to so steep turn as it can go in work. - Page 9 CultiPlus bracket holes A, B or C for the pin. Pin position: 1 – Long pin down. 2 – Long pin up. Picture 3. Default setting. Picture 4. Working depth table. Working depth with different basic settings. (First the pin hole, second the pin direction, compare to picture 4) A1 –...
-
Page 10: Tine Cultivator Adjustments
5.2 Tine cultivator adjustments The angle of the tines can be adjusted between three positions (picture 6). • • Stone release sensitivity is adjusted by loosening / tightening the spring (picture 7). Tine angle positions, 3 options. Picture 6. Tine angle adjustment. Stone release sensitivity. -
Page 11: Disc Cultivator Adjustments
5.3 Disc cultivator adjustments When tine cultivator’s working depth is adjusted, the disc cultivator working depth is adjusted • by limiting the cylinder movement (picture 8) which determines the working angle of the cultivating elements. The rigging screws between the disc rows are set to right position in the factory and usually those are not needed to be adjusted. - Page 12 Picture 9. Electric switch for selecting only disc cultivator working depth adjustment during work. Picture 10. Side leveller, right. Picture 11. Side leveller, left. Picture 12. Lateral adjustment for the front disc row.
-
Page 13: Rear Wheel Packer Adjustment
5.4 Rear wheel packer adjustment Wheel packer turning must always be locked in CultiPlus use, so when disc and tine • cultivators connected together (picture 13). When only CultiPack (disc cultivator part) is connected to the tractor three point linkage, •... -
Page 14: Front Support Wheels
6.2 Front support wheels The front support wheels can be used to maintain the working depth better, especially in 4-meter models (picture. 15). Picture 15. Front support wheels. 7. SERVICE AND STORAGE 7.1 Tine cultivator section Grease stone protection joints, drawbar, drawbar cylinder and lifting cylinder sleeves every 50 hours. Replace worn tip and wing parts on the cultivator tines. - Page 15 8. TECHNICAL DATA MODEL CultiPlus 3000 Length, m 300 cm 400 cm Transport width, cm 300 cm 400 cm Total weight, kg 2400 kg 3050 kg Power requirement, hp 120-150 hp 150-200 hp Working depth, tine cultivator, mm 50-170 mm...
- Page 16 TUME-AGRI OY PL 77 14200 TURENKI FINLAND TEL. (int.) 358-207 433 060 www.tumeagri.fi/site/en...
Need help?
Do you have a question about the CultiPlus 4000 and is the answer not in the manual?
Questions and answers