Related Manuals for Haier HHN1230DBBB
Summary of Contents for Haier HHN1230DBBB
-
Page 1: Range Hood
Range Hood Extractor de Aire Hotte de Cuisinière User Manual Model 1000/2000 Series Guide de l’Utilisateur 1000/2000 Series Manual del Usuario Modelo 1000/2000 Series... -
Page 2: Safety Precautions
English SAFETY PRECAUTIONS WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact our customer service department for assistance. Our Toll-Free number is 1-877-337-3639. - Page 3 4. Please read specification label on product for further information and requirements. SAVE THESE INSTRUCTIONS for Future Use Thank you for using our Haier product. This easy-to-use manual will guide you Model number in getting the best performance from your Haier Range Hood.
-
Page 4: Table Of Contents
English Table Of Contents PAGE Safety Precautions..................1-2 Accessories ....................3 Installation Preparation ................4 Preparing Hood Location ................4 Preparing Hood ..................5-7 Preparing Electrical Connections..............8 Installing Hood ..................9 Operating the Range Hood..............10-11 Use and Care..................12 Troubleshooting ..................13 Warranty Information ................14 Accessories Range Hood Accessories Provided: 1 Range Hood 1 7”... -
Page 5: Installation Preparation
English Installation Preparation To install this range hood, you will need the following tools and materials: Note: This procedure will require 2 people for easier installation. Tools Needed for Installation Drill 1/8” Drill bit for drilling pilot holes 1-1/4” Wood bit for drilling electrical wiring access hole Phillips head screwdriver Flat-head screwdriver Pliers... -
Page 6: Preparing Hood
English Preparing Hood 1. (Skip to step 2 if you have 1000 series model.) Remove 7” Round Duct Plate and 3¼” x 10“ Damper from inside of the hood. Set duct plate and damper aside - with mounting screws. 7” Round Duct Plate 3¼”... - Page 7 English 4. Remove the appropriate electrical knockout by inserting a screwdriver. Then snip or break the attachment points. 5. Remove either top or back wiring knockout and install approved electrical conduit according to national electrical code. Non-Ducted Installation - Skip to “Preparing Electrical Connections” section.
- Page 8 English Insert the vent cover into the slot on the front of the range hood. 8. Fasten the vent cover with 2 screws supplied. (2) #8 Screws 9. Remove appropriate Duct Knockout(s) from top or back of hood. TOP RECTANGULAR DUCT KNOCKOUT (Remove for 3¼”...
-
Page 9: Preparing Electrical Connections
English Preparing Electrical Connections WARNING: To reduce the risk of electric shock, make sure power is switched off at the service panel. Lock or tag service panel to prevent power from being switched on accidentally. 1. Connect House Wiring (120 VAC) to hood. Use a piece of Cardboard to protect the cooktop, if necessary. -
Page 10: Installing Hood
English Installing Hood 1. Hang hood from (4) Mounting Screws (from parts bag). Be sure to place a washer (included) onto each screw before driving in the screw. Slide hood towards wall until mounting screws are engaged in narrow end of (4) Keyholes. -
Page 11: Operating The Range Hood
Fan Speed Settings Your new Haier range hood comes equipped with 3 different fan speeds: “low”, “med”, or “high”. To turn on the fan, simply turn the knob selector to the position corresponding to the desired fan speed. - Page 12 To turn off the light, put the switch back in the original position. Fan Speed Settings Your new Haier range hood comes equipped with 2 different fan speeds: “low” or “high”. To turn on the fan, simply press the switch to place in position of the desired fan speed.
-
Page 13: Use And Care
Warning! Disconnect range hood from the electrical power supply before servicing. All parts may be obtained from service centers authorized by Haier, or may be ordered directly from Haier. When ordering parts, please specify the range hood model number on the rating label, which is located on the inside of the range... -
Page 14: Troubleshooting
English Troubleshooting Fan does not turn on, but light turns on. This is probably due to either a defective fan switch or a burned-out fan motor. Fan only runs at one speed. Please see instructions above for troubleshooting when your fan does not turn on, but lights turn on. -
Page 15: Warranty Information
What will be done? and for installation of a replacement part, beyond the initial 12-month period. Haier will repair or replace, in your home, any mechanical or electrical part which proves THIS LIMITED WARRANTY IS GIVEN IN LIEU defective in normal household use for a period OF ALL OTHER WARRANTIES, EXPRESSED of 12 months. - Page 16 NECESITA UNA PRUEBA DE COMPRA FECHADA PARA EL SERVICIO DE LA GARANTIA 110-120V~60Hz Made in China Fabriqué en Chine Hecho en China Haier New York, NY 10018 Printed in China 1000/2000 Series ©2011 Haier America Trading, LLC. All Rights Reserved.