Table of Contents
Advertisement
<
CONTENTS
CONTENTS (ENGLISH)
1
INTRODUCTION
2
UNPACKING
3
M1 MAINS CONNECTION
4
SAFETY FIRST
4.1 Tripod mounting
4.2 Stacking
4.3 Rigging and suspension
5
M1 CONNECTIONS
6
M1 OPERATION
7
ICT300 COMPACT LOUDSPEAKER
8
AMPLIFIER POWER
8.1 Connecting to an amplifier
8.2 Cable lengths
9
WARRANTY
10
TECHNICAL SPECIFICATIONS
>
PRINT
The Martin Experience
Martin Audio – M1 and ICT300
MARTIN AUDIO
L O N D O N
GUIDES
Page No
2
2
3
3
4
4
4
5
5
6
6
6
7
7
8
Advertisement
Table of Contents
Related Manuals for Martin Audio ICT300
Summary of Contents for Martin Audio ICT300
- Page 1 4.3 Rigging and suspension M1 CONNECTIONS M1 OPERATION ICT300 COMPACT LOUDSPEAKER AMPLIFIER POWER 8.1 Connecting to an amplifier 8.2 Cable lengths WARRANTY TECHNICAL SPECIFICATIONS MARTIN AUDIO L O N D O N The Martin Experience Martin Audio – M1 and ICT300...
-
Page 2: Introduction
Thank you for purchasing a Martin Audio M1 system controller and ICT300 compact loudspeaker system. The M1 is used to optimise the performance of the ICT300, whether it is used as a stand-alone system or with additional sub-bass enclosures. UNPACKING Every Martin product is built to the highest standard and thoroughly inspected before it leaves the factory. -
Page 3: Mains Connection
Hearing loss is cumulative and can result from levels above 90dB if people are exposed for a long period. Never stand close to loudspeakers driven at a high level. Martin Audio – M1 and ICT300... -
Page 4: Tripod Mounting
PRINT GUIDES Tripod mounting The ICT300 incorporates a pole mounting socket to facilitate mounting on tripod stands. When using stands, the following precautions are advised: Ensure that the stand will support the weight of the speaker by checking the stand manufacturers rating. -
Page 5: M1 Connections
Martin Audio ICT300 compact loudspeaker system used either full- range or with additional sub-bass. When using an ICT300 on its own, set the mode switch on the rear of the M1 to full-range. If additional bass enclosures are used, set the mode switch to sub-bass and drive the bass amplifiers from the sub-bass output jack. -
Page 6: Amplifier Power
When powering down the system, reverse the sequence and switch off the amplifiers first. Connecting to an amplifier The panel at the rear of the ICT300 is fitted with two Neutrik Speakon NL4 connectors wired in parallel as follows: PIN 1-... -
Page 7: Warranty
GUIDES Cable lengths When connecting an ICT300 to an amplifier, it is recommended that the return resistance of the cable used is less than one tenth of the nominal impedance of the system or systems in parallel. The table below gives an indication of the maximum permissible cable runs for various conductor cross-sectional areas driving 4 and 8 ohm loads. -
Page 8: Technical Specifications
(W) 680mm x (H) 390mm x (D) 450mm (W) 26.8ins x (H) 15.4ins x (D) 17.7ins SHIPPING WEIGHT 19kg (41.9lbs) Due to our policy of continuous product improvement all specifications are subject to change without notice. Martin Audio – M1 and ICT300... -
Page 9: Visit Our Website
< > CONTENTS PRINT GUIDES System Controller & ICT300 Compact Loudspeaker Please Click here to return to main menu Please Click here to visit our website MARTIN AUDIO L O N D O N The Martin Experience Century Point, Halifax Road, Cressex Business Park, High Wycombe, Buckinghamshire HP12 3SL, England. - Page 10 < > CONTENTS PRINT GUIDES System Controller & ICT300 Compact Loudspeaker User’s Guide ENGLISH MARTIN AUDIO L O N D O N The Martin Experience...