Advertisement
INSTALLATION & OPERATING
Clean Air Freestanding Wood Fires
1.
This Kent freestanding wood fire must be installed by an approved installer, ideally
registered with the New Zealand Home Heating Association. Do not allow any
makeshift or compromising installation methods as this could result in a house fire.
This Kent freestanding wood fire must be installed according to these instructions.
2.
A Building Consent from the Local Authority must be obtained before installing
this wood fire, and we suggest that the Insurance Company covering building
insurance be advised of the installation.
3.
This Kent freestanding wood fire, when installed according to these instructions,
complies with the provisions of AS/NZS 2918-2001 "Installation of Domestic Solid Fuel
Burning Appliances".
4.
The clearances given in these instructions are necessary to prevent overheating
of nearby combustibles and drying out of the house structure. They may not be
reduced without authorisation.
5.
Important: Read all instructions carefully before starting installation. Failure to follow
these instructions could result in a fire hazard, and may void warranty.
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Important: the installer or seller must leave these instructions with the purchaser
INSTRUCTIONS
CONTENTS
General Information ........................ 1
Specifications ................................... 2
Installation ...................................... 4-6
Operation ....................................... 6-8
Maintenance .................................... 9
Replacement Parts ................... 10-11
Warranty .......................................... 12
GENERAL INFORMATION
Advertisement
Related Manuals for KENT Murchison
Summarization of Contents
General Information
Installation and Compliance
Emphasizes professional installation, building consent, and compliance with standards.
Clearance and Safety Precautions
Highlights necessary clearances and stresses reading instructions to avoid hazards.
Specifications and Clearances
Model Specifications
Details external dimensions, average emissions, and efficiency for different models.
Recommended Flue Kits
Lists recommended flue kits and their testing compliance for Kent fires.
Minimum Installation Clearances
Provides detailed measurements for wall, corner, and hearth clearances for various models.
Flue Installation Options
Single Story Flue Kits
Illustrates single story flue installation options with corresponding flue kits.
Extra Flue Components
Lists available additional flue components and their descriptions.
Freestanding Wood Fire Installation
Installation Requirements and Preparation
Lists essential items for installation and discusses floor protection and fire securing.
Standard Flue Installation Procedure
Details the process for cutting holes, fitting casings, and joining flue pipes.
Flue Termination and Door Adjustment
Flue Termination and Stability
Explains flue height requirements, bracing for stability, and clearance from roof structures.
Door Handle and Seal Adjustment
Provides instructions for adjusting the door handle and ensuring a proper seal for efficient burning.
Environmental Factors and Operation Introduction
Environmental Factors Affecting Flue
Discusses how land topography and wind conditions affect flue performance.
House Pressure and Ventilation
Addresses negative house pressure issues and the need for adequate ventilation.
Firewood Selection and Storage
Guides on choosing seasoned dry wood and proper storage to optimize performance and safety.
Operation Guide
Lighting the Wood Fire
Step-by-step guide for safely lighting the wood fire and establishing a good burn.
Normal Operation and Air Control
Explains how to operate the fire for optimal burning, adjust air control, and reload fuel.
Operation and Maintenance Preparation
First Fire Curing
Instructions for the initial use to cure the stove paint for durability.
Ash Removal and Disposal
Details how to clean out ashes and safely dispose of them to prevent hazards.
Creosote, Rust, and Wood Quality
Advises on creosote, flue cleaning, rust, and testing wood moisture.
Maintenance Procedures
Cleaning and Lubrication
Outlines methods for cleaning the exterior, door glass, and lubricating moving parts.
Re-painting and Surface Protection
Covers touch-up painting, rust removal, and protecting steel surfaces during non-use periods.
Service and Maintenance Records
Provides a template for logging maintenance activities and dates.
Replacement Parts
Kent Air Tubes
Explains the function of air tubes and provides a guide for their replacement.
Internal Components Replacement
Kent Baffles
Details the Kent baffles, their role, and the procedure for replacement.
Kent Fire Bricks
Describes Kent fire bricks, their consumable nature, and when they need replacement.
Warranty Information
Warranty Terms and Conditions
Covers the warranty period, exclusions, installation requirements, and claim procedures.
Warranty Registration Form
A form to be completed for recording installation and purchase details for warranty claims.
Need help?
Do you have a question about the Murchison and is the answer not in the manual?
Questions and answers