Download Print this page
Simpson P27SL5 Operator's Manual
Simpson P27SL5 Operator's Manual

Simpson P27SL5 Operator's Manual

Strong-tie anchor systems

Advertisement

Quick Links

LIMITED WARRANTY (ONE YEAR)
ON SIMPSON BRAND TOOLS
Simpson warrants their tool operated under normal uses in
the United States and Canada, that Simpson will repair replace
One Year
Limited
or adjust any of these tools or their component parts found
Warranty
to be defective in materials or workmanship within one year
from the date of purchase.
All we require is that you properly operate and maintain the tool as described
herein and that you return the tool for warranty repairs to Simpson.
To the extent allowed by law:
1. Any implied warranty of merchantability or fitness is limited to the
one-year duration of this written warranty.
2. Simpson shall not have any responsibility for loss of use of these
tools, loss of time, inconvenience, commercial loss or incidental or
consequential damages.
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you.
This warranty gives you specific legal rights and you also may have other
rights, which may vary, from state to state.
Return Tools To:
Northwest USA
Southwest USA
Simpson Strong-Tie Co.
Simpson Strong-Tie Co.
5151 S. Airport Way
260 N. Palm Street
Stockton, CA 95206
Brea, CA 92821
(209) 234-7775
(714) 871-8373
Southeast USA
Eastern Canada
Simpson Strong-Tie Co.
Simpson Strong-Tie Co.
1720 Couch Drive
5 Kenview Boulevard
McKinney, TX 75069
Brampton, Canada L6T 5G5
(972) 542-0326
(905) 458-5538
Northeast USA
Simpson Strong-Tie Co.
2600 International Street
Columbus, OH 43228
(614) 876-8060
Western Canada
Simpson Strong-Tie Co.
11476 Kingston Street
Maple Ridge, B.C. Canada V2X-0Y5
(604) 465-0296
Form T-SAS-PTP2704 4/04
Read This Manual
BEFORE Operating This Tool
OPERATOR'S MANUAL
Model PTP-27
4120 Dublin Blvd., Suite 400, Dublin, CA. 94568 • www.simpsonanchors.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the P27SL5 and is the answer not in the manual?

Questions and answers

Summary of Contents for Simpson P27SL5

  • Page 1 1. Any implied warranty of merchantability or fitness is limited to the OPERATOR'S MANUAL one-year duration of this written warranty. 2. Simpson shall not have any responsibility for loss of use of these Model PTP-27 tools, loss of time, inconvenience, commercial loss or incidental or consequential damages.
  • Page 2 Reassemble the parts in reverse order than you have disassembled them. ¬ Serious Injury Or Death May Result If This Tool Is Not Used In Notice the proper selection of the PTP-27 equipment according to sort of fasteners. Accordance To This Instructions! TROUBLESHOOTING...
  • Page 3 3. Take off the shear clip. INTRODUCTION The Simpson Strong-Tie PTP-27 tool is a low velocity or indirect-acting tool. Do 4. Separate the baseplate from the barrel. not attempt to operate this or any other tool before obtaining proper training and operator certification.
  • Page 4 IMPORTANT SAFETY INFORMATION SELECTING FASTENERS AND LOADS This manual describes the proper use of the PTP-27 and the safe operating 2. POWER LOAD SELECTION procedures for them; however, THINKING IS YOUR RESPONSIBILITY. You must understand ALL operating principles, safety features and fastening limitations of 1.
  • Page 5 1. FASTENER SELECTION BASE MATERIAL SUITABILITY 1. The PTP-27 is designed to set three types of fasteners, drive pins, Before fastening into any material, give it the center punch test. Using the threaded studs and special assemblies such as drive pins with fastener as a punch, and a hammer, strike a solid blow to the actual material pre-assembled washers, conduit clips and ceiling clips.
  • Page 6 2. Never attempt to alter, modify or manufacture parts for use in your D. DO NOT USE THESE TOOLS FOR FASTENING INTO: Simpson Strong-Tie tool, this can cause malfunctions and result in unsafe 1. Vertical mortar joints. Bricks functioning of the tool.
  • Page 7 Simpson Strong-Tie instructor. Following B. APPLICATIONS FOR THE PTP-27: This tool is capable of making a wide the rules of safe operation given to you here and verbally is range of fastenings;...
  • Page 8 2. Never place your hand over the front (muzzle) end of the tool. Using the PTP-27 tool you have a possibility of stepless power regulation 3. An accidental discharge will seriously injure your hand.
  • Page 9 Simpson Strong-Tie representative for tool repair. RETRACTED INTO THE TOOL). • If at any time during the operation of the tool you feel it is not working properly, STOP using it and call your Simpson Strong-Tie distributor. ¬ Point the tool down and away from yourself, then insert the fastener (head C.
  • Page 10 PARTS LIST OF PTP-27 Handle PTP-611001 12. Piston Stop PTP-514012 23. Mech. Spring PTP-514027 34. Trigger Lever Pin PTP-M85027 Receiver PTP-612002 13. Regulator Bolt PTP-514013 24. Firing Pin spring PTP-514029 35. Ball Bearing, 7mm PTP-M82177 Barrel PTP-613003 14. Regulator Nut PTP-514014 25.