Advertisement

LIMITED WARRANTY (ONE YEAR)
ON SIMPSON STRONG-TIE
Simpson Strong-Tie Company Inc. ("Simpson") provides this limited warranty to
original purchaser. This product, if properly used and maintained in compliance with
all instructions and warnings, will be free from substantial defects in material and
manufacturing for one year from purchase date. Purchaser's sole remedy is replacement
upon return to Simpson within one year of purchase (shipping prepaid).
WHERE LAWFUL, SIMPSON DISCLAIMS ALL OTHER
WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
One Year
A PARTICULAR PURPOSE BEYOND THIS WARRANTY
Limited
PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS
Warranty
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU. WHERE
LAWFUL, UNDER NO CIRCUMSTANCES SHALL SIMPSON
BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES OR DIRECT OR INDIRECT LOSS OF ANY KIND, INCLUDING BUT NOT LIMITED
TO BODILY INJURY, DEATH OR PROPERTY DAMAGE. SIMPSON'S ENTIRE LIABILITY IS
LIMITED TO THE PURCHASE PRICE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. SIMPSON IS IN NO WAY LIABLE FOR
INCIDENTS RESULTING FROM USE WITHOUT PROPER CERTIFICATION OR DISREGARD OF
INSTRUCTIONS AND WARNINGS. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
The PT-27HDA tool complies with OSHA requirements and with ANSI
A10.4 2007 specifications.
Return Tools To:
Northwest U.S.A.
Southwest U.S.A.
Simpson Strong-Tie Co. Inc.
Simpson Strong-Tie Co. Inc.
5151 S. Airport Way
12246 Holly Street
Stockton, CA 95206
Riverside, CA 92509
(209) 234-7775
(800) 999-5099
Southeast U.S.A.
Eastern Canada
Simpson Strong-Tie Co. Inc.
Simpson Strong-Tie Co. Inc.
2221 Country Lane
5 Kenview Boulevard
McKinney, TX 75069
Brampton, ON L6T 5G5
(972) 542-0326
(905) 458-5538
BRAND TOOLS
®
Northeast U.S.A.
Simpson Strong-Tie Co. Inc.
2600 International Street
Columbus, OH 43228
(614) 876-8060
Western Canada
Simpson Strong-Tie Co. Inc.
11476 Kingston Street
Maple Ridge, BC V2X 0Y5
(604) 465-0296
T-A-PT27HDA14 12/14
WARNING
Read This Manual
BEFORE Operating This Tool
OPERATOR'S MANUAL
Model PT-27HDA
5956 W. Las Positas Blvd., Pleasanton, CA 94588 • www.strongtie.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT-27HDA and is the answer not in the manual?

Questions and answers

Summary of Contents for Simpson PT-27HDA

  • Page 1 LIMITED TO THE PURCHASE PRICE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. SIMPSON IS IN NO WAY LIABLE FOR INCIDENTS RESULTING FROM USE WITHOUT PROPER CERTIFICATION OR DISREGARD OF INSTRUCTIONS AND WARNINGS.
  • Page 2: Table Of Contents

    Safety Starts with You ..................1 1. All operators must complete the tool manufacturer’s training before Introduction ....................2 attempting to take an exam or to operate this Simpson Strong-Tie ® General Handling of P.A.T. and Powder Loads ..........3 tool.
  • Page 3: General Handling Of P.a.t. And Powder Loads

    GENERAL HANDLING OF P.A.T. AND POWDER LOADS MAKING SAFE FASTENINGS GENERAL HANDLING OF THE PT-27HDA AND ALL P.A.T. TOOLS BASE MATERIAL SUITABILITY AND THE CENTER PUNCH TEST Before loading the tool or fastening into any material, check the suitability 1. Always point the tool away from yourself and all bystanders.
  • Page 4: The "No's" Of P.a.t. Fastening

    7. Never fasten into material which is too soft, such as wood, plaster, drywall composition board, plywood, etc. This could cause the THE PT-27HDA IS DESIGNED FOR THE FOLLOWING LOADS: fastener to pass through and escape, resulting in serious injury...
  • Page 5: Operating Principles Of P.a.t

    10. Any tool found not to be in proper working condition should be immediately removed from service and tagged “Defective Tool,” CAUTION: The PT-27HDA is capable of fastening into concrete and/or steel. until it has been repaired according to manufacturer’s instructions.
  • Page 6: Schematic And Parts For The Pt-27Hda

    SCHEMATIC AND PARTS FOR THE PT-27HDA TOOL PT-27HDA tool components Part No. Description PTHDA-700801 Stabilizer Plate PTHDA-700820 Spall Shield PTHDA-700330 Guide Assembly (10mm) PTHDA-700340 Guide Assembly (8mm) PTHDA-700303 O-Ring, Guide PTHDA-700302 Buffer PTHDA-700240 Silencer Slide PTHDA-700310 Piston Assembly (10mm) PTHDA-700320...
  • Page 7: Principles And Guidelines For Proper Fastening

    PRINCIPLES AND GUIDELINES FOR PROPER FASTENING PRINCIPLES AND GUIDELINES FOR PROPER FASTENING FASTENING INTO MASONRY MATERIALS: FISH-HOOKING: Masonry materials suitable for fastening into include: “Fish-hooking” is when the fastener curves when driven into concrete. This is caused by the fastener hitting large, hard, or excessive amounts of aggregate, - Poured concrete rebar, or any hard object.
  • Page 8: How To Load And Fire The Pt-27Hda

    HOW TO LOAD AND FIRE THE PT-27HDA TOOL HOW TO LOAD AND FIRE THE PT-27HDA TOOL 4. Depress the tool firmly against the work 5. After making the fastening, lift the tool off 1. Open the tool. Grasp the nosepiece and pull 2.
  • Page 9: Dissassrmbly And Reassembly Of The Pt-27Hda

    DISASSEMBLY AND REASSEMBLY OF THE PT-27HDA DISASSEMBLY AND REASSEMBLY OF THE PT-27HDA DISASSEMBLY DISASSEMBLY (CONT.): Guide Buffer Suppressor 1. Remove the spall suppressor 2. Unscrew the guide using a wrench. 7. Clean the inside of the barrel and piston 6. Pull the piston assembly out of using a wrench.
  • Page 10: Cleaning And Maintenance

    MAINTAINING THE TOOL: PROBLEM POSSIBLE CAUSE REMEDY A clean tool always functions best. The PT-27HDA should be Tool fails to fire Bad power load Change to a new load cleaned each day after normal use or after driving approximately 500...

Table of Contents