Table of Contents
Advertisement
Operation
Tradeworks
Tradeworks
- For portable spray applications of architectural paints and coatings -
(Specifications, page 10.)
IMPORTANT SAFETY INSTRUCTIONS.
Read all warnings and instructions in this
manual and related manuals. Be familiar
with the controls and the proper usage of
the equipment. Save these instructions. See
page 10 for model and series information
including dispense rate, recommended
hose length, guns, and maximum working
pressure.
Tradeworks Project Painter
Model: 826610
™
Project Painter,
™
150 and Tradeworks
™
FIRE AND EXPLOSION HAZARD
•
Use only non-flammable or water-based materi-
als, or non-flammable paint thinners. Do not use
materials having flash points lower than 100°F
(38°C). This includes, but is not limited to, ace-
tone, xylene, toluene, and naphtha. For more
information about your material, request Safety
Data Sheet (SDS) from the supplier.
•
Spraying flammable or combustible materials in
a factory or fixed location must comply with
NFPA 33 and OSHA 1910.94(c) requirements in
the USA and with all similar local regulations in
other countries.
Tradeworks 150
Model: 826620
Visit our website:
http://tradeworkssprayers.com
313381L
170
Tradeworks 170
Model: 826630
ti12937a
EN
Advertisement
Table of Contents
Related Manuals for Graco Tradeworks 170
Summarization of Contents
Operation
Important Safety Instructions
Key safety guidance for operating the equipment.
Fire and Explosion Hazard Warning
Warning about flammability and explosion risks associated with materials.
Warnings
Grounding and Electrical Safety
Guidance on proper grounding and electrical connection requirements.
Fire and Explosion Hazards
Detailed warnings regarding flammable materials and ignition sources.
Specific Hazard Warnings
Covers skin injection, equipment misuse, and material compatibility hazards.
Operational Hazards and PPE
Addresses moving parts, toxic fluids, and necessary protective equipment.
Quick Start-Up Guide
Shutdown and Cleaning - Water-Based Paints
Steps for shutting down and cleaning for water-based paints.
Installation
Grounding and Electric Requirements
Essential grounding and electrical connection guidelines.
Thermal Overload
Information on the motor's thermal overload protection.
Operation
Trigger Lock
How to use the trigger lock for safety.
Pressure Relief Procedure
Steps to safely relieve pressure from the system.
Pressure Control Knob Settings
Explanation of pressure control knob functions.
Setup
Hose and Gun Connection
Steps for connecting the hose and gun.
Setup
Prime and Flush Storage Fluid
Procedure for priming and flushing the sprayer.
Setup
Install Tip and Guard on Gun
Instructions for mounting the spray tip and guard.
Setup
Spraying Techniques
Guidance on achieving proper spray patterns.
Unclogging Spray Tip
Procedure for clearing spray tip clogs.
Setup
Tip Selection
How to choose the correct spray tip size.
Getting Started With Basic Techniques
Aiming Gun
Techniques for proper gun aiming.
Triggering Gun
Correct method for triggering the spray gun.
Shutdown and Cleaning
Pail Flushing
Steps for flushing the sprayer using a pail.
Shutdown and Cleaning
Power Flush
Instructions for a faster flushing method.
Shutdown and Cleaning
Cleaning Gun
Detailed steps for cleaning the spray gun.
Storage
Short Term Storage
Procedures for storing the sprayer for up to two days.
Long Term Storage
Procedures for storing the sprayer for more than two days.
Storage
Stowing Sprayer
Instructions for safely storing the sprayer unit.
Maintenance and Service
Caring for Sprayer
General advice for maintaining the sprayer.
Pump Packings (150/170)
Information on pump packing wear and replacement.
Paint Hoses
Guidance on checking and maintaining paint hoses.
Troubleshooting
Motor Not Running
Solutions for when the motor does not run.
Frozen Pump
How to handle a pump frozen with paint or water.
Troubleshooting
Pump Does Not Prime
Troubleshooting steps when the pump fails to prime.
Pump Cycles but No Pressure
Diagnosing issues when the pump cycles but builds no pressure.
Troubleshooting
Paint Dribbles or Spurts
Addressing issues with paint dribbling or spurting.
Poor Spray Pattern
Solutions for achieving a good spray pattern.
Spray Gun Stopped Spraying
Troubleshooting when the spray gun stops working.
Troubleshooting
Inadequate Coverage
How to fix issues with inadequate paint coverage.
Fan Pattern Variation
Addressing dramatic variations in the spray fan pattern.
Paint Leaks
Identifying and fixing paint leaks from the pump.
Motor Thermal Overload
Troubleshooting intermittent motor operation due to heat.
Need help?
Do you have a question about the Tradeworks 170 and is the answer not in the manual?
Questions and answers