Connecting A Cd Recorder Or Md Recorder; Connecting Equipment With Hdmi Terminals - Denon AVR-987 Operating Instructions Manual

Connecting Other Sources

Connecting a CD recorder or MD recorder

If you wish to perform analog dubbing from a digital source, such as a CD or MD recorder to an
analog recorder such as a cassette deck, you will need to connect the analog inputs and outputs
as shown below, in addition to the digital audio connections.
NOTE:
• Do not connect the output of the component connected to the OPTICAL 4 OUT terminal on
the AVR-987's rear panel to any terminal other than the OPTICAL 4 IN terminal.

Connecting equipment with HDMI terminals

• A simple 1-cable connection (using a commercially available cable) with a device having an HDMI
(High-Definition Multimedia Interface) terminal allows digital transfer of the digital images of DVD-
Video and other sources, and the multi-channel sound of DVD-Audio and DVD-Video.
• To provide audio output from AVR-987's audio output terminal, select "Amp" at the "HDMI In
Assign".
To provide audio output from the TV, select "TV" at the "HDMI In Assign" (
CD recorder /
MD recorder
AUDIO OUT
A
L
L L
R R R
AUDIO IN
A
L
L L
R R
R
D
OPTICAL
OUT
D
OPTICAL
IN
page 49, 50).
Monitor
I
HDMI
IN
DVD player
I
HDMI
OUT
19
Input signals
LINEAR PCM
DVD-Video Dolby Digital
DTS
LINEAR PCM
PACKED PCM
DVD-Audio
(with CPPM /
without CPPM)
CD LINEAR PCM
Multi area
Super Audio
Stereo area
CD
CD area
The AVR-987 is HDMI Ver. 1.1 compatible.
• If your digital monitor or DVD player only supports DVI-D, please obtain and use an HDMI-DVI
conversion cable or adaptor, available from your dealer.
NOTE:
• The audio signals on the multi/stereo area of Super Audio CDs are not output. If the Super
Audio CD is a hybrid CD, only the audio signals in the CD area are output.
• Use a compatible player to play DVD-Audio discs that are copyright protected by CPPM.
• Among the devices that support HDMI, some devices can control other devices via the HDMI
terminal; however, the AVR-987 cannot be controlled by another device via the HDMI
terminal.
• The audio signals from the HDMI terminal (including the sampling frequency and bit length)
may be limited by the equipment that is connected.
• The video signals are not output properly if a device not compatible with HDCP is used.
• When "OFF" is set at "i/p Convert" under "Setting the HDMI Out Setup", use a monitor
compatible with input resolutions of 480i/576i.
• The video signals input from the HDMI input terminals are output to the HDMI monitor with
their original resolution, so the image will not be displayed if the resolutions of the input signal
and the monitor being used are not matched. In this case, change the setting of the resolution
on the source device (player) to one which the monitor can handle.
• For stable signal transfer, we recommend using cables that are a maximum of 5 meters in
length.
2 Connections with an HDMI/DVI-D conversion cable (adapter)
• The HDMI video stream signals (video signals) are theoretically compatible with DVI-D. When
connecting to a monitor, etc., equipped with DVI-D terminals, it is possible to connect using an
HDMI/DVI-D conversion cable, but depending on the combination of devices used the image
might not be output.
• When using an HDMI/DVI-D conversion adapter, the image may not be output properly due to
poor contact with the connected cable, etc..
Connecting Other Sources
2 Copyright Protection System
C C
To play back the digital video and audio of DVD-
Video and DVD-Audio through an HDMI/DVI-D
C C
connection, both the connected player and
C C
monitor are required to support a copyright
protection system called
C C
bandwidth Digital Content Protection System).
HDCP is copy protection technology that
comprises data encryption and authentication
C C
of the partner equipment.
E E
The AVR-987 supports HDCP. Please see the
E E
user's manual of your video display for more
C C
information about this.
HDCP (High-