Advertisement
2. Modifying a Preset
Once you've loaded a pre-
set, turn the
PAGE
knob to
select one of the six parame-
ter pages (Delay, Pitch/EQ,
Reverb, Level, Mod or Alg).
Each page displays a set of
parameters related to the
current setup.
3. Patching
Turn the
PAGE
knob to
select one of the four "Patch"
positions. Select "Src" and
use
ADJUST
to select the
desired controller.
4. Naming your new setup
Turn the
PAGE
knob to
select "Name." The current
setup name will appear in the
upper right of the display
with the first character of the
name underlined.
5. Storing a new sound
Turn the
PAGE
knob to
select "Store."
Note: The LXP-15 II will not perform a store instruction if
"Memory Protect" is enabled. This function is accessed by
turning the
PAGE
knob to "Sys", pressing the button directly
beneath "Mem Prot" and using the
or OFF.
6. Recalling a Register
Turn the
PAGE
knob to
select "Setup."
LXP-15 II Quick Reference Guide
Pressing the button directly
beneath a displayed parame-
ter will select it for adjust-
ment.
Note: The screen will return to its normal 5-parameter display if
you select another parameter, or if 2 seconds pass without
further parameter adjustment. The setup name will be marked
with an asterisk (*) to indicate that the setup has been modified
since it was last stored.
Select "Dest" and use
AD-
JUST
to select the parame-
ter you want to control.
Turning the
ADJUST
knob
will cause the underlined
character to be replaced with
the first letter of the name you
want.
Press the button directly be-
neath "Reg #" on the dis-
play.
ADJUST
knob to select ON
Press the button directly be-
neath "Registr" on the dis-
play.
Note: Pressing the button directly beneath "Reg scan" on the
display allows you to scroll through the registers without loading
them. If you use this method of selection, press the button
directly beneath "Load" on the display to load any displayed
setup.
3 Oak Park, Bedford, MA 01730 USA • Tel: (781) 280-0300 • Fax: (781)280-0490
Turning the
ADJUST
knob
will display the full name of
the selected parameter and
its current value.
Select "Scale" and use
AD-
JUST
to select the control
range for the Destination. As
the Source controller is
moved from min to max, posi-
tive scaling increases (nega-
tive scaliing decreases) Des-
tination values.
The
ADJUST
knob dials
sequentially through a list of
alphanumeric characters in
the following order: (space),
0-9, A-Z, a-z, and an assort-
ment of standard symbols.
Turn the
ADJUST
knob to
select a register number be-
tween 1-128. (Make sure it's
one whose contents you
don't mind overwriting.)
Turn the
ADJUST
knob to
select the register number
you want.
This value will change as you
continue to turn
ADJUST
Pressing
VIEW
will display
the parameters along with
their curent settings.
Select "Thresh n" and use
ADJUST
to set the Source
controller's position relative
to the initial Destination
value. (For most applica-
tions, you can simply leave
Threshold set to 0.)
Pressing the buttons under
"<Char" and "Char>" will step
the underline cursor to the
left and right, allowing you to
choose the characters you
want to change.
When the display shows the
register number you want,
press the button directly be-
neath "Store." The display
will indicate successful stor-
age.
The setup is automatically
recalled.
Copyright © 1994Lexicon Inc. All rights reserved.
.
Advertisement
