Yaesu FT DX 9000 CONTEST - MANUAL 2 Operation Manual page 131

TUNING G
129. MAIN DIAL STEP
Function: Setting of the Main Tuning Knob's tuning
speed on the SSB, CW, and AM modes.
Available Values: 1 or 10 Hz
Default Setting: 10 Hz
130. MAIN DIAL CW FINE
Function: Setting of the Main Tuning Knob's tuning
speed in the CW mode.
Available Values: ENABLE/DISABLE
Default Setting: DISABLE
ENABLE :Tuning in 1 Hz steps on the CW mode.
DISABLE: Tuning according to the steps determined
via menu item 129:
131. 1MHz/100kHz SELECT
Function: Selects the tuning steps for the CLAR/VFO-
B knob when the BAND/MHz button is pressed.
Available Values: 1 MHz/100 kHz
Default Setting: 1 MHz
132. AM CH STEP
Function: Selects the tuning steps for the
microphone's [ UP ] / [ DWN ] keys in the AM mode.
Available Values: 2.5/5/9/10/12.5 kHz
Default Setting: 5 kHz
133. FM CH STEP
Function: Selects the tuning steps for the
microphone's [ UP ] / [ DWN ] keys in the FM mode.
Available Values: 5/6.25/10/12.5/20 kHz
Default Setting: 5 kHz
134. FM DIAL STEP
Function: Setting of the Main Tuning Knob's tuning
speed in the FM mode.
Available Values: 10/100 Hz
Default Setting: 100 Hz
135. MY BAND
Function: Programs a band to be skipped while se-
lecting bands using the CLAR/VFO-B knob.
Available Values: 1.8 ~ 50 (MHz)/GEN/TRV
Default Setting: TRV
To program the band to be skipped, rotate the CLAR/
VFO-B knob to recall the band to be skipped while
selecting bands via the CLAR/VFO-B knob, then press
the [ ENT ] key to change this setting to "ON." Repeat
the same procedures to cancel the setting (skipped
"off"). The skipped band will be high-lighted on the TFT
display.
FT 9000 C
DX ONTEST
ROUP
MAIN DIAL STEP MAIN DIAL STEP .
MAIN DIAL STEP MAIN DIAL STEP MAIN DIAL STEP
O M
PERATION ANUAL
M
TX AUDIO G
136. F-PRMTRC EQ1-FREQ
Function: Selects the center frequency of the lower
range for the front panel's parametric microphone equal-
izer.
Available Values: OFF/100 ~ 700 Hz (100 Hz/step)
Default Setting: OFF
OFF: The equalizer gain and Q-factor are set to
factory defaults (flat).
100 ~ 700: You may adjust the equalizer gain and Q-
factor at this selected audio frequency via
menu items 137:
LEVEL LEVEL LEVEL and 138:
LEVEL LEVEL
BWTH BWTH BWTH .
BWTH BWTH
137. F-PRMTRC EQ1-LEVEL
Function: Adjusts the equalizer gain of the low range
of the front panel's parametric microphone equalizer.
Available Values: –10 ~ +10
Default Setting: +5
138. F-PRMTRC EQ1-BWTH
Function: Adjusts the Q-factor of the low range of the
front panel's parametric microphone equalizer.
Available Values: 1 ~ 10
Default Setting: 10
139. F-PRMTRC EQ2-FREQ
Function: Selects the center frequency of the middle
range for the front panel's parametric microphone equal-
izer.
Available Values: OFF/700 ~ 1500 Hz (100 Hz/step)
Default Setting: OFF
OFF: The equalizer gain and Q-factor are set
to factory defaults (flat).
700 ~ 1500: You may adjust the equalizer gain and
Q-factor at this selected audio frequency
via menu items 140:
LEVEL LEVEL LEVEL LEVEL LEVEL and 141:
BWTH BWTH BWTH .
BWTH BWTH
140. F-PRMTRC EQ2-LEVEL
Function: Adjusts the equalizer gain of the middle
range of the front panel's parametric microphone equal-
izer.
Available Values: –10 ~ +10
Default Setting: +5
141. F-PRMTRC EQ2-BWTH
Function: Adjusts the Q-factor of the middle range of
the front panel's parametric microphone equalizer.
Available Values: 1 ~ 10
Default Setting: 10
M
ENU ODE
ROUP
F-PRMTRC EQ1- F-PRMTRC EQ1- F-PRMTRC EQ1-
F-PRMTRC EQ1- F-PRMTRC EQ1-
F-PRMTRC EQ1- F-PRMTRC EQ1- F-PRMTRC EQ1-
F-PRMTRC EQ1- F-PRMTRC EQ1-
F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2-
F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2-
Page 129